What are the hazards of car-mounted electric kettles to vehicles?

How to Turn Off the Auto Start-Stop Function in Bora Legend?

The auto start-stop button in Bora Legend is located to the right of the gear lever, marked with an 'A'. By default, it is in the 'on' state. To turn it off, simply press the button once. Here is a detailed introduction to the engine auto start-stop system: 1. The engine auto start-stop system automatically shuts off the engine when the vehicle comes to a temporary stop (e.g., at a red light) and restarts it when it's time to move again. This system is achieved by equipping the traditional engine with an enhanced motor that has idle start-stop functionality, allowing the engine to completely shut off when idle stop conditions are met. When the vehicle needs to move again, the idle start-stop motor system quickly responds to the driver's start command, rapidly restarting the engine for seamless transition, significantly reducing fuel consumption and exhaust emissions. 2. The working principle is that when the vehicle stops due to traffic congestion or at an intersection, the driver presses the brake pedal and shifts to neutral. At this point, the Start/Stop system automatically checks: the engine is idling and not in gear; the wheel speed sensors of the anti-lock system show zero; the electronic battery sensor indicates sufficient energy for the next start. 3. Once these three conditions are met, the engine automatically stops. When the traffic light turns green, the driver presses the clutch (in manual transmission models), and the 'start-stop' function can be activated immediately, quickly restarting the engine. In automatic transmission models, simply releasing the brake or turning the steering wheel will automatically restart the engine, allowing the driver to accelerate immediately, all while remaining in D (Drive) mode.

13

5

Share

What Causes the Steering Misalignment in Geely Emgrand GL?

There are many reasons for steering misalignment, usually due to steering gear failure, inconsistent tire pressure, or uneven tire wear. If the Geely Emgrand GL experiences severe deviation, it is recommended to promptly visit a repair shop for inspection to ensure driving safety. Below are solutions for steering misalignment in the Geely Emgrand GL: 1. Check and adjust tire pressure: Significant differences in tire pressure can cause the steering wheel to pull to the left or right. Generally, if such a situation is noticed, tire pressure should be checked first. 2. Perform a four-wheel alignment: Over time, wear and tear on chassis components can alter alignment angles, leading to deviation while driving or steering misalignment. 3. Perform wheel balancing: A car's wheel is an assembly of the tire and rim, but manufacturing imperfections can cause uneven mass distribution. At high speeds, this imbalance can cause wheel wobble or steering wheel vibration. To prevent or correct this, weights are added to balance the wheel's edges—a process known as dynamic balancing. 4. Adjust the steering tie rod: If tire inspection and four-wheel alignment do not resolve the steering misalignment, adjusting the steering tie rod may help. First, restore the steering wheel's center position by adjusting the tie rod length, typically by adjusting both sides—shortening one side while lengthening the other—ensuring equal travel to maintain proper toe alignment.

14

4

Share

Which engine is used in the Jiangling Ford Lingyu?

ECOBOOST4G20D6L is the engine model used in the Jiangling Ford Lingyu, with a maximum horsepower of 224 hp, a maximum power of 165 KW, a maximum power speed of 5500 rpm, and a peak torque of 360 N.m. The Ford Lingyu engine is independently developed and manufactured by Jiangling Motors. For the daily maintenance of the Jiangling Ford Lingyu engine, the following methods can be used: Use lubricating oil of the appropriate quality grade. For gasoline engines, SD--SF grade gasoline engine oil should be selected based on the additional devices of the intake and exhaust systems and usage conditions; for diesel engines, CB--CD grade diesel engine oil should be selected based on mechanical load, with the selection standard not lower than the requirements specified by the manufacturer. Regularly change the oil and filter. The quality of any grade of lubricating oil will change during use. After a certain mileage, the performance deteriorates, which can cause various problems for the engine. To avoid faults, the oil should be changed regularly based on usage conditions, and the oil level should be kept moderate. When the oil passes through the fine holes of the filter, solid particles and viscous substances in the oil accumulate in the filter. If the filter is blocked and the oil cannot pass through the filter element, the filter element may burst or the safety valve may open, allowing the oil to pass through the bypass valve and bring dirt back to the lubrication parts, accelerating engine wear and internal contamination. Regularly clean the crankcase. During engine operation, high-pressure unburned gas, acid, moisture, sulfur, and nitrogen oxides from the combustion chamber enter the crankcase through the gap between the piston rings and cylinder walls, mixing with metal powder generated by part wear to form sludge. A small amount of sludge remains suspended in the oil, while a large amount precipitates out, blocking the filter and oil holes, making engine lubrication difficult and causing wear. Regularly use a radiator cleaner to clean the radiator. Removing rust and scale not only ensures the normal operation of the engine but also extends the overall lifespan of the radiator and engine.

12

4

Share

Where is the Daytime Running Light Switch on the Leiling?

The location of the Leiling daytime running light switch: The Leiling daytime running lights generally do not have a switch and will automatically illuminate after the vehicle is started. Below is relevant information about daytime running lights: 1. Daytime running lights, as the name suggests, are lights that are turned on when the vehicle is driven during the day. This concept was proposed by EU countries. Because EU countries often have snow and fog, resulting in very low visibility, some countries have issued regulations: lights must be turned on during daytime driving. Its function is not to allow the driver to see the road clearly, but to let others know that a car is approaching. 2. Manual operation method to turn off daytime running lights: Insert the ignition key, with the ignition switch in the off position, move the turn signal switch to the left turn position, pull up the high beam and hold it, then turn on the ignition switch. Hold for about 5 seconds, and after hearing a prompt sound, release the ignition switch and return it to the original position. The daytime running lights will be turned off. Conversely, to turn on the daytime running lights, the operation is basically the same as turning them off, just change the left turn to the right turn.

1

Share

Where is the gasoline filter located on the Jianghuai Tongyue?

Jianghuai Tongyue gasoline filter location: The built-in gasoline filter of the Jianghuai Tongyue is located inside the fuel tank. Open the fuel tank cap to see the fuel pump assembly, and then disassemble the fuel pump to access the fuel filter. Remember to replace the gasoline filter regularly. If not replaced, the gasoline filter may become clogged. Here are some issues related to a clogged gasoline filter: 1. Difficulty starting the engine, insufficient power, and slow acceleration; 2. Incomplete filtration of gasoline, leading to excessive carbon deposits during engine operation and possible knocking; 3. Sudden engine stalling during normal driving, posing safety risks.

10

5

Share

How to Disassemble a Dash Cam?

First, use a blade or card-like object to pry open the front panel to reveal the screw holes inside the dash cam. Use a screwdriver to remove the screws, then the display panel can be detached. There are clips around it; gently pry them with a screwdriver to remove the panel. After removing the panel, the circuit board will be visible. There are four screws located in relatively hidden positions around the circuit board display. Once these are removed, the back cover can be taken off.

3

Share

What are the hazards of car-mounted electric kettles to vehicles?

How to Turn Off the Auto Start-Stop Function in Bora Legend?

What Causes the Steering Misalignment in Geely Emgrand GL?

Which engine is used in the Jiangling Ford Lingyu?

Where is the Daytime Running Light Switch on the Leiling?

Where is the gasoline filter located on the Jianghuai Tongyue?

How to Disassemble a Dash Cam?

How to Activate the Bora Locking Beep Sound?

How to Replace the Battery in a Lincoln Car Key

Where is the cabin air filter of Changan V7 located?

Does the Mercedes-Benz C180L have ambient lighting?