What are the hazards of a CNG ignition advance device?

1 Answers
MacJosephine
07/29/25 8:27pm
The hazards of a CNG ignition advance device include: 1. It may lead to a shortened engine service life; 2. It can make the car slower to start and more prone to stalling. Precautions when installing a CNG ignition advance device include: 1. Before installation, ensure that the wiring harness setup of the ignition advance device matches the vehicle model to be modified; 2. During installation, keep it away from areas exposed to rain, moisture, and high temperatures; 3. Keep it away from high-voltage ignition wires and maintain good insulation. The ignition advance device can automatically adjust the ignition timing angle, ensuring the engine operates at the ideal ignition timing angle under different speeds. It can accommodate both fuel and gas conditions without altering the original engine compression ratio or combustion structure. Based on the position of the conversion switch, it enables precise control of different ignition timing angles for dual-fuel vehicles through microcontroller control.
Was this review help?
2
0
Share
More Forum Discussions

How to Deal with a Fallen Canopy Cover?

When encountering a situation where the canopy cover has fallen, the following methods should be used to handle it: 1. Partial detachment near the edge: In this case, simply peel open the edge, spray adhesive, let it dry for 3-5 minutes, and then reattach. 2. Large-scale detachment of the canopy: At this point, the entire canopy needs to be removed, the old canopy fabric taken off, the surface of the aged sponge cleaned, and a new piece of canopy fabric prepared along with specialized canopy adhesive. Apply adhesive to both sides, let it dry for 3-5 minutes (until it's no longer sticky to the touch), then reattach, and finally reinstall the canopy. 3. Precautions: If you are unable to repair it yourself, seek assistance from a professional auto repair shop.
14
2
Share

The Advantages and Disadvantages of Private Cars

Below is a detailed introduction to the advantages and disadvantages of private cars: 1. Advantages: Cars allow people to reach their destinations directly, with relatively fast speed and comfort. In today's era where efficiency and time are money, the convenience of transportation brings enormous benefits to humanity. Travel has become unrestricted, and people's lifestyles, concepts, and quality of life have changed due to cars. 2. Disadvantages: The increase in private cars has led to a situation where oil supply is less than demand, keeping oil prices high. Industries such as agriculture, manufacturing, and light industry all rely on oil for production, increasing production costs and keeping product prices elevated.
9
5
Share

What does km/h mean on a car?

km/h stands for kilometers per hour, indicating the current speed of the vehicle. Below is a related introduction: 1. Definition: km/h is the abbreviation for 'kilometers per hour' in English, specifically displayed on the car's speedometer to show your current driving speed. 'km' stands for kilometers, representing the distance traveled by the vehicle. 2. Speed conversion: 1 meter per second (m/s) = 3.6 kilometers per hour (km/h). 'km' refers to kilometers, where 1 kilometer = 1000 meters = 1 kilometer. The conversion method is to divide km/h by 3.6 to get m/s, or multiply m/s by 3.6 to get km/h. The conversion process is as follows: 1 km/h = 1000 m / 3600 s = (1/3.6) m/s, so 1 m/s = 3.6 km/h.
15
0
Share

What is the difference between symmetric and asymmetric tire tread patterns?

About the difference between symmetric and asymmetric tire tread patterns, the relevant introduction is as follows: 1. Different patterns: Asymmetric tread patterns refer to tire patterns where the left and right sides are inconsistent with the center groove of the tread as the reference; Symmetric tread patterns refer to tire patterns where the left and right sides are the same or similar with the center groove of the tread as the reference, or the pattern can completely overlap after rotating the other side by 180 degrees. 2. Different performance: The tread blocks of asymmetric patterns are larger than those of symmetric patterns, the contact area between the tread and the ground is larger, and the grip is also greater. Tires with asymmetric patterns have more prominent sports performance; Symmetric patterns have good quietness and comfort, and the rolling resistance of the tire is small. 3. Different uses: Asymmetric patterns are mainly used for sports performance cars and sports SUVs; Symmetric patterns are mainly used for general economical family cars, urban SUVs and off-road SUVs.
13
0
Share

Should I Apply the Car Film Provided by the 4S Store?

Most of the car films provided by 4S stores are low-cost, inferior quality films. If you are not too particular, you can accept the film offered by the 4S store. If you have some standards, you might consider paying extra to upgrade to a better film. Some so-called "original factory films" from 4S stores are essentially just plastic sheets with no heat insulation effect, strong odors, and excessive formaldehyde levels. They may bubble up within a few months, and removing them can leave behind a lot of difficult-to-remove adhesive. Below are some precautions to take after applying the film: 1. Do not roll down the windows: After applying the car film, avoid rolling down the windows for a week. In most cases, the car film takes 5-7 days to fully adhere to the window. During this period, try not to roll down the windows to prevent the film from shifting before it is completely bonded. 2. Do not wipe: Avoid wiping the film for a week after application. Newly applied films may develop fogging, which is a normal part of the drying process. This condition usually lasts for about a week to half a month. Simply wait for the fogging to disappear naturally and avoid wiping it. 3. Avoid using sharp or hard tools to scrape: After applying the car film, never use sharp or hard tools to scrape it. If you accidentally do so, the transparency of the film will be significantly compromised.
9
3
Share

Where are the drain holes located on car doors?

The drain holes on car doors are located along the lower edge of the door. The function of door drain holes is to allow water that enters the door to drain out during rain. All car doors have these drain holes, as some water inevitably enters the door through the gap between the weatherstripping and window glass during rain or car washing. Car drain holes serve to reduce vibration and noise while extending the lifespan of the exhaust muffler system. Primarily used in light vehicles, compact cars, and buses, their structure consists of a double-layer corrugated pipe covered with a steel wire mesh sleeve, with clamping rings at both straight ends. For better noise reduction, the corrugated pipe may contain expansion joints or mesh sleeves internally. Drain holes are critically important for car doors. If they become clogged, rainwater will accumulate inside the door, leading to rust formation and potentially causing malfunctions in door locks and window regulators. When clogged, the door panel must be removed to clear the obstruction to prevent door damage. Other drain holes in cars include: Sunroof drain holes: Sunroofs typically have four hidden drain holes that can become clogged if neglected. Each connects to a hose leading to the front or rear of the vehicle. Engine compartment drain hole: Located at the rear of the engine compartment, below the windshield edge near the air intake, housing the wiper motor and mechanism. AC drain hole: Usually positioned below or in front of the passenger seat, under the evaporator unit, connected to the chassis via a hose. Fuel filler cap drain hole: Situated below the fuel filler cap, crucial for preventing moisture damage to metal components like the fuel cap and door panels.
13
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.