What are the functions of the Honda Vezel car key?

1 Answers
MarleyFitz
07/25/25 3:21am
The Honda Vezel car key has three main functions: remote unlocking and locking of the car, and mechanical starting of the car. Remote unlocking and locking allow you to lock and unlock the doors from a distance without inserting the key into the keyhole, making it convenient to operate without locating the keyhole. Mechanical starting requires inserting the key to start the car. The Honda Vezel key mainly consists of a transmitter and a receiver. The transmitter is used to send radio signals, with each press sending a signal. The receiver can capture the identification code transmitted by the transmitter via shortwave modulation through the car's shortwave antenna, which is then processed by the distributor into the receiver's electronic control unit for shortwave high-frequency amplification and demodulation. The demodulated identification code is compared; if the code is correct, it is input into the control circuit to activate the actuator. The ignition key with a remote transmitter (available on certain models only) includes unlock and lock buttons. Reasons and solutions for remote battery failure: If the battery is dead or has poor contact, replace the battery promptly; if the time control module in the remote key fails, visit a professional repair shop to replace the control module; if the car's remote transmitter antenna is aging, go to a service station for inspection and repair.
Was this review help?
8
2
Share
More Forum Discussions

What is the reason for the Volkswagen flip camera flipping but no image?

The reason for the Volkswagen flip camera flipping but no image may be due to a camera malfunction or a loose or broken power cable. If it's a camera malfunction, you need to purchase and install a new one. If the power cable is loose, causing the camera to lose power, simply plug the power cable back in tightly. Definition of reversing camera: The reversing camera, also known as a parking assist system, or vehicle backup camera system, or onboard monitoring system, etc. English name: vehicle-backup-camera. This system is widely used in various large, medium, and small vehicles for reversing or driving safety assistance. Precautions for reversing camera: Reversing camera display issues mostly occur in vehicles where the camera was installed aftermarket. The main problems lie with the product quality and installation work. To avoid future issues, car owners who want to install a reversing camera must purchase a good product and have it installed by a professional repair shop. Otherwise, if there are problems with the wiring, troubleshooting can be very troublesome.
19
2
Share

What is the height of the Audi R8 body?

The latest Audi R8 V10 Coupe has a body height of 1236 mm, while the latest V10 Spyder model stands at 1255 mm. The vehicle features a wheelbase of 2650 mm, is configured as a two-door, two-seater sports car, and has a fuel tank capacity of 83 liters. Here is some relevant information about the Audi R8: 1. The R8's body sits close to the road, with a muscular rear end. The transition between the doors and the side air vents is harmoniously designed. Between the wheel arches and the roof behind the doors, there are wide air intakes that provide sufficient airflow for the V8 engine's intake and cooling. 2. The Audi R8's front grille design replaces the original silver chrome trim with black plastic strips. The headlights have been redesigned, with horizontal L-shaped daytime running lights that are sharper than the current model. The turn signals, composed of six recessed light sources, have been redesigned and positioned above the headlights. 3. At the rear, the taillights have been redesigned with a flat figure-eight shape that appears more aggressive than the previous square design. The current oval exhaust pipes have been replaced by round ones.
6
5
Share

What is the purpose of using a tension pulley in belt drive?

The purpose of using a tension pulley in belt drive is to adjust the initial tension of the belt. Here are some relevant details: 1. A tension pulley is a follower wheel that presses against the belt to control its tension. It serves as a tensioning device in belt drives. When the center distance of the pulleys cannot be adjusted, a tension pulley can be used to tighten the belt. Belt pulleys rely on friction for transmission, so the belt must be tensioned during installation. However, after some time in operation, the belt may stretch and become loose, leading to slippage, and must be re-tensioned. 2. When the center distance between two drive pulleys cannot be adjusted, a tension pulley must be used to ensure normal transmission and prevent slippage. The tension pulley uses mechanisms such as springs or hydraulic pressure to generate a force that tightens the belt, ensuring it applies appropriate pressure on the working pulley. The tension pulley presses against the outer side of the slack side. The latter causes the belt to undergo reverse bending, which may reduce its lifespan. This type of device is commonly used in drives where an increased wrap angle is needed or where space is limited.
9
5
Share

What Are the Techniques for Driving a Manual Transmission Car on Highways?

Manual transmission high-speed driving techniques are as follows: Gear shifting techniques: Do not wait until the RPM is too low and the vehicle has almost no power before downshifting, as this will increase the engine load. It is necessary to maintain a certain driving force and speed for the vehicle to reduce the engine load, and early downshifting is essential, especially when going uphill, driving at low speeds, or carrying heavy loads. Throttle control: This is essentially a practice of foot sensitivity. When parked in neutral, press the throttle and see if you can keep the RPM fixed at a certain level. Once mastered, you can practice this step while driving, as the first gear has a large speed ratio (similar to a long lever arm), making throttle sensitivity the highest and control the most challenging. Gear shifting timing: Gear shifting is a manual action to change the gear ratio of the transmission to adapt to different road conditions and driving performance. Downshifting is suitable for overtaking and downhill driving (engine braking); upshifting is suitable for high-speed driving, reducing RPM, and lessening the engine load.
1
3
Share

What Causes the Car to Roll Even When the Handbrake is Engaged?

If the car rolls even when the handbrake is engaged, the reason may be that there is slack in the handbrake. You can try tightening the handbrake cable. Here are solutions for automatic and manual transmission cars when the handbrake is engaged but the car still rolls: Manual Transmission: Press the clutch with your left foot and the brake with your right foot, engage any forward gear, pull the handbrake, then turn off the engine. Use the traction of the gear to prevent the car from rolling. Automatic Transmission: Press the brake, shift into P (Park), engage the handbrake, and finally turn off the engine. Utilize the locking mechanism of the automatic transmission's P gear to prevent further rolling. Additional Information: If you notice the car rolling, immediately stop it using the handbrake or foot brake. After stopping, place triangular blocks, stones, etc., under the rear wheels before starting again. If the car's brakes fail to stop it, control the direction to avoid pedestrians or hazardous objects on the road, then steer the rear of the car toward natural obstacles on the roadside to halt the vehicle's movement.
3
3
Share

How long does it take for a canceled license plate to be released?

The license plate is retained for six months after cancellation. When a vehicle is scrapped, the owner can apply to the vehicle management office to retain the license plate number within six months after completing the transfer or cancellation registration. Here is the relevant information: Replacing a vehicle license plate: Bring your vehicle license and original ID card, along with a copy, to the vehicle management office. Fill out the application form for license plate replacement, submit your original license plate, and pay a processing fee of 100 yuan. According to regulations, this replacement procedure is usually completed within one working day. Canceling a vehicle license plate: A vehicle license plate can be canceled, but the vehicle must have been registered under the owner's name for at least three years. Bring the vehicle license to the traffic police department to apply. There are only two scenarios where a license plate may be canceled: vehicle scrapping or vehicle transfer. The inspection department will issue a written notice to the vehicle owner two months (60 days) in advance if the vehicle is nearing the end of its service life, requiring them to complete the relevant procedures (applying for an extension or cancellation due to scrapping) at the vehicle management office. If the owner fails to complete the procedures after receiving the notice, the cancellation will be processed in accordance with Article 61 of the Ministry of Public Security's 'Registration Specifications.'
9
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.