···
Log in / Register

What are the full score requirements for reverse parking?

5 Answers
Eli
08/28/25 3:21am
The full score requirements for reverse parking are as follows: Requirement 1: During the test, the vehicle must not stop while moving forward or backward. Start by reversing into the garage from the control line at one end of the road (the vehicle body must cross the control line), then move forward out of the garage and pass the control line at the other end before reversing into the garage again to park. Finally, move forward out of the garage. Requirement 2: Drive according to the specified route and sequence. Requirement 3: The vehicle body must not cross the line. Requirement 4: There is a time limit for reverse parking; both left and right reverse parking must be completed within 210 seconds. Exceeding this time will result in an immediate deduction of 100 points. Requirement 5: The vehicle must not stop during the test, which places higher demands on the use of the clutch. During practice, it is essential to use the clutch frequently and learn to control the vehicle speed flexibly by using the clutch. The goal is to move slowly without stopping, maintaining a speed of around 5 km/h to complete the entire reverse parking maneuver smoothly.
Was this review help?
15
0
Share
MacFelix
09/09/25 8:42am
The full-score requirements for reverse parking are quite demanding. I practiced this every day when getting my driver's license. The car body must not touch any solid or dashed lines, and even brushing against the corner lines of the parking space will result in point deductions. The distance to the parking space corner seen in the rearview mirror should be controlled at around 30 cm, and the timing of steering wheel operation is particularly crucial. When reversing in, both the front and rear bumpers must be completely inside the parking space, and the car body must be parallel to the side lines of the parking space as seen in the left and right rearview mirrors. Stopping midway during the entire test is not allowed, and the clutch must be controlled steadily. Before starting, the turn signal must be activated, and turning it off too early or forgetting to turn it on will result in point deductions. I remember being most afraid of the car body being crooked during the test, so I always counted the turns when straightening the steering wheel. Practicing with multiple reference points helps develop a feel for it, and adjusting the rearview mirrors accurately increases the success rate.
Was this review help?
14
3
Share
Expand All
Nelson
10/24/25 2:46am
As someone who frequently accompanies practice sessions, I understand that a perfect parallel parking requires precise positioning. None of the four wheels can cross the line, and both the front and rear of the car must be completely within the frame when parking. Observing through the rearview mirrors is particularly crucial—you need to turn the steering wheel when the left corner of the parking space appears at the bottom edge of the mirror. Maintain a steady speed while reversing; stopping for more than two seconds will result in point deductions. The distance between the car body and the parking lines must be even—too much discrepancy on either side leads to immediate failure. Steering wheel movements should be decisive; a half-second delay in straightening will cause misalignment. I recommend using the raised part of the windshield wiper or the rearview mirror housing as reference points during practice. The directional sense honed during parallel parking proves especially useful here.
Was this review help?
2
4
Share
Expand All
JeremiahLynn
10/24/25 2:48am
The most challenging part of scoring full marks in reverse parking is accurately positioning the car. The vehicle must not touch the lines around the parking space, and running over the lines with the wheels will result in an immediate failure. When you see the corner of the parking space appear in the rearview mirror, turn the steering wheel fully. Once the car body aligns parallel with the parking lines, immediately straighten the wheel. After entering, ensure the entire car is within the space, with neither the front nor the rear extending beyond the white lines. Do not stop during the reversing process, and press the clutch pedal as gently as stepping on an egg. During my driving test, I was most worried about parking crookedly, so I always stretched my neck to check the rearview mirror after each reverse. Remember to turn on the left turn signal before starting; this small detail is often overlooked by many.
Was this review help?
18
0
Share
Expand All
VanRafael
12/07/25 3:09am
To score full points in reverse parking, pay special attention to three aspects: position, distance, and timing. No part of the vehicle should cross the parking space lines, and all four wheels must be within the lines to be considered properly parked. When reversing, carefully observe the side mirrors and maintain a distance about the width of a water bottle between the vehicle body and the corner of the parking space. The vehicle must not stop during the entire process; pausing the wheels for more than two seconds will result in point deductions. After parking, the vehicle must be straight, with the difference in width on both sides not exceeding the width of three fingers. Steering wheel operation should be quick, precise, and steady—turning too early or too late will cause misalignment. During practice, it's recommended to place a small sticker on the window as a reference point. Before starting the test, always remember to activate the turn signal in advance; forgetting to do so will result in an immediate 10-point deduction.
Was this review help?
9
4
Share
Expand All
More Forum Discussions

How many liters of oil should be added to a BMW X1?

The oil filling capacity for a BMW X1 is generally 4.5L, but it may vary depending on different vehicle configurations. Therefore, car owners need to add oil based on the actual condition of their vehicles. The amount of oil added can affect the operation of the engine, thereby influencing the normal functioning of the car. Below is some relevant information about engine oil: 1. Engine oil, as a lubricant for the engine, is equivalent to the 'blood' of a car and plays a very important role. It is also crucial for maintaining the lifespan of the engine. Of course, its functions are diverse, mainly including lubrication and wear reduction, auxiliary cooling, sealing and leak prevention, rust and corrosion prevention, and shock absorption. 2. The choice of lubricant is very important for the engine. Only by selecting the appropriate lubricant can the wear of engine parts be reduced, thereby extending the engine's lifespan. However, the most expensive lubricant is not necessarily the best; only the lubricant that matches the engine is the best and most suitable. Therefore, choosing the right lubricant is very important for the engine.
8
1
Share

Does BMW have a spare tire?

BMW older 5 Series models have a spare tire, located under the floor in the trunk. New models do not have one. The reason why the new BMW models do not come with a spare tire is because they use run-flat tires. The advantage of run-flat tires is that they enhance driving feel and handling. The classifications of spare tires are as follows: 1. Full-size spare tire: A full-size spare tire has the exact same specifications as the other four tires on the vehicle and can replace any temporarily or permanently unusable tire. 2. Compact spare tire: This type of spare tire has a slightly smaller diameter and width compared to the other four tires, so it can only be used as a temporary replacement and should only be used on non-driving wheels. Additionally, the maximum speed should not exceed 80 km/h. 3. Run-flat tire: Also known as a safety tire (run-flat tire), commonly referred to as a "run-flat tire," the industry directly translates it as "tire that can run when flat." Compared to regular tires, run-flat tires do not lose air or lose air very slowly when punctured, maintaining the driving profile, and the tire bead remains fixed on the rim, ensuring the car can drive for a long time or temporarily to a service station.
8
1
Share

How many liters of transmission oil does the Elantra require?

Elantra requires 4 liters of transmission oil. Introduction to Elantra: 1. Elantra is a typical model under Beijing Hyundai. The car's intake grille features a full chrome-plated design, exuding a sense of high-end fashion. The design includes a relatively short rear end, which enhances the sporty feel. 2. Elantra is a global model that Hyundai first launched overseas. The car has a body length of 4570mm, width of 1775mm, and height of 1445mm. It is equipped with a multifunctional steering wheel that includes buttons for audio, cruise control, Bluetooth calling, and more. The buttons are specifically designed in an arc shape for greater convenience. Additionally, it features dual-zone automatic air conditioning, with a very clear and rational layout in the most compact spaces.
10
1
Share

What is the ground clearance of the BJ80?

The minimum ground clearance of the BJ80 is approximately 250 millimeters, a height that allows this vehicle to handle most complex road conditions. The BJ80 is a rugged off-road vehicle, equipped with a 2.3-liter turbocharged engine across all models. This engine delivers a maximum power of 170 kilowatts and a peak torque of 345 Newton-meters, paired with a 6-speed automatic transmission. The BJ80 features a part-time four-wheel-drive system, which enhances its off-road capabilities. This four-wheel-drive system offers three modes: high-speed four-wheel-drive mode, low-speed four-wheel-drive mode, and high-speed two-wheel-drive mode. The dimensions of the BJ80 are 4765 millimeters in length, 1955 millimeters in width, and 2005 millimeters in height, with a wheelbase of 2800 millimeters.
18
1
Share

Can 92 and 95 gasoline be mixed?

92 gasoline and 95 gasoline cannot be mixed because their isooctane content is different. 92 gasoline is suitable for engines with low compression ratios, while 95 gasoline is suitable for engines with high compression ratios. If 92 gasoline is added to a car that should use 95 gasoline, abnormal combustion may occur, leading to knocking. Knocking not only damages the combustion chamber but also directly affects the normal operation of the engine, and in severe cases, may cause engine damage. If 95 gasoline is added to a car that should use 92 gasoline, although it will not damage the engine, 95 gasoline is more expensive than 92 gasoline, resulting in waste. The difference between 92, 95, and 98 gasoline: Standard gasoline is composed of isooctane and n-heptane. Isooctane has good anti-knock properties, and its octane number is defined as 100; n-heptane has poor anti-knock properties and is prone to knocking in gasoline engines, so its octane number is defined as 0. If the gasoline is labeled as 92, it means that this gasoline has the same anti-knock properties as standard gasoline containing 92% isooctane and 8% n-heptane. The same principle applies to 95 and 98 gasoline. What to do if the wrong gasoline is added: If gasoline with a higher octane number than specified is added, for example, adding 95 gasoline when 92 is specified, simply switch back to 92 gasoline after the current fuel is consumed. If gasoline with a lower octane number than specified is added, for example, adding 92 gasoline when 95 is specified, you can add a high anti-knock fuel additive. Of course, you can also directly drain the fuel and refill with 95 gasoline. To find out which gasoline your car requires, you can check the car's user manual or the fuel label on the fuel tank cap.
15
2
Share

What transmission is used in the BJ80?

All models of the BJ80 use a 6AT transmission, which offers good reliability and durability. AT transmissions can also withstand high torque. The AT transmission is also known as a torque converter transmission, and it is connected to the engine via a torque converter. There are three common types of automatic transmissions: dual-clutch transmission (DCT), AT transmission, and CVT transmission. The CVT transmission has good reliability and durability, but it cannot withstand high torque. The dimensions of the BJ80 are 4765 mm in length, 1955 mm in width, and 2005 mm in height, with a wheelbase of 2800 mm.
19
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.