···
Log in / Register

What are the foot movements when turning in Subject 3?

3 Answers
SanEvangeline
09/04/25 8:05am
Before making a turn, step on the brake to slow down and shift to second gear, then accelerate after completing the turn. Below is a related introduction to Subject 3: Introduction: Subject 3, including the road driving skills test and the safety and civilized driving knowledge test, is part of the motor vehicle driver's license assessment. It is the abbreviation for the road driving skills and safety and civilized driving knowledge test subjects in the motor vehicle driver's examination. Test content: preparation for getting on the car, simulated lighting test, starting, driving in a straight line, shifting gears, changing lanes, parking by the roadside, going straight through intersections, turning left at intersections, turning right at intersections, passing through pedestrian crossings, passing through school zones, passing through bus stops, meeting vehicles, overtaking, making U-turns, and driving at night.
Was this review help?
15
5
Share
LouisAnn
09/17/25 2:08am
As a driving instructor, I must emphasize the importance of coordinating the clutch and accelerator during turns in Subject 3. When you see the curve deceleration sign, first gently press the brake with your right foot to reduce the speed below 30 km/h, while simultaneously pressing the clutch pedal all the way down with your left foot. As the car enters the curve, slowly release the clutch to the half-engagement point with your left foot. Once the steering is properly aligned, quickly apply some throttle with your right foot to prevent stalling. The biggest mistake during a turn is coasting with the clutch pressed—this will result in an immediate failure during the test. After exiting the curve, when you feel the car is straight, fully release the clutch. The entire process should be executed smoothly, just like an experienced driver.
Was this review help?
16
3
Share
Expand All
StKing
10/31/25 2:37am
Driving an automatic transmission car around turns is much simpler! Gently apply the brake with your right foot in advance to slow down to 20-30 km/h, maintaining this speed as you enter the turn. When steering, move your foot from the brake to the accelerator and let the car coast at idle speed for the safest approach. Never turn while braking, as it increases the risk of being rear-ended. Remember to glance at the rearview mirror before turning—if a car is too close, wait a moment. When gently accelerating out of the turn, ensure the steering wheel straightens in sync with the increasing speed to avoid wobbling.
Was this review help?
4
3
Share
Expand All
More Forum Discussions

How to Modify the Toyota Yaris Key?

Toyota Yaris key modification requires professional operation by technicians at a 4S dealership. Taking the 2021 Toyota Yaris Leading Edition as an example, it is classified as a compact car with body dimensions of 4160mm in length, 1700mm in width, 1495mm in height, and a wheelbase of 2550mm. The body structure is a 5-door, 5-seat hatchback with a fuel tank capacity of 42 liters. The 2021 Toyota Yaris Leading Edition is equipped with a 1.5L naturally aspirated engine, delivering a maximum horsepower of 112PS, with peak power achieved at 6000 rpm and maximum torque at 4200 rpm. It is paired with an 8-speed continuously variable transmission (CVT).
10
1
Share

Where is the start-stop switch located on the Fengshen AX7?

The start-stop switch on the Fengshen AX7 is located below the left side of the steering wheel, featuring a button with the letter 'A' inside a circle. Taking the 2021 Fengshen AX7 Manual Zhixiang Edition as an example, it belongs to the compact SUV category, with body dimensions of 4645mm in length, 1880mm in width, and 1670mm in height, a wheelbase of 2715mm, and a fuel tank capacity of 61 liters. The 2021 Fengshen AX7 Manual Zhixiang Edition is equipped with a 1.5L turbocharged engine, delivering a maximum horsepower of 150PS, with the maximum power achieved at 5500rpm and the maximum torque available between 1800 to 4000rpm.
4
1
Share

What are the reasons for the alarm sounding on the JAC Refine S3?

There may be several reasons for the alarm sounding: 1. The sensitivity of the trigger is too high: The alarm may activate in response to minor vibrations or small noises. Sometimes, excessive vibration can also trigger the car alarm. If the alarm is too sensitive, you can fine-tune it using the sensitivity adjustment knob on the anti-theft vibration sensor. 2. Doors not properly closed: This includes not only the car doors but also the engine hood or the trunk. If any of these components are not securely closed, the car alarm will activate. If not addressed, the alarm will continue to sound until the car battery is drained or the door is properly closed. 3. Controller malfunction: The alarm may sound due to a faulty, short-circuited, or failed controller in the alarm system. During daily driving, if the car alarm sounds, it is important to promptly check if someone is tampering with the vehicle. If the alarm activation is not caused by human interference, a thorough inspection is necessary.
20
1
Share

Which has higher fuel consumption between JAC Refine 2.0 and 2.4?

The fuel consumption of Refine's 2.0 and 2.4 models is basically similar. In urban driving, the 2.4 model consumes about 1 liter more, but on highways, the 2.4 model is more fuel-efficient than the 2.0. Below is relevant information: 1. Fuel consumption: Fuel consumption generally refers to constant-speed fuel consumption. Constant-speed fuel consumption is the vehicle's fuel consumption per 100 kilometers obtained in constant-speed driving fuel consumption tests specified by national standards for certain types of vehicles. 2. JAC Group: JAC Group has a high-level R&D team of nearly 5,000 people, adhering to the key technology R&D route of "energy saving, environmental protection, safety, intelligence, connectivity, and comfort." It has formed a complete forward R&D system including the R&D of complete vehicles, core powertrains, automatic transmissions and software systems, as well as key components, test verification, and calibration development.
5
4
Share

Where is the anti-theft box of Jianghuai Refine S4 located?

On the left side of the clutch pedal. Below is relevant information: 1. Vehicle anti-theft control box: The principle of the vehicle anti-theft control box is to install a remote-controlled computer mechanical lock at the gear shift mechanism of the vehicle transmission, controlled by a rolling code technology remote. The screw holes for installing the lock are designed with self-locking devices, and the installation location is hidden and secure, preventing code theft and disassembly. At the same time, the installation is very simple, independent, without drilling holes, and does not damage any original vehicle wiring, fuel lines, or steering control systems. 2. Precautions: Anti-theft systems are not omnipotent. Many cars now come pre-installed with an onboard computer anti-theft system from the factory. The engine will only start when the key chip data matches the pre-stored data in the onboard computer, which then instructs the relevant systems to begin operation. Vehicles equipped with an onboard computer anti-theft system do not require additional electronic anti-theft devices.
3
1
Share

What are the reasons for the high water temperature in Jianghuai Junling?

Cooling system leakage leading to insufficient coolant; The radiator fan is stuck or damaged and cannot perform the cooling function; Prolonged high-speed driving can easily cause the water temperature to be too high; Other common reasons include: broken fan belt, leakage in the radiator or water pipes, thermostat failure, oil leakage, water pump failure, etc. Below is relevant information: 1. Solutions: For vehicles experiencing high water temperature due to prolonged driving, you can pull over, turn on the hazard warning lights, and let the vehicle cool down naturally; A damaged radiator fan also requires finding the nearest repair shop for inspection as soon as possible. 2. Hazards of high water temperature: The normal water temperature of an engine is between 85-95 degrees Celsius. When the water temperature is too high, the viscosity of the engine oil becomes thinner, reducing its lubricating performance. High-speed components such as pistons and valves are prone to deformation, causing the engine to lose power. In severe cases, it can lead to cylinder scoring and crankshaft seizure, requiring major engine repairs.
16
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.