What are the dimensions of the Volkswagen Tharu?

1 Answers
DeMason
08/28/25 5:21am
The dimensions of the car are 4453×1841×1632mm, with a wheelbase of 2680mm. Below is the relevant introduction of the car: 1. In terms of interior, the new car features full leather seats, a panoramic sunroof, a 6.5-inch Chinese large screen, and configurations such as parking radar, automatic braking, keyless start, etc. In terms of power, the car is equipped with 1.4t and 2.0t engines, with maximum output power reaching 150 and 186 horsepower respectively, and maximum torque reaching 250 and 320 N·m, both meeting China's National 6 emission standards. The entire series is matched with a 7-speed dual-clutch transmission. 2. The headlights have a very full shape, using LED light sources and featuring daytime running lights. The lower turn signals also use LED light sources, and the fog lights at the very bottom come with a cornering light function. The LED low beams are equipped with lenses, creating a lighting effect full of a technological feel. The turn signals use a set of 10 LED lights, identical to those on the Touareg, while the fog lights use halogen light sources, with average lighting effects.
Was this review help?
8
2
Share
More Forum Discussions

What is the normal voltage display for a car charger?

The normal voltage display for a car charger is 12V. Car chargers have a rated voltage. The main purpose of a car charger is to provide convenience for car owners to charge their digital devices more easily while driving. Nowadays, cars are equipped with charging ports, usually featuring two USB interfaces, allowing simultaneous charging for two digital devices. Car chargers come with overload protection, short circuit protection, high-voltage input protection, and high-temperature protection, providing four layers of safety features, ensuring safe usage while driving. The built-in car charger is typically located on the car navigation system, with a well-designed USB interface that does not occupy too much space in the car. There are various types of chargers available on the market, including chargers for alkaline batteries, nickel-metal hydride batteries, nickel-cadmium batteries, etc.
11
0
Share

What are the reasons for the persistent illumination of the engine malfunction indicator light in the Sail?

The reasons for the illumination of the engine malfunction indicator light in the Sail mainly include the following 7 aspects: Sensor malfunction: The sensors referred to here include those for coolant temperature, crankshaft position, air flow, intake air temperature, oxygen sensors, etc. When these sensors are damaged, have poor contact, or experience signal interruption, the vehicle's ECU cannot accurately obtain engine data, which will trigger the engine malfunction light. Fuel quality issues: If fuel and engine oil are not added as required by the manufacturer, it may cause engine wear and lead to the illumination of the malfunction light. Poor combustion of the air-fuel mixture: Poor combustion can lead to engine carbon deposits or knocking. When detected by the oxygen sensor and reported to the ECU, the malfunction light will illuminate as a warning. Issues such as spark plug failure, ignition coil failure, fuel pump failure, or clogged fuel lines can all cause poor combustion of the engine's air-fuel mixture. Turbocharging problems: Issues with the intake boost pipes or turbocharger can also cause the engine malfunction light to illuminate. The most common issue is turbocharger damage, accompanied by symptoms such as oil leaks, excessive oil consumption, reduced power, metallic noises, or blue/black smoke from the exhaust. Intake problems: If there are issues with the vehicle's air intake, it may lead to clogged engine pipes, and in severe cases, the engine malfunction light will illuminate. A dirty air filter that is not cleaned regularly can cause intake problems. Exhaust problems: Exhaust system faults can also trigger the engine malfunction light. Common causes include issues with the rear oxygen sensor, catalytic converter, exhaust camshaft, or bearings. The catalytic converter is the most frequent culprit. The use of leaded gasoline, lead- or silicon-containing lubricant additives, physical damage to the catalytic converter, or faults in the engine's fuel supply system can all lead to catalytic converter failure. Anti-theft system malfunction: If the vehicle's electronic anti-theft system malfunctions or if the anti-theft controller is incompatible with the engine's electronic controller, the anti-theft system can prevent the engine from operating normally and cause the malfunction light to illuminate. If the engine malfunction light is illuminated, follow these steps: First, check whether the engine is running normally and if there are any issues such as shaking or black smoke. If so, avoid restarting the engine. Note: Do not restart the engine if the red warning light is on. If the engine can be started, turn it off and wait for 5-10 minutes. Without pressing the brake, press the start button once or turn the key halfway to the 'on' position without depressing the clutch. The vehicle will enter self-diagnosis mode after powering on. Wait for 5-10 seconds and observe whether the malfunction light on the dashboard turns off. If the malfunction light remains on, visit a service center as soon as possible. The service center can use a portable diagnostic tool to read the fault codes, identify the issue, and perform targeted repairs.
8
2
Share

Where is the Audi A4 air conditioning pressure sensor located?

Audi A4 air conditioning pressure sensor is located on the air conditioning pump. Below is relevant information about the sensors: 1. Interior temperature sensor: Usually installed under the instrument panel, it is a thermistor-type temperature sensor with negative temperature coefficient characteristics, used to provide the air conditioning electronic control unit with temperature signals from inside the vehicle cabin. 2. Exterior ambient temperature sensor: The exterior ambient temperature sensor is also a thermistor-type temperature sensor with negative temperature coefficient characteristics, typically installed on the lower side of the vehicle's front bumper, used to provide the air conditioning electronic control unit with temperature signals from outside the vehicle cabin.
10
5
Share

Will a decrease of 10 in the wheel ET value have any impact?

Reducing the wheel ET value by 10 will have certain effects on vehicle driving. Here is relevant information about wheel ET values: 1. Definition: The ET value of a wheel refers to the deviation between the mounting surface of the wheel and the centerline of the rim, also known as the offset (Off-set value). 2. Types of ET values: (1) Zero offset wheels – Indicate that the mounting surface of the wheel is located at the centerline of the rim. (2) Positive offset wheels – Indicate that the distance between the mounting surface and the center of the rim is towards the outer side. (3) Negative offset wheels – Indicate that the distance between the mounting surface and the center of the rim is towards the inner side.
20
0
Share

What Are the Standards for Adjusting Car Lights?

Car light adjustment standards involve parking the vehicle 7.6 meters away from a wall, turning on the headlights, and adjusting the light projection position based on their reflection on the wall. Below is a detailed introduction to headlight adjustment: 1. Vehicles with headlight height adjustment buttons: Simply adjust using the button. The location of the adjustment button varies by vehicle model, so it's recommended to refer to the vehicle's user manual for specific instructions. 2. Vehicles without headlight height adjustment buttons: Adjustment requires opening the engine hood and adjusting via the headlight assembly, known as mechanical adjustment. It's advisable to visit a 4S store or a professional auto repair shop for adjustment by a technician.
18
3
Share

What is the fault when the car air conditioner has no power?

Faults that cause the car air conditioner to have no power are as follows: 1. Compressor wear: Severe internal wear of the compressor leads to its inability to function properly. The compressor plays a crucial role in the air conditioning system, primarily compressing and delivering refrigerant, which causes it to operate at high speeds for extended periods, resulting in malfunction. 2. Lack of refrigerant in the car air conditioner: The compressor is used to compress and deliver refrigerant. If the refrigerant leaks, there is no refrigerant to compress or deliver, causing the compressor to fail. 3. Electrical system failure: Electrical system failures are a very common reason for the car air conditioner compressor not working properly. You can check if the circuit is unobstructed and inspect the temperature sensor and solenoid valve.
7
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.