What are the dimensions of the Verano?

How to Deactivate BMW Child Lock?

Toggle the child lock lever or rotate the child lock knob with a mechanical key, then close the door, and children inside the car will be unable to open the door (the child lock is now covered by the door). Insert the child lock key into the lock hole, rotate the child lock to the locked position, and this will prevent children from opening the door. To deactivate the child lock function, open the rear door from the outside and toggle the child lock in the opposite direction. Many taxis enable the child lock function on the left rear door to prevent passengers from exiting from that side, avoiding accidents where passing vehicles might collide with the door.

14

2

Share

What to Do When Your Car Battery Dies and Won't Start?

Locate the battery positions and the positive and negative terminals of both cars. First, connect the positive terminals of both cars with the red cable, then connect the negative terminals with the black cable. Press the clutch and release the handbrake. Put the gear in 1st or 2nd, keep the clutch pressed, and start pushing the car. When the speed reaches 5 km/h, release the clutch and press the accelerator. Simply attach the charger clips to the battery terminals and press the switch on the power bank. Prepare a tow rope and securely fasten the front and rear of both cars. Before starting, make sure to establish clear communication signals.

12

3

Share

How to Remove Car Wrap Film?

Use brush cleaner to remove it. Brush cleaner can be purchased at art supply stores. Dip a paper towel in a small amount of brush cleaner and wipe gently; it will come off easily. For small adhesive residues, an eraser is suitable, though patience is required. Initially, the area may turn black, but it will gradually clean up with continued rubbing. Moisten a paper towel with some alcohol, preferably industrial alcohol. If unavailable, medical alcohol will also work. Wipe slowly at first, then rub a few more times to clean thoroughly. Apply some nail polish remover to a paper towel and wipe patiently. After some time, the area will be clean.

6

4

Share

How to Deal with Slightly Deformed Motorcycle Wheel Rims?

If the deformation is slight, specialized testing equipment is needed to locate the exact position of the wheel rim deformation. Use heating tools to locally heat the deformed area of the wheel rim. Once the deformed area reaches a certain temperature, use wheel rim repair equipment to fix the deformation. After the repair is completed, test the wheel rim again to check for any remaining deformation. If none is found, the repair of the slightly deformed wheel rim is complete. If the wheel rim deformation is very severe, for safety reasons, it is necessary to replace the wheel rim directly.

15

4

Share

How to Repair a Dented Wheel Arch?

Prepare various lever tools along with professional lighting, repair hammers, specialized leveling pens, etc. Use the visual effect of light refraction to determine the position and extent of the dent. Apply the principle of leverage to release the tension at the dented area of the car body, allowing the surface 'entropy' value at the dent to reach its maximum, thereby restoring the dented area to its original state. Use repair hammers and leveling pens to fine-tune the raised marks on the car body, smoothing the surface to perfection. Check under lighting or sunlight; if no flaws are visible, the repair is considered successful.

14

4

Share

Should You Connect the Positive or Negative Terminal First When Jump-Starting a Car?

First, connect the positive terminals of both batteries, then connect the negative terminals. After starting the engine, disconnect the negative terminal first, followed by the positive terminal. If the order is incorrect, the risk of a short circuit increases significantly, although it may not always occur—careful operation might prevent it. This is because the entire vehicle body is connected to the negative terminal of the battery, meaning every metal component can be considered part of the negative terminal. Below is relevant information: Jump-starting requirements: If directly replacing the battery, the order of disconnecting the terminals is the opposite of jump-starting—disconnect the negative terminal first, then the positive terminal. During installation, connect the positive terminal first and the negative terminal last. This is to prevent a short circuit caused by a wrench touching the vehicle body during the process. Precautions: During routine maintenance, pay attention to the battery's condition. After parking, turn off all electrical devices in the car to avoid battery drain from prolonged inactivity, which may prevent the car from starting normally the next time.

11

2

Share

What are the dimensions of the Verano?

How to Deactivate BMW Child Lock?

What to Do When Your Car Battery Dies and Won't Start?

How to Remove Car Wrap Film?

How to Deal with Slightly Deformed Motorcycle Wheel Rims?

How to Repair a Dented Wheel Arch?

Should You Connect the Positive or Negative Terminal First When Jump-Starting a Car?

How to turn off the auto start-stop function on the new Santana?

What to Do When Crossing the Stop Line on a Yellow Light?

What are the methods to eliminate odors inside a car?

How to adjust the turn signal sound on a BMW 5 Series?