What are the dimensions of the Highlander?

2 Answers
SanAsher
07/28/25 9:30pm
The dimensions of the Highlander are 4890 mm in length, 1925 mm in width, and 1720 mm in height, with a wheelbase of 2790 mm. The Highlander is a mid-size SUV produced by Toyota, featuring a fuel tank capacity of 72 liters. It is equipped with a 3.5-liter V6 engine that delivers up to 201 kW of power, paired with a stepped 5-speed automatic transmission with manual mode, a four-wheel drive system, and a newly developed suspension system. The Highlander boasts a spacious body and an innovative, roomy interior. It comes with 9-inch large-diameter wheels and utilizes a front MacPherson strut and rear double-wishbone suspension system.
Was this review help?
19
5
Share
BenjaminAnn
08/12/25 2:07am
I've been driving the Highlander for over two years now. This vehicle is quite sizable, measuring approximately 4965mm in length, 1930mm in width, and 1750mm in height, with a wheelbase of 2850mm. The spacious interior is particularly noticeable, especially when seating three people in the back row without feeling cramped. However, parking in the city center can be challenging due to its nearly two-meter width—finding a suitable spot requires extra effort, and I always have to be careful. Turning also demands more attention. Overall, the size design is practical and well-suited for long-distance travel, with a trunk capable of accommodating large suitcases. That said, I'd recommend that beginners practice their reversing skills more.
Was this review help?
17
1
Share
Expand All
More Forum Discussions

Reasons for abnormal noise in the clutch pedal of Wuling Hongguang S

The reasons for abnormal noise in the clutch pedal of Wuling Hongguang S are as follows: 1. Severe wear or lack of oil in the release bearing, or the bearing return spring being too soft, broken, or detached; 2. Wear and looseness between the release lever bracket pin and the hole; 3. The pedal return spring being too soft, detached, or broken; 4. Loose rivets on the driven disc, fractured steel plates, or broken damping springs. Additional information: Fault diagnosis and troubleshooting: 1. Press the clutch pedal to make the release lever contact the release bearing. If a "grinding" sound is heard, it indicates noise from the release bearing. If the noise persists after lubrication, the bearing is worn or damaged. 2. After releasing the clutch pedal, increase the engine speed. If there is an intermittent impact sound, it indicates noise from the release bearing sliding back and forth. Remove the clutch bottom cover and check if the release bearing return spring is broken or detached. 3. If noise occurs when the pedal is fully depressed and disappears when released, it indicates wear and looseness between the intermediate pressure plate drive pin and the pin hole of the clutch. 4. If noise occurs when the clutch just engages or disengages while repeatedly pressing the pedal, it indicates wear and looseness between the release lever and the bracket pin and hole, or loose and exposed rivets. 5. If noise occurs when the engine starts and disappears when the pedal is lifted, it indicates burning or damage to the release bearing.
13
5
Share

Is It Normal for an Automatic Car to Make Abnormal Noises When Shifting to P Gear?

It is not normal for an automatic car to make abnormal noises when shifting to P gear. The noise could be the sound of the car unlocking, and the driving method should be adjusted promptly. Below are detailed introductions about automatic cars: 1. Overview: An automatic car generally refers to a car that uses an automatic transmission (AT) to adjust the speed. While driving, the control system of the automatic transmission automatically selects the appropriate gear based on the engine's speed and load, replacing the driver's subjective judgment of timing and gear shifting operations. In simple terms, an automatic car is a "fool-proof car." 2. Transmission Types: There are mainly two types of automatic transmissions used in cars. One is the stepped automatic transmission, and the other is the continuously variable transmission (CVT). The most commonly used in passenger cars is the mechanical continuously variable transmission.
14
3
Share

How to Shift Gears Without Stalling the Engine?

Here are the methods to shift gears without stalling the engine: 1. Pay attention to the shifting RPM: During driving, the RPM for both upshifting and downshifting should be within the specified range. Failure to follow standard procedures can easily lead to damage to the engine and transmission. 2. Speed up the shifting process: This prevents the engine from losing power, as the RPM drops particularly quickly. The difference in speed between the engine RPM and the clutch plate RPM helps make gear shifts smoother. 3. Utilize the clutch's semi-engaged state: By speeding up the shifting process and gently pressing the accelerator, using the clutch's semi-engaged state during gear shifts makes the vehicle's power output smoother. This applies to both upshifting and downshifting. While driving, avoid sudden acceleration or braking.
8
3
Share

Reasons why the Wuling Hongguang Mini won't start or ignite

The reasons why the Wuling Hongguang Mini won't start or ignite are as follows: 1. Circuit or electronic failure: The occurrence is very sudden, with no prior signs. Circuit failures include blown fuses, open high-voltage coils, open low-voltage circuits, detached central ignition wires, leaking distributor rotors, and damaged spark plugs; electronic failures mainly refer to the central computer control board losing functionality. 2. Fuel system failure: Stalling caused by fuel system failures often comes with symptoms like weak engine power and a spongy accelerator pedal. Possible fuel system failure points include malfunctioning fuel pumps, blocked fuel lines, clogged fuel filters, failed carburetors, damaged injectors, etc. Sometimes, the fuel tank may be empty without the owner realizing it. 3. Mechanical failure: Common mechanical failures include broken timing belts (or chains), cylinder leaks with no pressure, etc.
8
0
Share

What is the size of the Wuling Hongguang wiper?

Wuling Hongguang wiper size is 22-16 inches. Here is some related information about wipers: 1. Introduction to wipers: Wipers, also known as windshield wipers, are devices used to remove raindrops and dust attached to the vehicle's windshield. 2. Function of wipers: To improve the driver's visibility and increase driving safety. The wiper consists of a motor, reducer, four-bar linkage, wiper arm spindle, wiper blade assembly, etc. 3. Wiper cleaning: Remove debris and dirt from the wiper rubber strip. It is best to rinse with water first, then wipe the wiper strip with a cotton cloth or tissue.
2
3
Share

Does the ETC card application require the vehicle to be under one's own name?

It is possible to apply for an ETC even if you are not the vehicle owner. According to the "Implementation Plan for Accelerating the Application Service of Electronic Non-stop Toll Collection on Highways" issued by the Ministry of Transport, the original valid ID card of the vehicle owner, the original and a copy of the vehicle registration certificate, and the page of the registration certificate showing the most recent annual inspection stamp are required. If applying on behalf of someone else, the original valid ID card of the agent is also needed. If applying for ETC through major bank branches, you will also need to prepare a debit card or credit card from the corresponding bank. Some banks only support ETC binding with credit cards, while others may require freezing a portion of the amount as a security deposit when binding ETC with a debit card. ETC Deduction Principle: There will be one or more ETC lanes on highways. Through microwave dedicated short-range communication between the vehicle-mounted electronic tag installed on the windshield and the microwave antenna in the ETC lane of the toll station, and using computer networking technology for backend settlement with the bank, the purpose of paying tolls without stopping at the toll station is achieved. All this is based on the principle of passing first and deducting fees later. Benefits of Installing ETC: Time-saving: Eliminates the hassle of waiting in line; Green and eco-friendly: Low-carbon, vehicles pass through toll stations without stopping, reducing noise and exhaust emissions, and minimizing pollution; Cost-saving: Reduces vehicle start-up and braking frequency, lowering wear and fuel consumption; Efficiency improvement: Theoretically, ETC lanes can improve vehicle passing efficiency by 2-3 times, making traditional ETC faster, more advanced, and high-tech. Compared to license plate payment, ETC technology is more mature and advantageous. More policy support: The State Council clearly stated in the "13th Five-Year Plan for the Development of a Modern Comprehensive Transportation System" that "by 2020, the interoperability of transportation cards in key city clusters will be basically achieved, and the proportion of vehicles equipped with ETC will be significantly increased." It also set a target in the main indicators of the "13th Five-Year" comprehensive transportation development: "by 2020, the ETC usage rate for road passenger vehicles will reach 50%." More future possibilities: In addition to continuously improving the convenience of ETC installation and usage and the ETC usage rate for passenger vehicles, the future will also promote the use of ETC for trucks and explore the deep integration of the ETC system with smart transportation development directions such as vehicle-to-vehicle communication and vehicle-road coordination, providing comprehensive travel services for vehicle owners. This means more application scenarios will support ETC applications. ETC Usage Notes: The ETC transaction sensing area is 8 meters. When encountering a stopped vehicle ahead, to prevent the vehicle ahead from having a faulty ETC device or no ETC device at all, maintain a distance of more than 10 meters to avoid automatic sensing and paying for the vehicle ahead. The ETC lane passing recognition speed is 20 km/h. If the speed is too fast, the vehicle device information cannot be read, leading to deduction failure. Unauthorized removal or movement of the OBU device, or detachment or loosening of the ETC electronic tag, will cause the electronic tag to fail. It can be sent to the bank where the ETC card was issued or the highway service office for testing. Non-human-induced loosening or detachment only requires reactivation. When binding ETC with a debit card, insufficient balance will also cause deduction failure. Follow the guidance of on-site staff to use the manual MTC lane and pass by cash or card. Excessive thickness of the car windshield can cause poor sensing. This is especially important for vehicles that have had their windshields replaced after accidents or for those who have modified their front windshields.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.