What are the differences between Toyota Reiz 2.5V and 2.5S?

How to adjust the windshield washer spray of Lavida?

The method to adjust the windshield washer spray of Lavida is: 1. Locate the windshield washer nozzle on the plastic cover below the front windshield, try spraying the washer fluid to check if the water column is within a reasonable area; 2. If not suitable, find the position of the spray nozzle and use a prepared needle to insert into the nozzle for fine-tuning. Taking the 2019 Lavida as an example, it belongs to the compact car category, with body dimensions of: length 4613mm, width 1765mm, height 1460mm, a wheelbase of 2610mm, and a curb weight of 1210kg. The 2019 Lavida features a MacPherson strut front suspension and a torsion beam rear suspension. It is equipped with a 1.5L naturally aspirated engine, producing a maximum horsepower of 112PS, a maximum power of 82kW, and a maximum torque of 145Nm, paired with a 5-speed manual transmission.

13

5

Share

Should the Clutch Be Pressed When Braking?

It is not always necessary to press the clutch when braking. The specific situations are as follows: 1. Automatic transmission cars do not have a clutch pedal, so you can directly press the brake. 2. When driving at high speed or normal speed, if the intention is only to slow down, there is no need to press the clutch. 3. When taking a curve, first press the brake to slow down. After the curve, if there are no obstacles, there is no need to press the clutch; release the brake and press the accelerator to speed up. If there is an obstacle right after the curve, then press the clutch and shift to a lower gear. 4. When going down a long or steep slope, there is no need to press the clutch; use the engine's traction for braking. 5. When intending to stop, first press the brake to reduce the speed, then press the clutch. 6. In heavy traffic with frequent stops and short following distances, press both the clutch and brake simultaneously each time you brake.

7

5

Share

What are the causes of Honda hybrid transmission failure?

There are many reasons why the transmission warning light is on but the vehicle is driving normally, such as a malfunction in the transmission control module, a failure in the transmission shift solenoid valve, internal gear wear in the transmission, or a malfunction in the transmission's internal friction plates. The specific cause can be determined by using a diagnostic tool at a repair shop to read the fault codes, followed by identifying the fault point based on these codes. Below is relevant information: 1. Transmission: The transmission is a very important component of a vehicle. It can change the transmission ratio and expand the torque and speed of the drive wheels. With the development of modern technology, transmissions have been upgraded from the original manual transmissions to continuously variable transmissions, and from non-synchronized to synchronized, making operation increasingly convenient. 2. Main functions: Changing the transmission ratio to expand the range of torque and speed variations of the drive wheels to adapt to frequently changing driving conditions, while allowing the engine to operate under favorable conditions; enabling the vehicle to reverse while maintaining the same engine rotation direction.

12

1

Share

Why is the car weak to start?

Car starting weakness may be caused by: 1. The battery's poor charging capacity due to long-term under-voltage, lack of electrolyte, or overcharging; 2. Excessive wear of internal copper sleeves, rotor scraping, or burnt contacts in the engagement switch of the starter motor after prolonged use; 3. Wear of the internal regulator and carbon brushes in the generator. The steps to start a manual transmission car are: 1. Fully depress the clutch pedal; 2. Push the gear lever to engage first gear; 3. Lightly press the turn signal lever downward to activate the left turn signal, alerting vehicles in front and behind; 4. Press the horn button to alert pedestrians in front of the vehicle of the impending start; 5. Release the vehicle's handbrake; 6. Lift the left foot until the clutch reaches the semi-engaged state, causing the vehicle to vibrate slightly; 7. As the vehicle begins to move, release the clutch and gently press the accelerator.

10

4

Share

What Are the Reasons for the Tire Pressure Indicator Light Staying On When the Tire Pressure Is Normal?

When the tire pressure is normal but the indicator light remains on, the possible reasons are: 1. The tire pressure was previously too low, and although it has been replenished, the tire pressure monitoring system has not been reset, retaining the original fault code. 2. The tire pressure sensor is damaged or there is a system malfunction. The hazards of low tire pressure include: 1. Shortening the lifespan of the tires. 2. Increasing the friction coefficient with the road surface. 3. Creating factors that are detrimental to driving safety, such as making the vehicle prone to veering off course. The hazards of high tire pressure include: 1. Reducing the tire's friction and adhesion, affecting braking performance. 2. Causing steering wheel vibration and veering, reducing driving comfort. 3. Accelerating localized wear of the tread pattern in the center of the tire, leading to a shorter tire lifespan. 4. Increasing vehicle vibration, which indirectly affects the lifespan of other components.

17

0

Share

What is the correct method for connecting jumper cables to a car?

The correct method for connecting jumper cables to a car is: 1. Take out one positive and one negative jumper cable; 2. Remove the clips to open the battery protective cover, exposing the battery's positive and negative terminals; 3. Take one jumper cable, connect one end to the positive terminal of the dead battery and the other end to the positive terminal of the live battery; 4. Take the other jumper cable, connect one end to the negative terminal of the live battery, and then connect the other end to the engine block or body of the dead vehicle, ensuring to connect negative to negative. The method for jump-starting a battery is: 1. Park the live vehicle next to the dead vehicle, with the front ends facing each other and close; 2. Open the hoods of both vehicles and take out the charging clamps; 3. Locate the batteries of both vehicles, attach the negative clamps to the negative terminals of both batteries, and the positive clamps to the positive terminals of both batteries; 4. Start the live vehicle, charge for a few minutes, then start the dead vehicle to get it running.

19

1

Share

What are the differences between Toyota Reiz 2.5V and 2.5S?

How to adjust the windshield washer spray of Lavida?

Should the Clutch Be Pressed When Braking?

What are the causes of Honda hybrid transmission failure?

Why is the car weak to start?

What Are the Reasons for the Tire Pressure Indicator Light Staying On When the Tire Pressure Is Normal?

What is the correct method for connecting jumper cables to a car?

Does Idling Consume More Fuel?

What does 'Da Ben Che' mean and is it worth buying?

Should vehicle inspection be done at the DMV or inspection station?

Do I Need to Collect the Annual Inspection Sticker for a Seven-Year-Old Car?