What are the differences between the Mercedes-Benz GLE43 and GLE400?

1 Answers
WyattLynn
07/29/25 5:08pm
Here are the main differences between the Mercedes-Benz GLE43 and GLE400: 1. In terms of configuration, these two models are basically similar. 2. In terms of power, the GLE43 has stronger performance. Although both use a 3.0T turbocharged engine, the GLE43's engine is better tuned, as it belongs to the AMG series. 3. In terms of appearance, the Mercedes-Benz GLE400 AMG has a more rounded design, with the front face still adopting the Mercedes-Benz family design style, offering excellent visual appeal. 4. In terms of configuration, both the GLE400 and GLE43 AMG use a 3.0T twin-turbocharged V6 gasoline engine, with a maximum power output of 367 horsepower and a maximum torque of 520 Nm. 5. The transmissions are different: the GLE43 AMG uses a 9G-TRONIC transmission, while the GLE400 uses the previous generation's 9G-TRONIC transmission. The GLE43 AMG accelerates from 0 to 100 km/h 0.6 seconds faster than the GLE400.
Was this review help?
11
0
Share
More Forum Discussions

Is it necessary to install door sill protectors on cars?

The door sill protectors are not necessary to install on cars. Here is more information about car door sill protectors: 1. Function of door sill protectors: The main functions of car door sill protectors are to protect the car body and decorate the door sill area. 2. Disadvantages of door sill protectors: Aftermarket door sill protectors can easily cause friction with the car door, and since they are attached with strong adhesive, they may fall off after some time. 3. Precautions for installing door sill protectors: Before installing door sill protectors, it is necessary to clean the installation area, ensuring the paint surface is dry and clean. After pasting, pressure should be applied to ensure full contact of the adhesive surface, and a hair dryer can also be used for heating to ensure complete fusion of the adhesive surface.
20
5
Share

How to Lift the Wiper Blades on the Tiguan?

During the operation of the wiper blades, disconnect the vehicle's power supply. At this point, the wiper blades will stop in the center of the windshield due to the loss of power supply, allowing them to be lifted. Note: The wiper blades operate quickly, so you may need to try several times. The rebound force of the wiper blades is strong, so be careful not to damage the windshield. The specific steps are as follows: 1. Press the vehicle's one-touch start button to turn on the power. 2. The dashboard lights will illuminate, indicating the power is on. 3. Pull the wiper switch on the Tiguan. 4. Turn off the power while the Tiguan's wipers are operating. 5. Follow the above steps to position the Tiguan's wiper blades in the center.
7
4
Share

How Often Should the Gear Oil of a Scooter Be Changed?

Scooter gear oil generally needs to be changed every 2,000-3,000 kilometers. For higher-end models, it can be changed every 5,000 kilometers or more. Unlike engine oil, as long as there is oil in the gearbox, the bearings and gears inside will be fine, since the gearbox does not generate much heat and only requires lubrication. Additional Information: 1. Gear oil is a high-viscosity lubricant specifically designed to protect power transmission components, often characterized by a strong sulfur odor. 2. Vehicle gear oil is classified by performance and viscosity. Currently, the API (American Petroleum Institute) performance classification and U.S. military gear oil specifications are widely adopted worldwide. Most manual transmission lubricants and differentials use hypoid gear oil, which contains extreme pressure (EP) additives and anti-wear additives to handle the action of hypoid bevel gears.
3
5
Share

Where is the crankshaft timing mark on the Haval H6?

The crankshaft timing mark on the Haval H6 is the arrow on the crankshaft pulley. Below is relevant information: 1. The lower part of the cylinder block where the crankshaft is installed is called the crankcase, which is divided into the upper crankcase and the lower crankcase. The upper crankcase is cast as one piece with the cylinder block, while the lower crankcase is used to store lubricating oil and seal the upper crankcase, hence it is also known as the oil pan. 2. The crankcase is one of the most important components in the engine. It bears the force transmitted by the connecting rod and converts it into torque, which is then output through the crankshaft to drive other engine accessories. The crankcase is subjected to the combined effects of centrifugal force from rotating masses, periodic gas inertial forces, and reciprocating inertial forces, causing the crankshaft to bear bending and torsional loads.
16
4
Share

What is the tire model of the Hyundai ix35?

The tire model of the Hyundai ix35 is 225/60R17, and it comes standard with Hankook OPTIMOH426 series tires. Here are some relevant details about the Hyundai ix35: 1. Body dimensions: The length, width, and height are 4500mm, 1850mm, and 1715mm respectively. The wheelbase is 2640mm. 2. Powertrain: Equipped with a 1.4T 140-horsepower 4-cylinder G4LD engine, using 92-octane fuel, and paired with a 7-speed dual-clutch transmission. 3. Chassis: The drivetrain is front-wheel drive, with a front suspension of MacPherson strut independent suspension and a rear suspension of multi-link independent suspension.
20
2
Share

Should You Press the Clutch When Shifting Gears?

Manual transmission cars require pressing the clutch. Failing to press the clutch when shifting gears can easily damage the gears and harm the transmission. Additional information: 1. If the clutch is not pressed: The engine and the first shaft of the transmission cannot be completely separated, leading to intermittent engagement during transmission, which can cause abnormal noises during shifting and significantly affect the car. 2. Proper gear engagement: When shifting gears in a manual transmission car, it is also important to ensure that the gear is fully engaged. Some drivers shift gears carelessly, possibly lifting the clutch hastily before the gear is properly engaged, which can also damage the transmission. 3. Fully depress the clutch: (1) When shifting gears, the clutch must be fully depressed to ensure successful shifting before releasing it. (2) The gear must be properly engaged, and the driver should be familiar with the shifting method for each gear.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.