What are the differences between the Mercedes-Benz 2.5t and 3.0t?

1 Answers
RubyDella
07/29/25 12:37pm
Mercedes-Benz 2.5t and 3.0t differences are: 1. Different body dimensions: The Mercedes-Benz 2.5t has a body length, width, and height of 4813mm, 1951mm, and 1761mm respectively; the 3.0t has dimensions of 4941mm, 2018mm, and 1782mm. 2. Different maximum horsepower: The Mercedes-Benz GLE 2.5t has a maximum horsepower of 333ps, while the 3.0t has a maximum horsepower of 367ps. Both the Mercedes-Benz 2.5t and 3.0t are equipped with a 9-speed automatic transmission; the front suspension is a double-wishbone independent suspension, and the rear suspension is a multi-link independent suspension.
Was this review help?
3
1
Share
More Forum Discussions

How to Remove the Outer Door Handle of Haval H6?

Haval H6 outer door handle removal method: 1. Remove the door trim panel, then remove the door protective film by peeling off the upper left corner of the film; 2. Reach inside the door cavity and disconnect the clip connecting the handle to the door lock; 3. Remove the door handle screw from the side of the door, and finally take off the door handle from the outside. Taking the 2021 Haval H6 1.5T Manual Urban Edition as an example: its dimensions are 4615mm in length, 1860mm in width, and 1720mm in height, with a wheelbase of 2680mm. The engine has a maximum power of 110 kW, a maximum torque of 210 N·m, and a maximum torque speed range of 1800 to 4400 rpm.
9
3
Share

How to Eliminate the Exhaust Controller Malfunction Light?

Exhaust Controller Malfunction Light Elimination Methods: Start and turn off the car three times in a row, or disconnect the negative terminal of the engine battery, wait for 30 seconds, and then reconnect it. If the light does not go off, it is recommended to promptly visit a 4S shop for inspection and repair. Reasons for the Exhaust Controller Malfunction Light: 1. False Fault: A fault code is reported but the system operates normally, which may be due to an operation exceeding the computer's control range; 2. Minor Fault: Such as an intake pressure sensor malfunction; 3. Major Fault: Such as an oxygen sensor issue. The exhaust system refers to the system that collects and discharges waste gases, including the exhaust manifold, exhaust pipe, muffler, tailpipe, and resonator.
5
2
Share

Should You Turn on Headlights and Fog Lights When Temporarily Parking in Snow?

When temporarily parking in snow, you should not turn on the headlights and fog lights. Instead, you should activate the hazard warning flashers, clearance lights, and rear position lights. Fog lights have strong penetration, and using them in snowy conditions can cause glare due to reflection, which may affect driving safety. Hazard warning flashers are signal lights that alert other vehicles and pedestrians to the fact that this vehicle is experiencing a special situation. Clearance lights are warning lights located at the front and rear edges of the vehicle, used to alert other vehicles. Rear position lights, commonly known as small lights, primarily indicate the presence and approximate width of the vehicle, making it easier for other vehicles to judge during encounters and overtaking.
2
2
Share

How to Correct Steering Wheel Timing for Reversing into the Garage in Subject 2?

Correcting the steering wheel timing when reversing into the garage in Subject 2 is quite simple: if you steer too early, correct early; if you steer too late, correct late. It's better to steer early than late! Reversing into the garage is the most challenging part of Subject 2, and every driving school emphasizes it as a key training item. Many students don't fully understand the reference points, often leading to steering too early or too late. Steering too early or late isn't the issue—the real problem is not knowing how to correct it. This article shares relevant correction methods: First, for steering too early, take left-side reversing as an example. If you steer too early and don't correct in time, the left rear wheel will press against the upper left corner of the garage. The correction method is: correct early by straightening the car's turning arc, then promptly observe the distance between the car body and the left garage corner through the left mirror. When the distance is about 30 cm, turn the steering wheel back half a turn to return to the normal path. Second, for steering too late, again using left-side reversing as an example, steering too late usually causes the right rear wheel to press against the upper right corner of the garage. If you steer way too late, it's irreparable. If it's just slightly late, correction is still possible by delaying the half-turn correction—essentially "correcting late." When observing through the left mirror, if you've steered slightly late, the distance between the car body and the left garage corner will exceed 30 cm. Don’t rush to correct; instead, continue reversing and correct a bit later to extend the turning arc. Keep observing the left mirror and the alignment between the car body and the garage line, waiting for the right moment to straighten the wheels.
14
2
Share

Detailed Explanation of Step-by-Step Points for Exiting Parallel Parking in Subject 2?

Step 1, Determining the Position for Parallel Parking: When performing parallel parking, first drive the car into the designated starting position. The body of the car should maintain a distance of 30 to 50 centimeters from the roadside line. The right 1/3 of the hood should align with the right line. Keep driving straight, and when the lower edge of the left rearview mirror passes the starting line of the test area—that is, when your shoulder is level with the control line—press the clutch and brake to stop. Step 2, Key Points for Parallel Parking: 1. After hearing the voice prompt, turn on the right turn signal. Shift into reverse gear and slowly back up. Observe the left rearview mirror, using its lower edge to align with the control line ahead. When they coincide, look at the right rearview mirror. When the right rear wheel of the car aligns with the horizontal line at the front of the parking space, quickly turn the steering wheel fully to the right. 2. Continue reversing slowly while observing the left rearview mirror. When you see the innermost corner of the parking space, quickly turn the steering wheel two full turns to the left. 3. Keep reversing slowly, and when the left rear wheel is about to touch the parking space line, turn the steering wheel fully to the left. Then observe the left rearview mirror. Stop when the car body is parallel to the parking space line. Tips for Exiting Parallel Parking: 1. When exiting, first turn on the left turn signal. Press the clutch, shift into first gear, and slowly move forward. When the right front corner of the hood aligns with the roadside line on the right, straighten the steering wheel and continue forward. 2. When the left 1/3 of the hood aligns with the roadside line on the left, turn the steering wheel one full turn to the right to maneuver the car around the parking space corner and exit the spot. Once the car body is parallel to the road, straighten the steering wheel to the left and exit the parallel parking test area to proceed to the next test item.
16
2
Share

What is the fuel consumption per 100 kilometers for the Mustang?

The fuel consumption per 100 kilometers for the Mustang is 12.2L. 1. Power: The Mustang is equipped with a 5.4L V8 aluminum engine, with a maximum output power of 430 horsepower. You can choose between a 6-speed manual or a 3-speed C4 racing automatic transmission according to your preference. 2. Exterior colors: The Mustang offers more color options, including red, blue, and white. Users can also choose a new body pattern paint package for decoration. 3. Interior: All plastic parts in the Mustang have a soft texture. The dashboard has been completely changed to aluminum alloy panels, and the silver parts on the steering wheel are also made of metal. The strong metallic feel complements the muscular exterior design, while meeting modern aesthetic standards.
4
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.