What are the differences between the Lavida 1.5 and 1.4?

1 Answers
VanHenry
07/29/25 11:56pm
Here are the differences between the Lavida 1.5 and 1.4: Power: The 1.4T engine has lower power output than the 1.5T. Fuel consumption: The difference is minimal. However, it's important to note that the 1.5L model uses 92 octane gasoline, while the 1.4T model requires 95 octane or higher. In the long run, the 1.5L naturally aspirated model has lower operating costs. Maintenance: The maintenance costs for the 1.4T model are definitely higher than the 1.5L model. Regarding engine oil specifications and quality, the 1.4T turbocharged model has higher requirements for oil quality and typically requires full synthetic oil.
Was this review help?
2
5
Share
More Forum Discussions

How to turn off the air conditioning in Changan CS35?

The air conditioning switch of Changan CS35 is located below the central control screen, labeled as the OFF button. To turn on the air conditioning, rotate the OFF button to the right towards the red mark. To turn it off, rotate it to the left towards the blue mark.
8
0
Share

What are the 7-seater automatic transmission cars?

7-seater automatic transmission cars include Mitsubishi Outlander, Honda Odyssey, Buick GL8, Ford Edge, GAC Trumpchi GM8, Chevrolet Captiva, Baojun 730, Volvo XC90, Nissan Patrol, Kia Sorento, Hyundai Grandeur, Infiniti QX60, etc. Below is an introduction to the Outlander: Exterior: The Outlander adopts the Dynamic-Shield design language of the Mitsubishi family, with a massive X-shaped front grille that gives a robust impression, especially with the black-painted front grille, exuding a sporty vibe. Simple lines outline a beautiful silhouette, particularly the waistline that runs from the front to the rear of the car, highlighting the vehicle's sense of power. Configuration: The Outlander features a traditional T-shaped center console layout, specifically designed to lean towards the driver's side, allowing the driver to reach controls without much adjustment during daily driving. Additionally, apart from the large screen on the center console, most operations can be directly selected via functional buttons, complemented by the multifunction steering wheel, enabling the driver to perform blind operations once familiar. The center console is covered with soft plastic, offering a good tactile feel and facilitating daily cleaning.
11
2
Share

How to Save Yourself When the Brakes Fail

After the brakes fail, in addition to solving the problem of slowing down, you also need to pay attention to the surrounding vehicles. Using hazard lights and the horn can alert nearby vehicles. Pressing the brake pedal repeatedly several times will apply pressure to the air pressure braking system in the oil pipe, increasing the chance of restoring braking force. If the braking force cannot be restored after multiple attempts, you will need to use the handbrake to slow down the vehicle.
15
4
Share

How to Open a Car Key to Replace the Battery?

Insert a small screwdriver into the side slot near the key blade and push the screwdriver firmly toward the key blade. Separate the key blade from the chip case, then insert a flat-head screwdriver into the groove on the side of the chip case and twist to release the housing latch. Next, insert the flat-head screwdriver into the groove at the top of the chip case and twist to release the housing latch for replacement.
3
4
Share

How to Replace the Battery in a Skoda Octavia Key

Open the key, apply force along the direction of the arrow to open one corner of the battery cover, then use force to open the other corner of the battery cover, and you can lift the battery cover off. You will see the exposed button battery. Apply force diagonally downward to pop the battery out. To reinstall the battery, apply force diagonally downward to snap the battery into the key's battery compartment, paying attention to the battery's orientation (positive and negative sides).
2
3
Share

How to Adjust the Valves on a Three-Cylinder Engine?

Rotate the crankshaft to determine the engine's firing order. Turn the crankshaft to reach the compression top dead center of the third cylinder. When the third cylinder is at compression top dead center and the other valves are closed, adjust the valves. After completing the adjustment, rotate the crankshaft 360 degrees to reach the exhaust top dead center of the third cylinder.
4
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.