What are the differences between the 8.5th generation Accord and the 8th generation?

How to Use Rearview Mirrors for Reversing?

It is necessary to adjust the right rearview mirror to ensure that the top of the mirror can see the rear door handle while keeping the front door handle in the center of the mirror. Note that the car body should occupy 1/4 of the mirror area. For the left rearview mirror, ensure that the left rear wheel is visible when parking sideways, and also observe the distance between the right front of the vehicle on the left side of the parking space and the left end of your car's rear bumper through the left exterior mirror. There are three key reversing techniques: 1. Adjust the position between the car body and the corner of the parking space: Check the relationship between the car body and the corner of the parking space in advance. Observe through the rearview mirror to predict whether the car body will be too close or too far from the corner at the current angle, then steer to correct it. Ideally, maintain a distance of 30 cm between the car body and the corner. 2. Correct the car body inside the parking space: After the rear half of the car enters the parking space, steer to adjust. Observe the left and right rearview mirrors to determine which side the front of the car is tilting toward and which side the rear is tilting toward, then steer toward the tilting side to correct the car body. 3. Find the stopping point: Judge when to stop by observing the relationship between the left rearview mirror and the boundary line. When the left rearview mirror covers the boundary line, immediately press the clutch to stop.

14

1

Share

What grade of gasoline should a BMW X3 use?

BMW X3 should use 95-octane gasoline, as recommended in the vehicle's official user manual. In addition to checking the appropriate gasoline grade in the user manual, you can also find it on the fuel tank cap, which will be clearly marked. Generally, the gasoline grade can also be determined based on the engine's compression ratio. Vehicles with an engine compression ratio between 8.6-9.9 should use 92-octane gasoline, while those with a compression ratio between 10.0-11.5 should use 95-octane gasoline. If the compression ratio is higher, 98-octane gasoline is recommended. However, with the application of new technologies, the gasoline grade cannot be solely determined by the compression ratio. A high compression ratio can also be adjusted to use lower-octane gasoline, as other factors such as ignition timing, turbocharging technology, and Atkinson cycle technology also play a role. Generally, the higher the gasoline grade, the higher the octane number and the better the anti-knock performance. 92-octane gasoline contains 92% isooctane and 8% n-heptane, while 95-octane gasoline contains 95% isooctane and 5% n-heptane. If you occasionally use the wrong gasoline grade in a BMW X3, simply switch back to the correct grade after consumption. However, long-term use of the wrong gasoline grade can have the following effects: For vehicles recommended to use lower-octane gasoline, using higher-octane gasoline will not cause damage, but the increase in octane number will change the fuel's ignition point, leading to delayed combustion in the engine. This results in reduced engine power and thermal efficiency, with the actual feedback being poorer performance. For vehicles recommended to use higher-octane gasoline, using lower-octane gasoline can cause engine knocking. Due to the significantly lower octane number, the gasoline's ignition point decreases, causing premature ignition during the compression stroke. If combustion occurs before the spark plug ignites, resistance will arise during the upward stroke. This resistance makes the engine run very unstably. Mild knocking only increases noise without significant engine damage, but noticeable knocking indicates severe engine conditions, affecting not only driving stability but also causing abnormal wear on pistons and cylinders, and in severe cases, cylinder scoring.

2

0

Share

Should I Buy the Geely Xingyue in Gray or Silver?

Choosing gray would be better as it is more resistant to dirt and offers better texture. Here are some details about the Geely Xingyue: 1. Introduction One: The Geely Xingyue is a compact sedan under the Geely brand. The dimensions of this car are 4785 mm in length, 1869 mm in width, and 1469 mm in height, with a wheelbase of 2800 mm. The Geely Xingyue is a four-door, five-seater sedan, and it comes standard with a 2.0-liter turbocharged four-cylinder engine. 2. Introduction Two: The 2.0-liter turbocharged engine of the Geely Xingyue delivers 190 horsepower. This engine can output maximum power at 4700 rpm, with a maximum torque of 300 Nm and a torque range of 1400 to 4000 rpm. The engine features direct fuel injection technology and uses an aluminum alloy cylinder head and block, which reduces the engine's weight, thereby improving fuel economy and handling. The engine is paired with a 7-speed dual-clutch transmission. 3. Introduction Three: The front suspension of the Geely Xingyue uses a MacPherson independent suspension, while the rear suspension employs a multi-link independent suspension. The multi-link suspension enhances the wheel's grip, improving the car's handling and ride comfort. The multi-link suspension is an improvement over the double-wishbone suspension, replacing the two wishbones with separate links.

18

2

Share

What causes insufficient oil pressure in the Volkswagen EA888 engine?

Insufficient oil pressure in the Volkswagen EA888 engine is related to the oil pressure sensor located next to the oil filter, with one high-pressure and one low-pressure sensor. Low oil levels can lead to insufficient pressure. It's often difficult to determine whether the oil needs changing just by visual inspection or touch. Under normal driving conditions, if synthetic oil is used, it generally can be changed every 10,000 kilometers. When selecting engine oil, pay attention to the following four key factors: 1. Key Factor One: Choose oil based on the engine's requirements. There's no need to use overly advanced oil in engines with lower requirements, nor should lower-grade oil be used in engines with higher requirements. 2. Key Factor Two: Multi-grade oil is preferable as it is economical, long-lasting, and efficient, providing better protection for the engine. Due to the characteristics of multi-grade oil, it may appear darker or show lower oil pressure compared to conventional oil, which is normal. 3. Key Factor Three: Some domestic brand oils are of quite good quality and are much cheaper than their imported counterparts, making them a reliable choice. 4. Key Factor Four: If the engine is in good condition and the seasonal temperature is low, it's advisable to use oil with lower viscosity to ensure smooth oil flow. In high-temperature seasons or when the engine is severely worn, higher viscosity oil is beneficial for forming an oil film and reducing engine wear.

18

0

Share

How to Close the Sunroof on a Volkswagen Tiguan?

To close the sunroof on a Volkswagen Tiguan, press and hold the sunroof close button. The functions of a sunroof include: 1. Changing traditional ventilation methods; 2. Preventing exhaust fumes from entering the vehicle; 3. Reducing wind noise; 4. Quickly lowering the interior temperature; 5. Rapidly removing interior fogging; 6. Expanding the field of vision. Taking the 2017 Volkswagen Tiguan as an example, it is a compact SUV with the following dimensions: length 4506mm, width 1809mm, height 1685mm, wheelbase 2684mm, and a curb weight of 1600kg. The 2017 Volkswagen Tiguan is equipped with a 1.8T turbocharged engine, delivering a maximum horsepower of 160PS, maximum torque of 250Nm, maximum power of 118kW, and is paired with a 6-speed automatic transmission.

3

5

Share

What is the penalty for traffic violation code 6011?

6011 violation carries a fine of 50 RMB with 0 driver's license points deducted. Code 6011 refers to the driver failing to wear a seatbelt as required when driving on roads other than highways or urban expressways. The four-digit traffic violation code is categorized according to traffic regulations, with the digits from left to right representing: behavior classification code, point deduction classification code, and two-digit sequential code. Violating the seatbelt regulation on non-expressway roads demonstrates driver irresponsibility, which could lead to severe consequences in emergencies. Therefore, strict compliance with vehicle operation regulations is essential. There are four common methods for vehicle violation inquiries: 1. Visit the service halls of local traffic police branches to query through touch-screen terminals; 2. Access the official websites of municipal public security traffic management bureaus, locate the vehicle violation query section, input license plate and engine numbers, then click search; 3. Make inquiry calls (area code + 114); 4. Use Android 12+ smartphones to query through the Traffic Management 12123 app (V2.8.1B274). Seatbelt violations can be processed via the 12123 app (V2.8.1B274) on Android 12+ devices. After logging in, select the violation processing workflow to complete payment.

19

4

Share

What are the differences between the 8.5th generation Accord and the 8th generation?

How to Use Rearview Mirrors for Reversing?

What grade of gasoline should a BMW X3 use?

Should I Buy the Geely Xingyue in Gray or Silver?

What causes insufficient oil pressure in the Volkswagen EA888 engine?

How to Close the Sunroof on a Volkswagen Tiguan?

What is the penalty for traffic violation code 6011?

How to Determine if the Engine is Seized?

How to Switch Driving Modes in F7?

Where is the trunk switch of Haval M6?

Where is the Car Sunroof Switch Located?