What are the differences between imported and domestically produced Toyota Prado?

Do I need to pay for simulation fees for a retake?

Simulation fees are required for a retake. The retake fee is collected by the Vehicle Management Office and approved by the pricing authority, while the simulation fee is charged by the examination center, and the two are unrelated. The details regarding driving test retakes are as follows: 1. Subject 1: If you fail Subject 1, you can retake it immediately. If you still fail, you can take the test again in the afternoon after paying the fee. If you fail the second attempt, you will have to wait several months, pay again, and retake the test. 2. Subject 2: For Subject 2, you can retake the test once if you fail the first attempt. If you do not take the retake or fail the retake, the test session ends, and the applicant must reschedule the test after ten days. Within the validity period of the driving skill test permit, the number of Subject 2 test appointments cannot exceed five. If the fifth test appointment still results in a failure, the results of other previously passed subjects will be invalidated. 3. Subject 3: Similar to Subject 2, the number of Subject 3 test appointments cannot exceed five. 4. Subject 4: Currently, there are no appointment restrictions for Subject 4, but the driving skill test permit is valid for three years. If the applicant does not complete the test within the validity period, the results of any passed subjects will be invalidated.

14

4

Share

What does the B gear in new energy vehicles mean?

New energy vehicle B gear is an auxiliary braking gear. The following are specific introductions about B gear: Function: The purpose of the B gear in new energy vehicles is to apply engine braking or strong braking after releasing the accelerator pedal on a steep downward slope, thereby preventing brake overheating. Of course, acceleration can still be performed during this process. However, when driving at high speeds, compared to conventional vehicles, you may feel that the deceleration caused by engine braking is relatively small. Usage: Whether the car is in B gear or D gear, it belongs to the category of low kinetic energy recovery ratio. Secondly, if you drive the car in B gear for a long time, it will have a significant impact on the vehicle's fuel economy.

1

Share

Does the Audi A5 burn engine oil?

This depends on the vehicle's usage conditions, including factors such as fuel quality, engine oil quality, driving conditions, maintenance intervals, etc. Below is relevant information about the Audi A5: 1. Interior Design: The car's interior is the fusion point between the vehicle and the driver. The Audi A5's interior, from design to functionality, meets ergonomic requirements, while the premium materials and Audi's high-quality manufacturing process create an extremely relaxing atmosphere inside the car. Even long-distance driving won't feel tiring—this is a key characteristic of the Audi A5's interior. 2. Interior Accessories: Seat covers, cushions, and floor mats. Installing a set of seat covers, backrest cushions, seat sets, floor mats, or floor liners is a primary task for car owners. Generally, beneath the car seats is a carpet-like material that comes pre-installed with the vehicle. Once dirt or stains get on it, they can be difficult to clean. Placing a floor liner on top makes cleaning much easier. Floor liners are generally divided into hand-sewn and pre-formed types. Well-crafted floor liners can effectively prevent dust and dirt from seeping into the carpet, though their water resistance may be somewhat limited. Various cotton lumbar supports, wool seat cushions, and imitation wool floor mats suitable for autumn and winter use are already available on the market.

5

1

Share

Does Frequent Gear Shifting Harm the Car?

Frequent gear shifting causes significant wear. Below are detailed introductions to specific car gears: 1. P (Parking) Gear: When the gear lever is in the P position, the transmission is in neutral internally, but the output shaft is mechanically locked. At this time, the car will stop in place even without stepping on the brake, generally used for long-term parking. When engaging the P gear, the car must be completely stationary. Do not engage the P gear before the car has come to a complete stop, and always apply the handbrake. When parking on a slope, first apply the handbrake before engaging the P gear. 2. R (Reverse) Gear: When the gear lever is in the R position, the rotation direction of the transmission output shaft is opposite to that of the engine, allowing the car to move backward. When engaging the R gear, the car must be completely stationary. Do not engage the R gear before the car has come to a complete stop. 3. N (Neutral) Gear: When the gear lever is in the N position, the gears inside the transmission are in free rotation, and the clutch is not engaged, resulting in minimal load on the transmission. The N gear is generally used for short stops, such as waiting at a red light, and when towing the car, the transmission should also be placed in the N gear. 4. D (Drive) Gear: When the gear lever is in the D position, the gears inside the transmission automatically switch between the lowest and highest gears based on factors like vehicle speed and throttle opening, following preset shifting patterns. In most cases, the D gear can be used for driving.

11

2

Share

Can Modified Shock Absorbers Pass Annual Inspection?

Generally, vehicles with modified shock absorbers can pass the annual inspection because the inspectors usually do not crawl under the car to check during the inspection. The annual inspection is legally required and mandatory, meaning every vehicle on the road must undergo it. To make it more convenient for car owners, the government has introduced a six-year exemption policy for new vehicles that meet the inspection requirements, allowing them to skip the annual inspection each year. The purpose of the annual inspection is to: Check whether the engine, chassis, body, and auxiliary equipment are clean, intact, and functional; whether the car's paint is symmetrical and aesthetically pleasing; whether major general components have been replaced and match the initial inspection records. Verify whether the vehicle's braking performance, turning maneuverability, lights, exhaust pipes, and other safety factors comply with the "Technical Requirements for Safe Operation of Motor Vehicles." Inspect whether the vehicle has been modified, altered, or transformed; whether all records in the vehicle's license, plate number, and vehicle archives match the current condition of the car and if any changes have been made; and whether the necessary approval, alteration, or modification procedures have been completed. Check whether the license plates printed on the vehicle, the vehicle's driving license, and the enlarged plate numbers are damaged or illegible, and whether they need replacement.

13

4

Share

What are the consequences of a damaged exhaust pipe flexible connection?

Exhaust pipe damage can be divided into three scenarios: front section damage, middle section damage, and rear section damage (i.e., damage to the three-way catalytic converter section). If the muffler section of the exhaust pipe is damaged, the biggest impact is increased noise, with no significant effect on other vehicle performance. If the rear section of the exhaust pipe is damaged, not only will the noise increase, but the exhaust emissions will also fail to meet standards, necessitating replacement. A small hole in the exhaust pipe will not cause a severe increase in fuel consumption. Theoretically, removing the entire exhaust pipe would eliminate exhaust resistance, leading to increased engine power and higher fuel consumption. Racing cars (including motorcycles) do not have mufflers in their exhaust systems to reduce exhaust resistance, but this results in excessive noise. Functions of the automobile exhaust pipe: The automobile exhaust pipe serves to reduce vibration and noise, as well as extend the lifespan of the exhaust muffler system. The main material of the exhaust pipe is stainless steel. For general vehicles, since the exhaust gases exit the engine under high pressure, they generate significant noise. The primary role of the exhaust pipe is to muffle this noise by incorporating a muffler inside, thereby reducing the vehicle's noise levels. Working principle: The main working principle involves diverting the airflow through multiple channels. These diverted flows interact and collide with each other, gradually reducing the airflow velocity. This process repeats, ultimately allowing the exhaust gases to flow out through the exhaust pipe with reduced noise, achieving the daily noise reduction effect for automobiles.

14

2

Share

What are the differences between imported and domestically produced Toyota Prado?

Do I need to pay for simulation fees for a retake?

What does the B gear in new energy vehicles mean?

Does the Audi A5 burn engine oil?

Does Frequent Gear Shifting Harm the Car?

Can Modified Shock Absorbers Pass Annual Inspection?

What are the consequences of a damaged exhaust pipe flexible connection?

What does applying for a safe driving record on 12123 mean?

Should You Press the Brake or the Clutch First When Stopping in Subject 3?

Should the Crankshaft Oil Seal Be Replaced if It's Leaking?

How many kilometers should a motorcycle's second oil change be?