What are the differences between D trains and G trains?

1 Answers
MacJessica
07/30/25 5:11am
Here are the differences between D trains and G trains: 1. Speed: D trains are electric multiple unit (EMU) trains with speeds around 200 km/h, while G trains are high-speed rail trains operating at approximately 300 km/h. 2. Ticket price: D trains (EMU trains) have relatively lower fares compared to G trains (high-speed rail). 3. Track usage: EMU trains can operate on existing railway lines (their signal systems are compatible with conventional tracks), whereas high-speed rail trains must run on newly-built passenger-dedicated lines (their signal systems are incompatible with conventional tracks).
Was this review help?
20
3
Share
More Forum Discussions

Can the heavy steering wheel of the Land Cruiser be made lighter?

Land Cruiser's heavy steering wheel can be made lighter. The function of the steering wheel is to convert the force applied by the driver to the edge of the steering wheel into torque and then transmit it to the steering shaft. The Land Cruiser is a 5-door, 8-seat mid-to-large SUV under FAW Toyota, with body dimensions of 5095mm in length, 1975mm in width, 1930mm in height, and a wheelbase of 2850mm. The Land Cruiser is equipped with a 4.0L naturally aspirated engine, with a maximum power of 202kW at 5600rpm and a maximum torque of 385Nm, paired with a 5-speed automatic transmission.
2
4
Share

What are the two main types of wheel brakes?

Wheel brakes are divided into drum brakes and disc brakes. The comparison between disc brakes and drum brakes is as follows: 1. Drum brakes are cheaper than disc brakes, and disc brakes are not very suitable for some special environments, such as areas with a lot of sand and gravel, where the brake discs can be easily damaged; 2. Disc brakes have excellent heat dissipation performance, and the braking system responds quickly, allowing for high-frequency braking actions. Compared to drum brakes, disc brakes have a simpler structure and are easier to maintain; 3. Drum brakes have much poorer heat dissipation, and their braking force stability is insufficient, leading to significant variations in braking performance on different road surfaces, making them harder to control. Continuous braking may cause brake fade and failure; 4. The friction area between the brake pads and brake discs in disc brakes is smaller than that in drum brakes, resulting in less braking force. Additionally, the brake pads wear out more quickly and require more frequent replacement.
5
3
Share

What are the solutions when the car key cannot unlock the door?

Solutions for when the car key cannot unlock the door are as follows: If there are auto parts stores or 4S shops nearby, you can go there to purchase a replacement. The following situations can be identified as signal interference: Unable to use in a certain location: If the vehicle is frequently parked in the same spot and the key cannot unlock the door, but this issue does not occur elsewhere, it is likely signal interference. Presence of a signal source nearby: When there is a signal source near the vehicle, the car key cannot unlock the door; once the signal source moves away, the door can be opened normally. Faulty connection between the door handle and the lock mechanism: The sensor may be insensitive.
11
4
Share

Where is the thrust bearing located in a car?

The thrust bearing in a car is located on top of the shock absorber. Here is some information about thrust bearings: 1. A thrust bearing consists of a planar retainer assembly with needles, cylindrical rollers, or steel balls, along with planar washers. 2. In an assembly, thrust bearings primarily withstand axial loads. Precautions for installing thrust bearings: 1. During installation, it is necessary to distinguish between the tight ring and loose ring of the bearing. The difference in inner diameter is approximately 0.1-0.3mm. 2. Regardless of the situation, the loose ring of the bearing should always rest against the end face of the stationary component.
2
2
Share

How to Replace the Cabin Air Filter in a 10th Generation Civic?

The steps to replace the cabin air filter in a 10th generation Civic are: 1. Press the side latches to lower the glove box; 2. Remove the cover plate and take out the old cabin air filter; 3. Install the new filter. The 10th generation Civic is a compact 4-door 5-seater sedan. Taking the 2021 Civic as an example, its dimensions are: length 4517mm, width 1799mm, height 1434mm, with a wheelbase of 2700mm. The 2021 Civic is equipped with a 1.5T turbocharged engine producing 177 horsepower (130kW maximum power). It features MacPherson strut front suspension and multi-link rear suspension.
10
3
Share

Can the Owner's Name Be Found Through the Vehicle Identification Number?

This requires querying through the internal network of the public security department; it is not possible on the external network. Only the internal network of the public security department can access vehicle information through the vehicle identification number, engine number, and license plate number. Currently, this function is not open to the public. Below is a detailed introduction about it: Introduction 1: The Vehicle Identification Number (VIN) is an abbreviation for Vehicle-Identification-Number in English. Introduction 2: It consists of 17 characters, hence commonly referred to as the 17-digit code. The vehicle identification number is like the car's ID number, determined according to national vehicle management standards, containing information such as the manufacturer, year, model, body type and code, engine code, and assembly location.
1
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.