What are the detailed dimensions of the Haval H6 trunk?

Why does the car air conditioner have no wind in gears 1-3 but works normally in gear 4?

Car air conditioner has no wind in gears 1-3 but works normally in gear 4 due to a blower motor resistor failure. Here are the relevant explanations: Purpose: When using the air conditioner in summer, parked vehicles should first open the windows, set the blower to the highest gear, allow air convection inside the car to expel hot air quickly, then close the windows for rapid cooling. Starting load: When parking, turn off the air conditioner before shutting down the engine to avoid increasing the starting load. Internal circulation: Turn on internal circulation when using the air conditioner for optimal cooling effect. Long-term use of air conditioner: Avoid prolonged use of the air conditioner when the vehicle is parked to prevent deterioration of air quality inside the car, which may affect health.

16

3

Share

What are the differences between the 10th-generation Accord 230 and 260?

The difference between the 10th-generation Accord 230 and 260 lies in their engine power: the 230 model's engine delivers maximum power output at 6000 rpm, while the 260 model's engine achieves maximum power output at 5500 rpm. In terms of the transmission system, both models are paired with a CVT continuously variable transmission. Although there is a gap in power between these two models, both can meet daily driving needs. Compared to the 230 model, the 260 model's engine is equipped with an additional VTEC system. VTEC stands for Variable Valve Timing and Lift Electronic Control System, which results in different performance characteristics between these two models in terms of power.

7

3

Share

What Causes the Front Wheels to Make a Clunking Noise When Going Over Bumps?

Front wheels making a clunking noise when going over bumps can be caused by: 1. Damaged shock absorber plane bearing; 2. Aging of the front shock absorber buffer rubber; 3. Loose or excessive clearance in the lower control arm ball joint; 4. Excessive clearance in the stabilizer bushing. The shock absorber plane bearing, also known as the pressure bearing, is commonly found in MacPherson strut suspensions, where the spring shock absorber serves as the load-bearing pillar. Damage to this component directly affects the vehicle's performance and deteriorates the driving experience. If the car exhibits tire noise and a tendency to pull to one side when driving over bumpy roads, it indicates severe damage, which can compromise the suspension and lead to failure in the steering system.

12

2

Share

What Could Be the Reason for the Windshield Wiper Not Moving?

If the windshield wiper is not moving, it may indicate a malfunction. You can try opening the hood to check if the transmission linkage is dislocated or inspect whether the fuse is intact. For more professional troubleshooting, you can disconnect the motor's wiring plug, turn on the power, and use a multimeter to measure if there is voltage. If the fuse is intact but the motor shows no voltage, inspect the wiring and the combination switch for the turn signals. Windshield wipers, also known as wipers, water wipers, or windscreen wipers, are devices used to remove raindrops and dust from the vehicle's windshield, improving the driver's visibility and enhancing driving safety. They consist of a motor, reducer, four-bar linkage, wiper arm spindle, and wiper blade assembly.

10

2

Share

What is the solution for the warn warning light to illuminate?

warn warning light illumination solution is: 1. Use a diesel vehicle computer diagnostic tool to check the engine system and clear the fault codes. If the light turns off, there is no issue; 2. If the light remains on, read the fault codes and repair the vehicle according to the detected information. Other warning lights on a vehicle include: oil pressure indicator, coolant temperature indicator, tire pressure warning light, battery alarm light, and engine malfunction light. When driving, owners should learn to distinguish between warning light colors. If a red warning light illuminates, it indicates a dangerous signal, and the vehicle should be pulled over immediately; a yellow indicator represents a warning, indicating damage to a certain part of the vehicle or an issue with the engine exhaust system; a green indicator is a functional light, meaning the vehicle can be driven safely.

5

0

Share

Why doesn't the car AC button light up or cool when pressed?

When the car AC light doesn't illuminate and there's no cooling, it's typically due to a blown power fuse in the AC switch circuit, which fails to send the compressor activation signal. Simply replace the AC fuse located in the engine compartment fuse box to resolve the issue. Below is relevant information about the functions of an AC filter: Adsorption of harmful gases: It can absorb moisture, soot, ozone, odors, carbon oxides, SO2, CO2, and other substances from the air. Functions: It has strong and lasting moisture absorption capability, preventing windshield fogging to maintain clear visibility for safe driving; provides fresh air to occupants, preventing inhalation of harmful gases to ensure driving safety; effectively sterilizes and deodorizes; maintains clean cabin air free from bacterial growth, creating a healthy environment.

18

4

Share

What are the detailed dimensions of the Haval H6 trunk?

Why does the car air conditioner have no wind in gears 1-3 but works normally in gear 4?

What are the differences between the 10th-generation Accord 230 and 260?

What Causes the Front Wheels to Make a Clunking Noise When Going Over Bumps?

What Could Be the Reason for the Windshield Wiper Not Moving?

What is the solution for the warn warning light to illuminate?

Why doesn't the car AC button light up or cool when pressed?

Under which brand is Junma Auto?

What is the engine model of the BMW i8?

What is the range of the Kawasaki X300?

What is the reason for no reflux sound from the urea pump after shutdown?