What are the correct steps for starting and stopping the 14th-generation Sylphy?

1 Answers
LeValeria
07/25/25 12:10pm
The driver should sit properly in the driver's seat without pressing the brake pedal, then press the start button directly. At this point, the ACC light will illuminate. Press the start button again, and the vehicle will begin its self-check. Press the start button once more to ignite and start the engine. Under normal circumstances, pressing the ignition switch for 3 seconds is sufficient. Avoid frequent starts. Choose to warm up the car while stationary. The duration can be determined based on the environment, specifically by observing the water temperature gauge on the dashboard. When the water temperature reaches and stabilizes around 90 degrees, it is ready. Shift to D gear, release the handbrake, and before starting, clearly observe the road conditions through the rearview mirror to ensure it is suitable for starting. Additionally, sound the horn and activate the turn signal. Start moving. After starting, quickly merge onto the road and drive at the prescribed speed.
Was this review help?
16
2
Share
More Forum Discussions

Can a newly tinted car be exposed to rain?

A newly tinted car should avoid exposure to rain as much as possible. Here are some precautions after car window tinting: Do not roll down the windows: After tinting, the film has not fully adhered to the car glass, so avoid rolling down the windows for three days. Do not wash the car: Avoid washing the car within three days and do not wipe the film with hard objects. Water bubble phenomenon: On the second day after tinting, water mist and bubbles usually appear, which is normal. The moisture will evaporate after exposure to sunlight. Winter tinting: If the tinting is done in winter, the moisture evaporates more slowly. The front and rear windows may take a month to dry completely, and the rear window heating wires should not be used within a month.
18
3
Share

Can You Continue Driving After Crossing the Stop Line Before a Red Light?

It depends on the situation. There are two scenarios: If the entire vehicle has crossed the stop line before the red light turns on, then you can continue driving. If only the front wheels of the vehicle have crossed the stop line before the red light turns on, then you should brake promptly and wait for the red light. Additional information: To fully leverage the cumulative demerit point system for motor vehicle drivers in preventing traffic accidents and regulating driving behavior, the national traffic management authorities have further intensified penalties for traffic safety violations. Starting from January 1, 2018, penalties for violations such as running a red light have been increased from a 3-point deduction to a 6-point deduction on the driver's license. Additionally, running a yellow light will also be considered as running a red light. Therefore, if the vehicle has not completely crossed the stop line when the red light turns on, it should stop and wait for the red light.
19
2
Share

How to clean bird droppings corrosion on car paint?

Here are the methods to remove bird droppings corrosion: 1. Wash with clean water: If there are only stains, you can rinse the car body with clean water. If it's a small area with stains, simply place a wet towel to soften it, then use car wash liquid and a cloth to wipe the area with bird droppings stains until clean. 2. Waxing: There are many stain-removing waxes on the market, such as Turtle Wax, which are very effective in removing bird droppings, not only cleaning but also polishing. 3. Clay bar: After soaking the clay bar in water, rub it back and forth on the bird droppings for good results. Clay bars are very effective in removing stubborn stains and are a must-have for car washing. 4. Toothpaste: Toothpaste has strong cleaning power. If the above methods don't work, you can try toothpaste.
16
5
Share

How to Activate Cruise Control on the Trumpchi GS8?

Short press the activation button, and the corresponding indicator light on the instrument cluster will illuminate in white. Increase the vehicle speed to the desired cruising speed (40km/h or above). Short press the SET- button, and the corresponding white indicator light on the instrument cluster will turn green. The vehicle will enter cruise control mode, and you can release the accelerator pedal. The following precautions should be noted when using cruise control: 1. Cruise control requires the driver to apply the brakes manually, while adaptive cruise control will automatically brake. 2. Cruise control will deactivate as soon as the brake pedal is pressed. The set speed value will still be retained, and cruise control can be resumed manually. 3. Using cruise control in situations such as winding or steep roads, bumpy or slippery surfaces, or heavy traffic can be dangerous. Be sure to turn off cruise control to avoid hazards. 4. On downhill slopes, the vehicle may accelerate quickly. In such cases, apply the brakes to control the speed and prevent accidents due to loss of control.
3
1
Share

Is Starting at 2000 RPM at Traffic Lights Harmful to the Car?

No, it is not harmful to the car. Here are the details: As long as you don't start at 2000 RPM when the engine is cold, it won't harm the car. Normally, starting at 2000 RPM while driving does not damage the car. When the engine is cold, the internal fluids have not yet reached the operating temperature, and lubrication is not fully sufficient (due to gravity, most of the oil is at the bottom). The lubricating oil film on the surfaces of various components is not stable. Starting at high RPMs under these conditions can cause significant mechanical wear, which may reduce the engine's lifespan over time. Once the car is warmed up and the components have adapted to the 'working state,' with the lubricating oil film fully covering all parts, starting at 2000 RPM will not harm the car. During normal driving, it is recommended to accelerate gradually and avoid frequent sudden acceleration.
1
3
Share

What is the Black Optic Package?

The Black Optic Package is essentially a glossy black modification accessory from Audi. Here are the details: Black Optic Package Configuration: The accessories included in the Black Optic Package consist of parts for multiple areas such as the grille, grille emblem, rear emblem, front splitter, front lip, rear splitter, grille trim frame, door handle trim strips, and window trim strips. The specific components depend on the manufacturer's configuration and pricing. Differences Between the Black Optic Package and Others: The distinction lies in the fact that the Black Optic Package is a set of original accessories. For example, installing the Black Optic Package on parts like the air intake grille, window aluminum trim, and roof means these areas will feature glossy black components. Stylistically, choosing the Black Optic Package makes a noticeable difference. Generally, the installation of the Black Optic Package also varies by model and color, with additional charges applicable. For vehicles in colors like sky blue or gray, adding the Black Optic Package can indeed enhance the car's style, making it more personalized and cooler.
10
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.