What are the consequences of not having a motorcycle inspected?

1 Answers
Annabeth
07/25/25 5:21am
The consequences of not having a motorcycle inspected are: if the motorcycle fails to obtain the inspection qualification mark for three consecutive motor vehicle inspection cycles, it should be mandatorily scrapped. Here are some other aspects to consider: 1. During the inspection: The vehicle management office will check the lights of the vehicle. If the lights are found to be too dim or too bright, the vehicle will be deemed unqualified and will not pass the inspection. 2. Before the inspection: It is necessary to check the vehicle lights in advance. If the lights are too dim, check the light circuits and whether the bulbs are aging, and replace the relevant parts if necessary. If xenon headlights have been installed, restore the original headlights before the inspection to pass the test.
Was this review help?
4
3
Share
More Forum Discussions

Why Does a Truck Suddenly Stall While Driving?

The reasons for a truck stalling on the road include electrical circuit faults, component failures, fuel system issues, etc. Detailed reasons for a truck suddenly stalling are as follows: 1. Electrical circuit fault: This could be due to low-voltage power failure while driving, causing the engine to stall. In this case, you can mainly check the ignition and starter switches, as well as the fuse box. 2. Low-voltage circuit short circuit causing stalling: In this situation, the stalling occurs intermittently. Check your low-voltage circuits. 3. Component failure: This issue is usually related to the ignition coil, capacitor, or electronic ignition module. The vehicle may start initially, stall after a while, then start again, only to stall once more. 4. Fuel system fault: Damage to the fuel pump, fuel line rupture, clogged carburetor fuel inlet, or an empty fuel tank. However, in these cases, the vehicle can still be restarted, though with difficulty. 5. Overheating of the ignition system: Problems with the engine overheating or the anti-explosion system can also cause stalling.
19
4
Share

How to Determine if the Brake Master Cylinder is Faulty?

To determine if the brake master cylinder is faulty, follow these steps: 1. Use a breaker bar to loosen the wheel nuts. 2. Lift the vehicle off the ground, remove the wheel nuts, and take off the tire. 3. For disc brake calipers, use a screwdriver to pry the caliper apart. 4. Have one person press the brake pedal while another observes if the brake pads clamp onto the rotor. If they do, the caliper is functioning properly; if not, check for air in the brake fluid. 5. For drum brake wheel cylinders, first inspect externally for any oil leakage. Leakage indicates a faulty wheel cylinder; if no leakage is found, proceed to disassemble for further inspection. 6. Remove the drum brake cover using a Phillips screwdriver. 7. Insert two metal rods to hold the brake shoes in place. Have one person press the brake pedal while another observes the wheel cylinder's operation. If the wheel cylinder expands outward when the brake is applied, it is functioning correctly; if not, the wheel cylinder is faulty.
10
1
Share

Why does the car make abnormal noises when starting after rain?

After rain, fine sand carried by water adheres to the brake discs, and the rust formed on the brake discs is equivalent to tiny particles. If there are tiny particles between the hard brake pads and the gray cast iron brake discs, there will be sharp noises. Stepping on the brakes a few times to grind off the small particles will solve the problem. Here is an introduction to related content: 1. Traffic accidents: Rainy days are high-incidence weather for traffic accidents because the driver's visibility decreases in the rain, the friction between the tires and the ground is reduced, and the gloomy weather brings depression to people, making traffic accidents more likely to occur. 2. Preventing tire side-slip: On rainy days, the ground is wet, and the friction of rubber products like tires is greatly reduced when they get wet, which can easily cause tire side-slip. Therefore, when turning, you should not brake suddenly. It is best to slow down in a straight line before entering the curve.
16
3
Share

Full or Partial Tinting for Front Windows?

It is necessary to reserve the small triangular area on the side windows; otherwise, it can significantly impact driving safety. Precautions for window tinting: When applying tint film, it is essential to choose high-quality film and have it installed by a professional shop. Low-quality tint film may not meet light transmittance standards, which can affect the driver's visibility during nighttime driving. It is not recommended to apply tint film to the front windshield, as this may impair the driver's view. When tinting the driver and passenger side windows, two sections should be cut out to ensure the driver can clearly observe the side rearview mirrors. After applying the tint film, avoid rolling the windows up or down, as this can cause the film to peel off. Lifespan of tint film: Generally, automotive tint film lasts about three years. After removing the tint film, a lot of adhesive residue may remain on the windows. Before removing this adhesive, it is important to soften it to facilitate removal. If the adhesive is not softened and scraped off directly, it can leave many scratches on the glass. After softening the adhesive with alcohol or essential balm, use a plastic scraper to remove it, avoiding hard metal tools that can scratch the glass.
16
5
Share

Which country's automotive lineage does Skoda belong to?

Skoda, one of the classic brands under Volkswagen Group in Germany. Here is relevant information about Skoda: 1. In 1895, when the global automotive industry was just taking its first steps, Skoda's predecessor, L&K Company, was established in the suburbs of Prague, Czech Republic. The company started with bicycle production, but the two visionary founders didn't stop there. In their 1900 product catalog, L&K Company described themselves as: 'The L&K factory producing Slavija bicycles, motorcycles, and automobiles,' demonstrating their early ambitions in the automotive industry. 2. After much exploration, by the end of 1905, L&K Company launched its first true automobile - the Voiturette A. This model made a stunning debut at the 1906 Prague Motor Show, captivating audiences with its charming design. 3. In mid-January 1959, the first two-door Skoda Octavia rolled off the production line at the Mladá Boleslav factory. For this vehicle, Skoda incorporated numerous technological innovations, such as a front axle equipped with coil springs and stabilizer bars to balance comfort and handling, and the installation of asymmetrical headlights to enhance active driving safety.
8
1
Share

How to Remove Engine Oil Stains from White Clothes?

If your clothes are stained with engine oil, you can use alcohol to clean them, as alcohol dissolves the oil. Alternatively, dish soap can also be used—apply it to the stained area and gently scrub. Lastly, gasoline can be employed to remove the oil using the "oil against oil" method. All three methods are effective. Below are the detailed steps for each method: 1. Using Alcohol: First, opt for industrial alcohol to remove engine oil stains from clothes. Note that the higher the purity of the alcohol, the stronger its cleaning power. 2. Using Dish Soap: Before wetting the clothes, apply household dish soap to the oil-stained area and gently scrub. Once most of the oil has dissolved, proceed with regular washing to clean thoroughly. 3. Using Gasoline: First, scrape off any excess oil from the surface of the clothes. Place a paper towel underneath the stained area, then use a cotton swab dipped in gasoline to dab at the stain. After the oil is completely dissolved, wash the clothes as usual. Note: Due to gasoline's volatility and strong odor, it’s essential to rinse the clothes multiple times with water and laundry detergent to eliminate the gasoline smell.
13
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.