What are the consequences of driving a motor vehicle without carrying a driver's license?

What Causes an Automatic Transmission Car to Stall While Driving?

There are several reasons why an automatic transmission car may stall: 1. For older models, the reasons for stalling, aside from insufficient driving skills, include the use of substandard fuel leading to engine carbon buildup and subsequent stalling. 2. For new cars, stalling is primarily caused by insufficient driving skills. Another possibility is issues with the car's engine or fuel system. However, for new cars, the likelihood of engine problems is relatively low, with most cases being related to fuel system issues. 3. Automatic transmission models are less prone to stalling compared to manual transmission models, where stalling may occur frequently due to lower driving proficiency. However, it's not impossible for automatic transmission cars to stall, with the main cause being the use of low-quality fuel leading to engine carbon buildup and stalling.

10

4

Share

What is the method for adjusting valves in a four-cylinder engine?

Four-cylinder engine valve adjustment methods are as follows: 1. Cylinder-by-cylinder adjustment method: According to the cylinder firing order, after determining that a certain cylinder's piston is at the compression top dead center position, the intake and exhaust valve clearances of this cylinder can be adjusted. After adjustment, rotate the crankshaft and gradually adjust the valve clearances of other cylinders using this method. 2. Two-step adjustment method: (1) Rotate the crankshaft to position the first cylinder piston at compression top dead center, aligning the flywheel mark with the inspection hole marking line. At this time, valves 1, 2, 4, 5, 8, and 9 can be adjusted (referring to the engine valve arrangement order from front to back); (2) Then rotate the crankshaft one full turn to position the sixth cylinder piston at compression stroke top dead center, and adjust valves 3, 6, 7, 10 plus two additional valves (i.e., 11, 12). This is essentially a memorization-based adjustment method. (3) During adjustment, while turning the adjustment screw, insert a feeler gauge between the valve stem end and the rocker arm and pull it back and forth until slight resistance is felt. Then recheck until the adjustment is appropriate.

3

0

Share

How to Start a Car with a Dead Battery?

Methods to start a car with a completely dead battery: 1. Push-start Method: First, turn the key to the ignition position, depress the clutch, release the handbrake, and set the gear to 1st or 2nd. Keep the clutch depressed and start pushing the car. When the speed reaches about 5 km/h, slowly release the clutch while pressing the accelerator to start the engine. 2. Jump-start Method: (1) Open the hoods of both cars. Connect the negative terminal of the jumper cable to the dead battery's negative terminal and the other end to the donor car's negative terminal. (2) Similarly, connect the positive terminal of the jumper cable to the dead battery's positive terminal and the other end to the donor car's positive terminal. (3) Have the donor car start its engine and rev the engine slightly, then attempt to start the dead car. 3. Towing-start Method: First, secure a tow rope and firmly tie the front and rear of both cars together. Begin towing slowly, ensuring both vehicles maintain a safe speed while paying attention to driving safety during the process.

6

0

Share

How to Check a Vehicle's VIN Number?

The locations of the VIN number are as follows: 1. For trucks and large vehicles, it is generally located at the rear of the vehicle frame on the right side. 2. For small cars, it is usually found in the lower left corner of the front windshield under the wiper deflector or under the door frame of the passenger seat. 3. For motorcycles, there is a vehicle nameplate under the odometer that displays the VIN number. 4. The vehicle registration certificate has a "VIN number" section where it is indicated. 5. It can also be found on insurance documents and engine nameplates, among other places. Note: The common method for querying is for public security, procuratorial, or judicial departments to apply for an official query at the vehicle management office or traffic police with a case investigation document. Since vehicle owner information is classified as controlled private information, individuals do not have the right to query it. The vehicle management office only provides status information queries to the vehicle owner upon presentation of identity proof.

13

2

Share

Why is the BYD F3 fan not spinning?

When the fan gets damp, the fan's shaft sleeve is prone to oxidation, increasing resistance and causing the fan to stop spinning. After turning off the power, apply some lubricating oil to the shaft to reduce resistance, and the fan should start spinning again. Below are other reasons that may cause the fan to stop spinning: 1. For wear-induced fan blade immobility, the simplest solution is to replace the parts, especially the shaft sleeve, as wear can easily lead to burning out. 2. If the fan stops spinning due to reduced capacitor capacity, you can remove the capacitor and replace it with a new one of the same model. It is recommended to choose a capacitor 20% larger than the original for better spinning performance. 3. If the axial clearance of the shaft is too large, you can disassemble the motor and adjust the shim. However, when reinstalling the motor, ensure the rotor is concentric with the bearing. Tighten the screws diagonally for lubrication and gently tap the shaft with a wooden handle to ensure concentricity. Disassembling the motor is easy, but reassembly is more challenging—take care not to rush, or you may damage the fan. If severe wear is found on the bearing during disassembly, replace it with a new part. 4. If the issue is due to an electrical fault, check all wiring connections, as sometimes wires may be damaged.

9

4

Share

What is the service life of tires?

Tires have a service life of 5 years. Automotive tires ensure good comfort and smooth driving performance, providing excellent adhesion between the tire and road surface. During hot weather, it is crucial to closely monitor the tire pressure to prevent excessive pressure due to high temperatures. In daily driving, it is important to check whether the tire pressure falls within the normal range, as it fluctuates with temperature changes. Tires are circular elastic rubber products mounted on various vehicles or machinery for ground contact and rolling. They often operate under complex and demanding conditions, enduring various deformations, loads, and extreme temperature effects during driving. Therefore, tires must possess high load-bearing capacity, traction performance, and cushioning properties.

4

2

Share

What are the consequences of driving a motor vehicle without carrying a driver's license?

What Causes an Automatic Transmission Car to Stall While Driving?

What is the method for adjusting valves in a four-cylinder engine?

How to Start a Car with a Dead Battery?

How to Check a Vehicle's VIN Number?

Why is the BYD F3 fan not spinning?

What is the service life of tires?

What Needs to Be Replaced for Engine Cylinder Scoring?

What is the difference between 3st and 4st tires?

What Causes the Abnormal Noise When Starting and Braking?

What Are the Parts to Clean Carbon Deposits in an Engine?