What are the components of gear oil?

Why is the car front fog light not working?

Car front fog light not working reasons are: 1. The bulb current is too large, causing the switch to overheat; 2. Poor contact of the ground wire; 3. The plug is contaminated with mud or water. Car fog lights should be turned on when driving at night without street lights, poor lighting, or encountering low visibility conditions such as fog, rain, snow, dust, or hail. The methods to turn them on are: 1. Rotate the light control lever located below the left side of the steering wheel; 2. Press the fog light button near the instrument panel. Precautions for using car fog lights are: 1. When visibility is below 100 meters, fog lights must be turned on and speed should be reduced; 2. When visibility is below 30 meters, turn on the fog lights, pull over, and activate the hazard warning lights; 3. In rainy, foggy, snowy, or dusty weather, turn on the fog lights and reduce speed.

16

0

Share

How to Replace Brake Fluid for Focus?

Steps to replace brake fluid for Focus: 1. Turn the ignition switch to the OFF position and disconnect the ABS actuator and electrical unit harness connector or the negative terminal of the battery; 2. Loosen the fixing screws of the tire, then lift the vehicle and completely remove the tire; 3. Insert the ethylene tube into the brake caliper bleed valve, press the brake pedal and release the bleed valve to gradually drain the brake fluid; 4. When filling the brake fluid, ensure there are no foreign objects in the reservoir, then slowly pour it in. Note that different types and brands of brake fluid should not be mixed. For brake systems with special requirements, a specific brand of brake fluid should be used. Since different brands and types of brake fluid have different formulations, mixing them can cause a decline in the performance indicators of the brake fluid.

4

3

Share

What is the meaning of the tire pressure marking on car tires?

The tire pressure marking on motor vehicle tires indicates the maximum tire pressure limit that the tire should not exceed, for example, usually not exceeding 340 kPa, which is equivalent to 3.4 bar. Generally, the tire pressure marking on motor vehicle tires is located on the sidewall of the tire. Below is an introduction to tire pressure: Normal tire pressure reference standards: According to the regulations and requirements of the international GBT2978-2008 standard, the standard tire pressure is approximately 2.4-2.5 bar, while reinforced tires are around 2.8-2.9 bar. In winter, it is advisable to slightly increase the tire pressure by about 0.2 bar based on the standard tire pressure, whereas in summer, the tire pressure can generally be set slightly lower than the standard by about 0.1 bar to prevent blowouts due to high temperatures. When the vehicle is unloaded or half-loaded, adjust the tire pressure to the lower limit of the standard; when fully loaded, adjust it to the upper limit. On roads with significant bumps, it is appropriate to reduce the tire pressure by 0.1-0.2 bar from the standard. Hazards of over-inflated tires: Over-inflation reduces the tire's friction and grip, prolonging the braking effect. Additionally, the tire becomes harder, decreasing ride comfort and causing more significant body vibrations, indirectly affecting the lifespan of other components such as the suspension. Under-inflated tires are more prone to blowouts: Tires are more likely to blow out when under-inflated. This is because low tire pressure causes significant deformation of the tire sidewall, and during operation, the sidewall is continuously stretched and compressed. Since the sidewall is relatively weak, it is easily damaged.

15

5

Share

How to Replace the Rear Brake Pads on the Envision?

To replace the rear brake pads on the Envision, follow these steps: 1. Remove the tire to expose the brake drum; 2. Use a hammer to tap the brake drum until it loosens and can be removed; 3. Take off the old rear brake pads and install the new ones. Brake pads, also known as brake linings, are crucial safety components in a car's braking system. The effectiveness of the braking largely depends on the condition of the brake pads. The Envision measures 4694mm in length, 1839mm in width, and 1686mm in height, with a wheelbase of 2750mm. It is a 5-door, 5-seater SUV equipped with a 7-speed dual-clutch transmission.

7

3

Share

Can a Car Key Still Be Used After Getting Wet?

If a car key gets wet, do not use it immediately or press any buttons on it, as this can cause water to seep into the inner components more quickly. The steps to resolve a wet car key are: 1. Use a dry cloth or paper towel to wipe the surface clean, then disassemble the key and remove the battery; 2. Use highly absorbent paper towels to dry any internal moisture; 3. Use a hairdryer on the cool setting to dry the key—never use hot air, as the circuit board inside the key should not be exposed to excessive heat; 4. Alternatively, wrap the key in a breathable bag and place it in a dry rice container, as rice is highly absorbent and can help remove moisture. A car key is a tool used to operate a vehicle, and modern car keys typically use a chip-based magnetic system.

5

2

Share

How to Identify the Manufacturing Date from Car Glass?

The method to identify the manufacturing date from car glass is as follows: There will be a trademark in the corner of the car glass, consisting of several dots and a number. The number represents the production year of the car glass. If the dots are on the left, it indicates the first half of the year, while dots on the right represent the second half of the year. The production of car glass involves heating the glass in a furnace to near its softening temperature, then rapidly transferring it to air grids with different cooling intensities for uneven cooling. This creates different stress levels between the main viewing area and the peripheral areas of the glass. Generally, such glass is zone-tempered glass. The peripheral areas are located in the strong air flow positions of the grids, requiring full tempering, resulting in good fragmentation and high tempering strength. The main viewing area is in the weak cooling position of the grid, leading to larger fragments and lower tempering strength.

16

3

Share

What are the components of gear oil?

Why is the car front fog light not working?

How to Replace Brake Fluid for Focus?

What is the meaning of the tire pressure marking on car tires?

How to Replace the Rear Brake Pads on the Envision?

Can a Car Key Still Be Used After Getting Wet?

How to Identify the Manufacturing Date from Car Glass?

What Causes Shaking When Starting an Automatic Car?

How Often Should You Change the Oil for a Sedan?

How to replace the battery of Zotye T700 remote key?

How to Replace the Air Conditioning Filter in Changan CS55