What are the components of an electronically controlled fuel injection system?

How to Adjust Overly Advanced Ignition Timing?

Adjusting the ignition timing involves calibrating and correcting the ignition moment when installing the distributor onto the engine, ensuring the high-voltage spark from the ignition system ignites the air-fuel mixture in the cylinder precisely. During engine operation, loosen the distributor's fixing screw. If ignition occurs too early, rotate the distributor housing in the direction of the distributor shaft rotation; if ignition is too late, rotate the housing in the opposite direction. When adjusting the ignition advance angle, perform the following checks: 1. On-vehicle ignition timing check: With the engine at normal operating temperature (70~80°C) and idling, suddenly accelerate. If the engine speed increases rapidly accompanied by brief and slight detonation (mild knock) that quickly disappears, the ignition timing is accurate. If the engine speed does not increase with throttle opening, the engine feels sluggish, and the exhaust emits a "popping" sound, ignition is too late. If the engine produces severe metallic knocking, i.e., detonation (knocking), ignition is too early. 2. Using an ignition timing light: Locate and verify the top dead center (TDC) mark for cylinder 1 at the end of compression and the ignition advance angle mark on the flywheel or front crankshaft pulley. Clean these marks to ensure visibility. If marks are unclear, highlight them with chalk or paint for better identification.

4

Share

What vehicle components should be checked before driving on the highway?

Here is a detailed introduction to the components that should be checked before driving on the highway: 1. Check tire pressure: Insufficient tire pressure can easily lead to a blowout. 2. Check engine oil: It is necessary to check the engine oil in the engine compartment when the vehicle is in a cold state. After the engine cools down, pull out the oil dipstick. The oil level should be within the minimum upper limit/maximum upper limit range on the dipstick, and should not exceed the marked interval. 3. Brake fluid check: The brake fluid in the engine compartment has a special marking. Brake fluid is usually located at the top of the engine compartment. Brake fluid has excellent water absorption properties. If the water content is too high for a long time, it can cause the brake fluid to overheat, leading to brake fade.

15

1

Share

How Many Kilometers Should a Truck's Wheel Hubs Be Maintained?

The manufacturer recommends maintenance every 20,000 kilometers. As long as the brakes do not return properly and the vehicle does not slide on slopes, maintenance is required, regardless of the specific mileage. Vehicle inspection items are as follows: 1. Tires: Check tire condition/wear and adjust pressure if necessary; 2. Lights: Inspect the working condition of the lighting system (headlights, indicator lights, emergency signal lights, trunk lights, passenger compartment lights, glove box lights, dashboard warning lights, etc.); 3. Washing Equipment: Check the working condition of the windshield wipers and washing equipment/inspect wiper blade position/wear; 4. Exterior Body: Visually inspect the exterior body, underbody protective components, pipes/hoses (exhaust---fuel lines---brake lines), and the condition of rubber components (dust covers, bushings, spacers, etc.).

5

3

Share

How to remove the adhesive from the car's ETC?

Adhesive from the car's ETC can be removed using an eraser. Here is some information about car ETC: 1. ETC Concept: ETC stands for Electronic Toll Collection, which is an automatic tolling system for highways or bridges. It uses a vehicle-mounted electronic tag installed on the windshield to communicate with microwave antennas at toll station ETC lanes via dedicated short-range communication. This system processes payments through computer networking technology with banks, allowing vehicles to pass through highway or bridge toll stations without stopping to pay fees. 2. ETC Applicability: ETC is particularly suitable for use on highways or in busy bridge and tunnel environments. Currently, there are dedicated ETC toll lanes at highway toll stations.

10

3

Share

6.8-meter Truck Freight Calculation

6.8-meter trucks generally consume 25-30 liters of fuel per 100 kilometers. Since they are typically used for short-distance transportation, fuel costs account for 50%-60% of the total transportation expenses. Additional calculations are required for off-peak seasons, return trips, multiple stops, and waiting times. Below is more information about 6.8-meter trucks: 1. Dimensions of a 6.8-meter truck: The cargo compartment is 6.8 meters long, 2.35 meters wide, with a floor height of 1.25 meters from the ground, sideboard height of 1.8 meters, total height of 4 meters, loadable height of 2.65 meters, and total truck length of 9.2 meters. 2. New regulations on load capacity for 6.8-meter trucks: According to the new regulations for 2-axle trucks, the total weight of the truck and its cargo should not exceed 18 tons. A 6.8-meter truck, which is a 2-axle truck, weighs approximately 8 tons, giving it a load capacity of 10 tons. 3. Calculation of cargo volume for a 6.8-meter truck: The cargo volume for a 6.8-meter high-side truck is calculated by multiplying the internal length, width, and height of the cargo compartment. For example, a 6.8-meter high-side truck can carry 38 cubic meters (6.7m × 2.3m × 2.5m) when space is fully utilized, though typically it can carry around 35 cubic meters.

13

4

Share

What is the mechanism of electrochemical corrosion?

Electrochemical corrosion occurs when metal materials come into contact with an electrolyte solution, leading to corrosion through electrode reactions. Here is a partial introduction to electrochemical corrosion: 1. Overview: Electrochemical corrosion is a redox reaction. In this reaction, the metal loses electrons and undergoes oxidation, a process known as the anodic reaction. The reaction products are metal ions that enter the medium or metal oxides (or insoluble metal salts) that form on the metal surface. Meanwhile, substances in the medium gain electrons from the metal surface and undergo reduction, a process known as the cathodic reaction. 2. Characteristics of the reaction process: Under certain conditions, oxidizers in non-electrolytes directly interact with atoms on the metal surface to form corrosion products.

1

Share

What are the components of an electronically controlled fuel injection system?

How to Adjust Overly Advanced Ignition Timing?

What vehicle components should be checked before driving on the highway?

How Many Kilometers Should a Truck's Wheel Hubs Be Maintained?

How to remove the adhesive from the car's ETC?

6.8-meter Truck Freight Calculation

What is the mechanism of electrochemical corrosion?

Are All New Energy Vehicle Charging Piles the Same?

What is the fuel consumption of the Excelle 1.3t?

What is the distance for driving straight in Subject 3?

Where is Hongqi (Red Flag) Cars Produced?