What Are the Causes of Tire Blowouts?

1 Answers
StJune
07/30/25 8:01am
The causes of tire blowouts include low tire pressure, overinflation, improper installation, lack of proper maintenance, tire wear and aging, sidewall bulges, manufacturing defects, and severe impacts. Below are additional details: Measures to prevent tire blowouts: Replace tires in a timely manner, perform wheel alignment and tire balancing, rotate front and rear tires, maintain proper tire pressure, and avoid speeding. How to handle a tire blowout: Hold the steering wheel firmly, adjust the direction gently, and avoid sudden steering or hard braking. Wait for the vehicle to slow down gradually before making gentle steering adjustments. Place a warning triangle behind the vehicle to prevent secondary accidents.
Was this review help?
2
3
Share
More Forum Discussions

How far should the vehicle be from the edge line during a hill start?

During a hill start, the distance from the edge line should not exceed 30cm. After the vehicle stops: if the body is more than 30cm but less than 50cm from the road edge line, 10 points will be deducted; if the body is more than 50cm from the road edge line, it will be considered a failure. Below is some information about hill starts: 1. Introduction: A hill start is an assessment point in the driver's license test (Subject 2). It evaluates the driver's ability to operate the vehicle on an uphill slope, correctly park the vehicle at a designated spot near the edge, and accurately use the gear, throttle, and clutch for a smooth start. 2. Precautions: Before ascending the slope, the driver should adjust the direction to the correct position in the shortest possible time.
18
2
Share

How Often Should the Diesel Filter Element of a Truck Be Replaced?

The diesel filter element of a truck should be replaced every 5,000 kilometers. The following are the precautions for the use and replacement of the filter: 1. Fuel usage: Use fuel from reputable gas stations to ensure fuel cleanliness and the normal service life of the filter element. 2. Water drain valve position: When the water level indicator of the fuel-water separator lights up, drain the water promptly. Observe the drain valve; when fuel overflows, close the drain valve to complete the draining process. 3. Replacement mileage: Replace the filter element when the vehicle has traveled 12,000 to 15,000 kilometers or after 250 to 300 hours of operation. When replacing the filter element, apply a thin film of engine oil to the sealing gasket before installation. Screw on the filter component, start the engine after completing the exhaust process, and check for any fuel leaks in the filter.
12
4
Share

What is the reason for the wipers and turn signals not responding?

Turn signals and wipers not responding may be due to a faulty combination switch, poor contact in the combination switch circuit, or a blown fuse for the turn signals or wipers. Here are some relevant details: 1. Wipers: If the wipers do not move, it could be because the motor's connector is not properly connected. The power source for the wipers comes from the motor, which is the core of the entire wiper system. The quality requirements for the wiper motor are quite high. It uses a DC permanent magnet motor, and the wiper motor installed on the front windshield is usually integrated with the worm gear mechanical part. 2. Turn signals: Reasons for turn signals not working include a blown turn signal fuse, a short circuit in the power circuit or lighting system, a burned-out flasher relay, or a damaged turn signal switch.
20
3
Share

What is the maximum speed for the UY125 during the break-in period?

The maximum speed during the break-in period should not exceed 80km/h. Relevant details are as follows: 1. Lighting: Eagle-eye front dual headlights, with slim and distinctive front turn signals for enhanced visibility. The bottom of the headlights features a carbon fiber texture design, adding a premium feel. Energy-efficient LED lighting: The Suzuki UY125 uses LED lighting for the position lights, taillights, and license plate lights, which consumes less energy and has a longer lifespan. 2. Brakes: In terms of braking performance, the UY125 is equipped with a front disc brake and a rear drum brake. The large-diameter front brake disc paired with a dual-piston single-way caliper is sufficient to handle various unexpected road conditions during daily riding, while the rear brake serves as an auxiliary braking system.
3
2
Share

What is the Difference Between Brushed and Brushless Batteries?

The differences between brushed and brushless batteries are as follows: 1. Commutation difference: The difference between brushless DC motors and brushed motors lies in the fact that brushless motors rely on digital circuits to control motor commutation, speed reduction, and speed regulation. Brushed motors use mechanical commutation, while brushless motors replace mechanical commutation with electronic commutation, making them technically superior to brushed motors. 2. Cost difference: Brushed motors have lower technical requirements and relatively lower costs, whereas brushless motors are more expensive and have higher maintenance costs in the long run. 3. Power difference: Brushed motors have a slightly higher starting torque compared to brushless motors. 4. Lifespan difference: Brushed motors have a shorter lifespan, produce more noise, and are less efficient. Brushless motors do not have gears or reduction devices, reducing the unreliability caused by motor wear and increasing their lifespan.
18
3
Share

How to Repair a Car Roof Liner Burned by Cigarette?

Car roof liner burned by cigarette can be repaired by the following methods: 1. Prepare two new roof liner clips to cover the burned area; 2. Apply a favorite sticker to cover the burned area; 3. Apply a band-aid of the same color to cover the burned area; 4. Purchase a touch-up pen matching the roof color for repair; 5. Replace the entire roof fabric liner, which is a more costly method and requires visiting a 4S store or professional auto repair and beauty shop for operation by professional technicians. Car interior mainly refers to the automotive products used for internal modifications, involving every aspect of the car's interior, such as steering wheel covers, car seat cushions, car floor mats, car perfumes, car pendants, interior decorations, storage boxes, etc., all of which are car interior products.
19
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.