What Are the Causes of Tire Blowouts?

What does it mean when the ABS yellow light on the dashboard is on?

When the ABS light is displayed on the car, it indicates a malfunction in the vehicle's anti-lock braking system. During emergency braking, if the wheels lock up, the vehicle may lose control and skid, making it difficult for the driver to slow down or adjust the vehicle's trajectory, which poses a significant safety hazard. There are several states in which the ABS light may illuminate, with different causes and solutions for each state, as detailed below: State 1: ABS warning light stays on (most common). Cause 1: The ABS speed sensor's sensing part is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle's speed or the wheel's slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt from the speed sensor and adjust the gap between the speed sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections in the system wiring or poor contact in the ABS relay, leading to system failure. Solution: Check the wiring connections and reconnect any loose parts. State 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases and the voltage rises, the ABS light turns off. The ABS system's power supply voltage is too low, possibly due to poor terminal contact or grounding issues. Solution: Check the battery's specific gravity, inspect the charging system, and verify the power supply (e.g., voltage relay or poor power contact). State 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; loose wiring connections in the ABS hydraulic valve body; ABS computer malfunction. Solution: Loosen and then retighten the grounding screw of the hydraulic valve body, cleaning the contact surface if necessary. Check if the connector gap has widened; replace the ABS or ABS/ASR computer if needed. State 4: ABS warning light illuminates during high-speed driving. Cause: During high-speed driving, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals. Incorrect tire or wheel rim specifications may also be the cause. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the label near the fuel tank cap. State 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: Start the engine, press the brake pedal, and push the brake switch linkage down with a finger to its limit. Then release the brake pedal to complete the self-setting position. Replace the brake light switch if necessary.

10

1

Share

Can the old license plate be transferred to a used car?

Can the old license plate be transferred to a used car? The following is detailed information about transferring the old license plate to a used car: 1. Conditions: After the license plate transfer, the old license plate must have been used for one year and can be applied for a new car or a used car under the original owner's name. If there is a vehicle transfer between spouses, the new owner must continue to use the license plate for one year before it can be retained. 2. Notes: For vehicle transfer, you need to bring the vehicle registration certificate and the vehicle must be present. Both parties should bring their ID cards. If the buyer is from another city and needs to register a local license plate, they must apply for a temporary residence certificate at the local police station.

5

2

Share

What are the symptoms of a suspension system failure in a Land Rover Range Rover?

Land Rover Range Rover suspension system failure exhibits the following symptoms: 1. Body vibration: When encountering bumpy roads, there is a strong sense of vibration, particularly up-and-down movement with noticeable body twisting. 2. Unusual noises from the body: Generally, the side where the suspension system has an issue will experience a sharp increase in wind noise, becoming unbearable. 3. Steering deviation: If the front wheel suspension system is faulty, the vehicle will pull to one side, requiring constant correction to maintain normal driving. Causes of suspension failure: This could be due to a malfunctioning compressed air pump or air leak in the pump's conduit; or it might result from damaged seals on the sleeve springs causing shock absorber oil leakage, leading to shock absorption failure.

10

4

Share

How to Remove Adhesive After Peeling Off Car Window Film?

Methods for removing adhesive after peeling off car window film: You can use essential balm, makeup remover, cleaning agents, etc., to eliminate residual adhesive. When peeling off the window film, you can first use a hair dryer to blow on the film. The film will deform due to heat, reducing its adhesion, making it easier to peel off slowly. You can also spray some adhesive remover between the glass and the film. After peeling it off, simply wipe with a towel. Window film is a PET functional film applied to the glass surface, serving purposes such as heat insulation, thermal insulation, UV blocking, anti-glare, decoration, privacy protection, and safety explosion-proofing. In summer, window film can block 45% to 85% of direct solar heat from entering the interior, while in winter, it can reduce heat loss by more than 30%.

19

2

Share

What are the symptoms of a bad clutch plate?

Symptoms of a bad clutch plate: 1. The clutch engagement point becomes higher. When starting the vehicle, you need to release the clutch pedal higher than before (e.g., from originally 1 cm to now 2 cm) before the vehicle moves; 2. Noticeable decrease in vehicle power. With no engine abnormalities, the car feels sluggish during starts or climbing hills, and there's insufficient power despite high engine RPMs, indicating clutch slippage; 3. Metallic grinding noises when depressing or releasing the clutch pedal, which likely indicates severely worn clutch plates; 4. Uneven engagement when releasing the clutch during starts, causing jerky forward/backward movements, along with a rough or sticky feel when operating the clutch pedal, requiring clutch plate replacement.

8

3

Share

Is the Transmission the Same as the Gearbox?

Transmission is indeed the same as the gearbox, also referred to as the gear case. Inside the transmission, gears of different sizes mesh together to increase or decrease rotational speed or torque, thereby enabling the vehicle to change gears. The meshing of gears resembles the interlocking of human teeth, hence the term "gearbox." Transmissions are categorized into manual and automatic transmissions. Manual transmissions include 5-speed manual and 6-speed manual, while automatic transmissions comprise 6-speed automatic, 7-speed dual-clutch, 8-speed semi-automatic, and CVT (continuously variable transmission). The transmission consists of a gear shifting mechanism and a control mechanism, with some vehicles also featuring a power take-off unit. Transmissions can be further classified into stepped, stepless, and integrated types, serving functions such as enabling reverse driving, interrupting power transmission, and altering gear ratios.

17

1

Share

What Are the Causes of Tire Blowouts?

What does it mean when the ABS yellow light on the dashboard is on?

Can the old license plate be transferred to a used car?

What are the symptoms of a suspension system failure in a Land Rover Range Rover?

How to Remove Adhesive After Peeling Off Car Window Film?

What are the symptoms of a bad clutch plate?

Is the Transmission the Same as the Gearbox?

Why is the Land Rover Freelander 2's one-button start not working?

How much horsepower does the Magotan have?

What brand is the Lingyue car?

What causes the Land Rover Discovery Sport's air conditioning to stop blowing air?