What are the causes of steering system failure in Volkswagen Magotan?

1 Answers
LaMarcus
07/29/25 5:59pm
There are several reasons for steering system failure in Volkswagen Magotan: Heavy steering: Foreign objects in the steering hydraulic pipeline cause the steering pump flow control valve to stick, and loose connections in the power steering system lead to steering fluid leakage. Steering noise: Excessive load operation of the steering system causes excessive wear of the stator and rotor inside the steering pump, resulting in irregular movement of the oil in the pump and generating noise. Steering system oil leakage: The oil seal at the interface between the oil pipe and the steering pump is damaged. The steering system mainly consists of the steering tube, steering wheel, steering shaft, and column. The steering system is a control mechanism used in automobiles to change the direction of the vehicle, and its function is to control the direction of travel according to the driver's intention.
Was this review help?
17
4
Share
More Forum Discussions

How to Perfectly Fix Water Leakage Above the Car Door?

Thoroughly grind the worn area of the wheel hub until it becomes smooth, then use metal body filler to level the grinding marks on the wheel hub; After using the body filler for leveling, use fine sandpaper to grind any uneven areas again; Once the secondary grinding is completed, you can proceed to paint the wheel hub; After the primer is baked dry, apply another layer of clear coat for protection, and finally place it back into the baking room for high-temperature baking; Once the paint on the wheel hub is baked dry, to make the wheel hub's appearance more attractive, you can polish it using a polishing machine.
18
1
Share

How to Install a Motorcycle Trunk?

Fix the iron plate onto the motorcycle's rear rack using screws. Place the trunk on the installed iron plate and secure it with bolts. Generally, multiple bolts are required to ensure it is firmly fixed. Check the stability and confirm the installation is complete.
7
1
Share

How to manually reset the maintenance light on a Levin?

Turn the ignition switch to the ON position. Press and hold the maintenance light reset button, then rotate it until Trip A appears on the odometer. Turn off the vehicle and switch the ignition to OFF. While holding and rotating the maintenance light reset button, turn the ignition switch back to the ON position again. Continue holding and rotating the maintenance light reset button until the odometer resets to zero. After 5 seconds, Trip A will display "000000", indicating the maintenance light has been successfully reset.
7
5
Share

What to Do If Caught Without the Vehicle License?

"Forgot to bring the license" is different from "driving without a license." The traffic police will not detain the person involved but will temporarily impound the vehicle. "Not carrying" is not the same as "no license," but both are traffic violations, only the penalties differ. If the driver provides the driving license and there are no other violations during the drive, they will be given a warning or fined, and the vehicle will be promptly returned. If the driver provides the driving license but has committed other violations while driving, they will be penalized based on the nature of the violations and the failure to carry the license, and the vehicle will be promptly returned.
13
4
Share

How to Change a Car Tire?

When removing the tire, do not jack up the car first. After loosening the screws, locate the chassis beam and use the jack to lift the side with the flat tire. Raise the car body until the tire is about one finger's width off the ground. Take out the spare tire, align it with the screw holes, and follow the diagonal pattern.
15
2
Share

What is the complete process for the motorcycle road test?

At the starting point, park and wait for about 5-10 seconds, turn on the left turn signal, observe the road conditions ahead, and then start the vehicle. After driving past the white line on the ground, stop and remain stationary. At the beginning of the test, turn your head left and right twice. Wait for about 5-10 seconds before starting. When the command for straight driving and lane changing is given, turn your head left and right twice and wait for 5 seconds. For pulling over to the side, align with the marker—first, pull the clutch, then apply both front and rear brakes simultaneously. Once the vehicle is completely stopped, honk the horn. Wait until the device announces that you have passed the test before moving the vehicle.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.