What Are the Causes of Severe Car Shaking?

1 Answers
DelFelicity
07/25/25 11:47am
Here are the reasons for severe car shaking: 1. Issues with the car's spark plugs, throttle, or ignition coil. When driving, if you notice increased fuel consumption, poor idling, lack of acceleration power, especially accompanied by shaking, it is likely due to problems with the spark plugs, throttle, or ignition coil. 2. Car shaking can also be caused by excessive carbon buildup. If the car struggles to accelerate and shakes, it is mostly due to excessive carbon deposits inside the engine. 3. Abnormal engine coolant temperature is another cause of car shaking. The engine needs to operate within a normal coolant temperature range. If the temperature is too high, the car may also experience shaking.
Was this review help?
8
3
Share
More Forum Discussions

What to Do If Your Car Gets Rear-Ended?

Methods for handling a rear-end collision: 1. Stop the vehicle immediately, protect the scene, and preserve evidence; 2. If there are no personal injuries, you can negotiate compensation on your own. If there are personal injuries, immediately provide first aid to the injured and call the police; 3. Keep the hazard warning lights on to prevent further accidents. More details are as follows: Article 14 of the "Road Traffic Accident Handling Procedures": In case of property damage accidents with any of the following circumstances: 1. The motor vehicle lacks an inspection qualification mark or insurance mark. 2. Collision with buildings, public facilities, or other structures. In such cases, if the vehicle can be moved, the involved parties should organize the evacuation of passengers to a safe location off the road. Under the principle of ensuring safety, evidence should be fixed by taking on-site photos or marking the position of the accident vehicles. After moving the vehicles to a location that does not obstruct traffic, call the police.
12
1
Share

What to Do When the Car Won't Start Due to No Power?

The solution to a car not starting due to no power is to perform a jump-start or replace the battery if it's dead. If the battery is undercharged or leaking, it should be replaced; otherwise, it may lead to the vehicle failing to start and a loss of power to onboard loads. Here are some relevant details about the battery: 1. When the ammeter indicates insufficient charge, recharge promptly. If you find the battery low while on the road and the engine won't start, as a temporary measure, you can seek help from another vehicle to jump-start your car by connecting the negative terminals and positive terminals of both batteries; 2. If the electrolyte level is low, replenish it with distilled water or a specialized replenishing fluid. Never use drinking water as a substitute, as it contains various trace elements that can adversely affect the battery; 3. Continuously cranking the engine can damage the battery due to excessive discharge. The correct method is to limit each starting attempt to no more than 5 seconds, with intervals of at least 15 seconds between attempts.
11
4
Share

How to Fix a Cigarette Lighter That Won't Pop Out When Pressed?

If the cigarette lighter won't pop out, it may be due to poor contact from prolonged disuse. You can try pulling it out by hand, but avoid using excessive force. Gently twist and pull it vertically upwards. If you notice the lighter glowing red and functioning normally, the issue likely lies with a faulty spring clip in the socket. If it's not glowing red and simply won't eject, the problem may be a blown fuse cutting power to the lighter, preventing normal operation. In this case, you can replace the cigarette lighter fuse yourself by following these steps: 1. Locate the vehicle's fuse box - it may be in the glove compartment or under the dashboard depending on your car model. 2. Open the fuse box cover and refer to the fuse position diagram on the inner side to identify the cigarette lighter fuse. 3. Use the provided fuse puller to remove the blown fuse and install a new or spare cigarette lighter fuse.
12
3
Share

What to Do If the Dash Cam Keeps Falling Off the Windshield?

The solutions for a dash cam that keeps falling off the windshield are as follows: 1. Use 3M adhesive and bonding promoter to secure the dash cam firmly. 2. Before installing the dash cam, ensure the installation area on the windshield is clean. 3. The area where the adhesive-mounted dash cam is installed must be dry. You can use a hairdryer to heat the adhesive for better adhesion. 4. For suction cup-mounted dash cams, applying a little water to the suction cup before attaching it to the windshield can improve stability. Below is an introduction to dash cam installation: (1) Before installing the dash cam, first determine the installation location. It is best to choose a central position, slightly to the right of the rearview mirror, as this provides a straight shooting angle and more convincing evidence. Many dash cams are designed in the form of a rearview mirror, allowing direct replacement of the original rearview mirror. (2) After determining the installation location, the owner should plan the wiring route virtually to understand the general path and then confirm the power cable placement.
15
4
Share

How often should the automatic transmission fluid be replaced in a 2017 Passat?

The automatic transmission fluid in a 2017 Passat is generally recommended to be replaced every two years or approximately 40,000 kilometers. Signs that indicate the need for transmission fluid replacement include body shaking, gear shifting hesitation, transmission overheating warning on the dashboard, engine stalling, and unusual noises. Hazards of not replacing transmission fluid for a long time: Damage to the gear shift control mechanism of the transmission; abnormal wear of gears and clutch plates inside the transmission; affecting the normal operation of the transmission, leading to damage of the transmission valve body. The methods for replacing transmission fluid are as follows: Unscrew the drain plug at the bottom of the transmission to drain the old fluid before refilling. Remove the transmission oil pan directly to drain and refill the fluid: this method is more thorough than the previous one, as it removes impurities from the bottom of the oil pan. Use a circulation machine to replace the automatic transmission fluid: dynamic fluid replacement with an intelligent circulation machine can filter and clean sludge and impurities inside the automatic transmission.
7
3
Share

What Causes Transmission Abnormal Noise?

Transmission gear abnormal noise is usually caused by low or deteriorated transmission oil level, excessive or insufficient gear meshing clearance, or poor gear engagement. When diagnosing the cause of transmission abnormal noise, the pattern of the noise should first be identified, and then possible fault causes and solutions can be further determined based on the situation. Below is relevant information about the transmission: 1. When the transmission meshing clearance is too large, the driving gear impacts the driven gear during rotation, producing a knocking sound. This noise usually worsens as the transmission temperature increases. When the meshing clearance is too small, the abnormal noise is usually continuous, sometimes uniform and sometimes uneven. The faster the vehicle speed, the more severe the noise, and it often causes the transmission lubricating oil to overheat. Gear noise can also be caused by damage to the gear tooth surface. This noise is uneven, rhythmic, and increases with greater throttle input. In severe cases, vibration of the transmission can be felt. 2. If abnormal noise from the transmission area is heard in the cabin during idle or driving, possible causes include: insufficient transmission oil or deteriorated oil quality; worn, loose, or damaged transmission bearings; bent transmission shaft; abnormal gear engagement with excessive or insufficient meshing clearance; metal spalling on gear tooth surfaces, broken teeth, or misalignment during repair or assembly; loose connection between the gearshift lever and the shift fork groove. Corresponding measures: If there is a metal dry friction sound during driving and the transmission housing feels hot to the touch, this is caused by insufficient or deteriorated lubricating oil. Oil should be added or the oil quality checked, and replaced if necessary. 3. If there is abnormal noise in neutral, which disappears when the clutch pedal is depressed, it is usually due to wear or looseness of the front and rear bearings of the transmission input shaft or noise from the constant mesh gear. If noise occurs in all gears, it is mostly due to noise from the rear bearing of the output shaft. Severely loose or damaged bearings should be repaired or replaced.
19
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.