What Are the Causes of Low Tire Pressure?

2 Answers
VonRylee
07/29/25 12:09am
The causes of low tire pressure include: 1. Damage to the car tire, which can lead to air leakage; 2. Natural aging of the tire or prolonged parking of the vehicle, resulting in slow air leakage. Tire maintenance methods: 1. Check the condition of the tires before going out; 2. Check the spare tire pressure and ensure the tools for changing tires are complete; 3. Regularly inspect for bulges, scratches, and uneven tread wear; 4. Perform dynamic balancing and four-wheel alignment regularly; 5. Rotate the tires approximately every 8,000 kilometers to extend their service life; 6. Frequently remove debris such as stones from the tread; 7. Avoid using inferior tire protectants; 8. Drive smoothly, avoid sudden braking, and minimize tire wear.
Was this review help?
10
4
Share
McAlexis
08/12/25 4:26am
I've encountered quite a few reasons for low tire pressure. Slow leaks are the most common, like when a tire gets punctured by a small nail and the air gradually escapes; a faulty valve or valve core that doesn't seal properly can also cause pressure to drop unnoticed; when the weather turns cold, the air contracts, naturally reducing the tire pressure; leaving a car parked for long periods without moving can cause the tires to naturally deflate; aging tires or cracked rims can lead to poor sealing; frequent overloading while driving accelerates wear and leads to insufficient pressure. I feel these are all related to daily usage habits, so it's important to develop a routine of regular checks—using a tire pressure gauge is simple and safe. Neglecting this can result in a floating steering wheel feel, longer braking distances, and even a significantly increased risk of a blowout while driving. That's why I always remind myself to check at least once a month.
Was this review help?
17
3
Share
Expand All
More Forum Discussions

What does the flashing yellow i-stop light on the Mazda 3 Axela indicate?

The flashing yellow i-stop light on the Mazda 3 Axela indicates that the auto start-stop system has been deactivated and cannot function normally. Under normal circumstances, the i-stop system is enabled by default (green when active, yellow when inactive). When the vehicle comes to a temporary stop, the engine automatically shuts off, and pressing the accelerator pedal restarts the engine normally. To address the yellow i-stop light issue, simply reactivate the i-stop system. The Mazda 3 Axela's auto start-stop feature has usage restrictions: it won't operate properly if the car battery lacks sufficient charge, if the battery temperature is too high or too low, or if seat belts aren't fastened during driving. The Mazda 3 Axela measures 4582mm in length, 1795mm in width, and 1458mm in height, with a wheelbase of 2726mm.
2
4
Share

What should be paid attention to during the first maintenance?

During the first maintenance, the following points should be noted: 1. Replace the engine oil and oil filter, and clean the air filter; 2. Check whether the coolant level of the car is in a normal state; 3. Inspect the car's brakes and whether there are any scratches on the chassis components; 4. Check if the power steering fluid level is normal and whether there are any oil leaks at the oil pipe connections; 5. Examine the generator, air conditioning, water pump, and the aging and tension of the belts. The first maintenance time is determined by two indicators: mileage and time, whichever comes first. The first maintenance time and maintenance cycle vary for different cars; some cars require it at only 2,000 kilometers, while others may need it at up to 8,000 kilometers. This variation is due to differences in the specific technical conditions of the vehicles.
7
4
Share

How to Pass Through Highway Toll Stations for Beginners

Methods for beginners to pass through highway toll stations: Before entering the toll station, drivers should closely observe the overhead light signals in the lanes and choose an entrance with a green light. Reduce speed and proceed in an orderly queue, avoiding rushing or competing for lanes. When approaching the toll booth, position the vehicle as close as possible to the toll kiosk, aligning the driver's side window with the toll window to facilitate cash, ticket, or pass card transactions between the toll collector and driver. Toll stations are generally located in two configurations: one is directly on the main highway, also known as barrier-type, typically used at the start or end points of tolled highway sections; the other is situated at interchanges or connecting ramps, commonly employed at grade-separated intersections between tolled highway segments to control vehicles entering or exiting the mainline from intersecting roads.
15
2
Share

What is the size of the photo for a driver's license?

The photo for a driver's license is 3.2cm × 2.2cm. Below is relevant information about the driving test: Definition of driving test simulation fee: The simulation fee and venue fee refer to the costs required for simulating the test at the examination venue. During the process of obtaining a driver's license, apart from the registration fee, simulation fee, and venue fee, there are no other costs. However, the decision to take the simulation test or not is entirely up to the individual—you can choose to simulate or not. Driving test: Applicants for a motor vehicle driver's license must pass the following four subjects: Subject 1—Road traffic safety laws, regulations, and related knowledge test; Subject 2—Venue driving skills test; Subject 3—Road driving skills test; and Subject 4—Safe and civilized driving knowledge test. The test sequence follows Subject 1, Subject 2, Subject 3, and Subject 4 in order. Only after passing the previous subject can one proceed to the next subject's test.
20
5
Share

Will changing lanes over a solid line on an elevated road definitely be captured by cameras?

Changing lanes over a solid line on an elevated road will definitely be captured by cameras. Precautions for lane changing: Lane changing must not affect other vehicles: On roads with two or more motor vehicle lanes in the same direction, the vehicle changing lanes must not affect the normal operation of motor vehicles in the relevant lanes. Turn signals must be used in advance: When turning left, changing lanes to the left, preparing to overtake, leaving a parking spot, or making a U-turn, the left turn signal must be activated in advance; when turning right, changing lanes to the right, returning to the original lane after overtaking, or parking by the roadside, the right turn signal must be activated in advance. Regulations clearly stipulate: When turning, changing lanes, overtaking, making a U-turn, or parking by the roadside, motor vehicles must activate the turn signal 100 to 50 meters in advance. Frequent lane changes are prohibited: Yield to vehicles in the lane being entered; drive in order and avoid frequent lane changes. Turn signals must be used when entering or exiting highways: When entering a highway from an on-ramp, motor vehicles must activate the left turn signal and enter the lane without obstructing the normal operation of vehicles already on the highway. When exiting a highway, motor vehicles must activate the right turn signal, enter the deceleration lane, and exit after reducing speed.
20
2
Share

Where is the cabin air filter located on the 4008?

The cabin air filter of the 4008 is located under the glove compartment on the passenger side. The removal steps are as follows: 1. Remove the decorative panel on the left side of the passenger footwell, pry open the small cover and unscrew the screw; 2. There are three clips on the left side of the decorative panel, which can be removed with a little force; 3. Open the panel below the glove compartment, there are three clips, pull out the small round button in the middle of the clips, remove the clips and then take off the decorative panel; 4. Pull out the black tube, open the white cover to see the cabin air filter, then remove the old one for replacement. In terms of power, the 4008 is equipped with a 2.0L naturally aspirated engine, with a maximum power of 110kW and a peak torque of 198Nm. The transmission system is paired with a 6-speed CVT gearbox. Its dimensions are 4340mm in length, 1800mm in width, and 1625mm in height, with a wheelbase of 2670mm.
10
1
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.