What Are the Causes of Excessive Wind Noise in Cars?

1 Answers
MacEmilia
07/24/25 11:22pm
Excessive wind noise in cars is primarily caused by large sealing gaps in the four doors. The solution is to add soundproofing strips at the door panel joints to reduce wind noise. Car maintenance methods include: 1. Avoid prolonged exposure to sunlight; 2. Replace engine oil and oil filter; 3. Replace oil filter element, air filter element, fuel filter element, air conditioning filter element, and transmission oil filter element; 4. Add windshield washer fluid, antifreeze, and air conditioning refrigerant; 5. Check for wear on the drive belt; 6. Clean throttle valve and cylinder carbon deposits; 7. Inspect the chassis for damage; 8. Check the body and tires. The benefits of car maintenance are: 1. Ensuring optimal performance of the car; 2. Improving driving safety; 3. Reducing engine noise; 4. Extending the car's service life.
Was this review help?
5
5
Share
More Forum Discussions

What to do if the car's side turn signal falls off?

Methods for handling a fallen car side turn signal: It needs to be reinstalled or replaced at a repair shop. The turn signal is a primary device indicating a vehicle's dynamic information, installed at the front and rear of the car body. It activates when the car turns, providing safety for driving. For driving safety, please use the turn signal as required to inform others of the car's movement in advance, allowing them to make correct judgments. The turn signal is an important indicator light that activates when a motor vehicle turns to alert surrounding vehicles and pedestrians. The turn signal tube uses a xenon tube, controlled by a single-chip microcomputer circuit, with left and right alternating flashes for continuous operation. The turn signal employs a flasher to achieve light blinking. Turn signals can mainly be divided into three types: resistance wire type, capacitor type, and electronic type.
12
5
Share

How to Connect the ACC of a Dash Cam?

The connection method for the ACC of a dash cam is: 1. Open the ACC cover plate and measure the wiring position, usually at the fuse location; 2. Route the wire in reverse from the rearview mirror, leaving a certain length of wire end; 3. Open the sealed soft rubber and insert the wire into it; 4. Open the ACC cover plate and route the wire inside; 5. Connect the red wire to ACC, and if parking monitoring is required, connect it to constant power. The black wire can be connected to the negative terminal or grounded. The functions of a dash cam are: 1. It can record video images and sound of the entire driving process; 2. It can serve as parking monitoring; 3. It can provide footage to assist in accident handling.
1
0
Share

Is it necessary to install a blind spot mirror?

Blind spot mirrors are necessary to install as they provide a more intuitive view of areas that cannot be observed by regular mirrors. The functions of a blind spot mirror are: 1. It allows drivers to better observe the side of the vehicle and the condition of the rear wheels while seated in the car, reducing the risk of accidents; 2. It helps in better understanding road conditions when parking or reversing; 3. It enables drivers who frequently travel on mountain roads, rugged terrain, or narrow sections to more effectively adjust the distance between the right side of the vehicle and the road. The determining factors for rearview mirror visibility include: 1. The distance between the eyes and the rearview mirror; 2. The effective area of the rearview mirror; 3. The radius of curvature of the rearview mirror; 4. The tilt angle of the rearview mirror relative to the line of sight; 5. The distance between the rearview mirror and the ground.
5
2
Share

What model of Land Rover was involved in Yu Yuexian's accident?

Yu Yuexian's accident vehicle was the domestically produced SUV Range Rover Evoque model under the Chery Jaguar Land Rover brand. Judging from the vehicle's wheel rims and taillights, it was the 2016 or 2017 SE Zhiyao edition model. Below is an extended introduction to it: Brand Introduction: The Land Rover Range Rover is an imported mid-to-large-sized SUV, and at the same time, it is a model that signifies status, a symbol for successful individuals. The Land Rover Range Rover possesses formidable off-road capabilities, though it may not necessarily be used for off-roading; it offers a very high-end interior atmosphere and enjoyment experience, but in reality, these are not the most important aspects. The most crucial thing is that it can give people a very strong sense of presence and imposing aura.
19
2
Share

At What Age Can You Get a Motorcycle License?

The requirement for obtaining a motorcycle license is that the applicant must be a Chinese citizen aged between 18 and 60 years old, meeting the identity conditions stipulated in Article 9 of the 28th Order of the "People's Republic of China Motor Vehicle Driving License Management Measures" by the Ministry of Public Security, and not holding any other motor vehicle driving license. Below is a detailed introduction to the age requirements for different types of driving tests: Applying for urban buses, trolleybuses, or trams: Between 20 and 50 years old. Applying for large trucks: Between 20 and 60 years old. Applying for tractor vehicles: Between 22 and 50 years old. Applying for medium-sized passenger vehicles: Between 21 and 60 years old. Applying for large passenger vehicles: Between 22 and 60 years old.
13
3
Share

What is the difference between 30 and 40 engine oil viscosity?

The differences between 30 and 40 engine oil viscosity are: 1. 30-grade oil has lower viscosity than 40-grade; 2. 30-grade oil is suitable for higher ambient temperatures than 40-grade; 3. 30-grade oil has better fluidity than 40-grade, which can further reduce fuel consumption; 4. 40-grade oil provides better stability than 30-grade. The functions of engine oil are: 1. To separate the surfaces of relatively sliding parts, thereby reducing wear; 2. To bring heat back to the oil tank and then dissipate it into the air to help the radiator cool the engine; 3. To circulate carbon deposits, sludge, and worn metal particles from engine parts back to the oil tank, flushing away contaminants generated on the working surfaces of parts through the flow of lubricating oil.
19
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.