What are the causes of engine vibration in the Qin Plus-DMI?

1 Answers
DiRylee
07/29/25 6:23pm
dmi engine vibration can be caused by severe engine carbon buildup, ignition system failure, or unstable oil pressure, as detailed below. Severe engine carbon buildup: The most common cause of car vibration is a dirty throttle body or excessive carbon deposits in the fuel injectors. When there is too much carbon buildup inside the engine, the gasoline sprayed by the cold-start injector is largely absorbed by the carbon deposits, resulting in an overly lean air-fuel mixture during cold starts and making it difficult to start. Ignition system failure: Check the condition of the spark plugs, high-voltage wires, and ignition coils. Poor performance of the ignition system or spark plugs can also lead to such issues. Unstable oil pressure: If you have already cleaned the engine carbon deposits, cleaned the throttle body, and replaced the spark plugs but still notice body vibration at idle, you can check whether the fuel supply pressure and intake pressure sensors are functioning properly. Abnormal fuel pump supply pressure or incorrect readings and poor performance of the intake pressure sensor can also cause body vibration.
Was this review help?
20
5
Share
More Forum Discussions

How to Master Clutch Control?

Correct techniques for controlling the clutch: 1. Avoid unnecessary clutch pressing: During normal driving, the clutch is in a fully engaged state without slippage. Clutch disengagement is controlled by pressing the clutch pedal. Except for starting the car, shifting gears, and low-speed braking, avoid keeping your foot on the clutch pedal unnecessarily. Prolonged foot placement on the clutch pedal while driving can easily cause clutch slippage, clutch plate burning, and in severe cases, damage to the clutch pressure plate, flywheel surface, or even annealing of the clutch pressure spring. 2. Apply proper force when pressing the clutch: Avoid using only your toes or lifting your heel off the floor to prevent insufficient force or slipping. Press the clutch pedal all the way to the floor to ensure complete disengagement and prevent wear from prolonged partial engagement. 3. Correct operation during starting: The key to clutch pedal operation when starting is "quick initial press, slow engagement, and coordinated movement." Before starting, it's advisable to test the clutch pedal once to familiarize yourself with its free play, working travel, and pedal feel.
5
0
Share

What Drives the Lavida?

The Lavida is equipped with front-wheel drive across all its models. Here are some relevant details: 1. The front-wheel drive system has relatively lower manufacturing costs, occupies less space, and has a lower failure rate. Maintenance and repair costs in the long run are also lower, which is why it is adopted in most vehicles. Of course, some off-road vehicles use a four-wheel drive system to further enhance off-road capability and driving stability. 2. The Lavida is a compact sedan produced by SAIC Volkswagen. In terms of body dimensions, the Lavida measures 4670*1806*1474mm (L*W*H). 3. In terms of power, the Lavida offers a choice of a 1.5L naturally aspirated engine, a 1.2L turbocharged engine, and a 1.4L turbocharged engine. The 1.5L naturally aspirated version delivers a maximum horsepower of 112, the 1.2L turbocharged version 116, and the 1.4L turbocharged version 150.
11
0
Share

How to activate the windshield washer on a Mercedes-Benz C200?

Wishing you all the best
7
1
Share

What does it mean to charge a 12-volt battery with insufficient power by driving?

Possibilities of charging with insufficient power by driving are as follows: 1. The generator's output voltage is lower than the battery voltage: The generator is not working or there is a fault in the power supply line. In this case, the battery is supplying power while the vehicle is moving, and the generator and charging circuit should be inspected and repaired at a repair shop as soon as possible. 2. Belt breakage: The alternator belt is broken. 3. Generator: The alternator has a serious malfunction. The car can still operate normally when the battery indicator light is on for the following reasons: 1. Stored electrical energy: The car can continue to use the electrical energy stored in the battery until the battery is depleted. 2. After depletion, no part of the car will work: When the battery indicator light is on, the car can still be driven to the garage, which will not damage any components. However, it is necessary to reach the garage before the battery is completely depleted and the car stalls.
20
4
Share

How to Solve the Weak Power Issue of the Old Mazda6?

The reasons and solutions for the weak power of the old Mazda6 are as follows: 1. Poor fuel quality and clogged fuel lines: Filling the car with low-quality gasoline (such as mixtures with excessive impurities) is a common cause of this issue. Excessive impurities in gasoline can easily lead to carbon deposits, and in severe cases, clog the fuel lines, resulting in poor fuel supply and reduced power. In this case, it is necessary to clean the fuel lines and switch to higher-quality gasoline. 2. Excessive carbon deposits and spark plug wear: Excessive carbon deposits on the valves and intake pipes are the most common causes of reduced power in cars. The solution is to seek professional auto repair services to clean the carbon deposits and check if the spark plugs need replacement. 3. Dirty throttle body: The throttle body controls the engine's air intake, and its opening angle has a standard value. If this standard is not met, it can lead to abnormal fuel injection, causing power loss or instability. It is recommended to clean the throttle body during routine car maintenance and check if the air filter needs replacement.
13
3
Share

How to reset the maintenance reminder after servicing a Volkswagen?

Insert the key and wait. Press and hold the 'set' button on the dashboard. Turn on the power switch (do not start the engine). Wait for 10 to 15 seconds. After 10-15 seconds, immediately press the button to the left of the 'set' button to clear the maintenance light. Start the engine, and the wrench icon will disappear, indicating the maintenance reminder has been successfully reset.
2
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.