What are the causes of engine shaking?

1 Answers
MacKeegan
07/25/25 9:13pm
Engine shaking causes: 1. Severe engine carbon buildup. 2. Ignition system issues. 3. Aging engine components. 4. Unstable oil pressure. Common symptoms when engine shaking occurs include: vibration at idle and poor acceleration. Below are solutions for engine shaking: 1. For severe carbon buildup causing vehicle vibration (most commonly due to dirty throttle body or excessive injector carbon deposits), clean the fuel system and inspect the idle air control valve for carbon deposits, cleaning immediately if found. 2. For ignition system problems, check the condition of spark plugs, high-voltage wires, and ignition coils. Poor ignition system performance or weak spark plug firing can also cause such issues. In this case, inspect spark plugs for excessive carbon buildup and replace if necessary. 3. For aging engine components, engine shaking may also relate to worn engine mounts (also called rubber mounts). Replace components when this occurs. 4. For unstable oil pressure, check oil pressure and replace components if needed.
Was this review help?
10
5
Share
More Forum Discussions

Why Does the Steering Shaft Make Abnormal Noises?

Abnormal noises from the steering shaft may be caused by insufficient lubrication of the steering column, leading to increased friction. Below is an introduction to the correct methods of using the steering wheel: 1. Avoid turning the steering wheel while stationary: Refrain from turning the steering wheel when the vehicle is stationary. Try to steer only after the vehicle is in motion. Turning the steering wheel while stationary should only be used occasionally in specific situations, such as maneuvering out of a parking spot. 2. Return the steering wheel to the center position: When the vehicle comes to a stop, the steering wheel should be returned to the center position to prevent unnecessary load on the suspension system and tires. 3. Make turns in one smooth motion: When making a U-turn, try to avoid turning the steering wheel to its maximum limit.
18
1
Share

What is the problem with the U1313 fault code?

Fault code U1313 indicates an issue with the camshaft position sensor. Below is a detailed introduction: 1. Camshaft: The camshaft is a component in a piston engine. Its function is to control the opening and closing of the valves. Although in a four-stroke engine, the camshaft's speed is half that of the crankshaft (in a two-stroke engine, the camshaft's speed is the same as the crankshaft), its speed is generally still very high, and it needs to withstand significant torque. Therefore, the design requirements for the camshaft in terms of strength and support are very high. 2. Sensor: A sensor is a detection device that can sense the measured information and convert it into electrical signals or other required forms of information output according to certain rules. This meets the requirements for information transmission, processing, storage, display, recording, and control.
8
4
Share

What Causes Loud Transmission Noise?

Transmission noise can be attributed to the following specific reasons: 1. Severe carbon buildup: Carbon deposits can cause incomplete combustion of gasoline, leading to engine shaking. Engine carbon buildup significantly impacts the vehicle, making cold starts difficult, meaning the engine struggles to ignite. Severe combustion chamber carbon buildup can even cause cylinder knocking, produce noises during low-speed acceleration, damage pistons and crankshafts, and lead to engine overheating, severely compromising vehicle safety. 2. Overloaded transmission operation: Overloading the transmission can degrade the quality and frictional properties of transmission fluid, increasing friction and wear, which results in transmission noise. Additionally, sludge (contaminants or dirt) can form inside the transmission (e.g., in the valve body), causing issues like jerking, gear slippage, impact, slipping, abnormal noises, delays, overheating, and oil leaks. If not addressed promptly, the transmission may be rendered useless.
20
4
Share

Where is the Jetour Production Plant Located?

Jetour production plant is located in the Henan Intelligent Manufacturing Base. Jetour is a vehicle product series launched by Chery Holding Group, and all Jetour models are SUVs. The Jetour lineup includes models such as the X70, X70S, X90, and X95. Jetour has established an intelligent, electrified, interconnected, and lightweight scalable platform called iPeL. The Jetour X90 is a six-seat SUV model with dimensions of 4840mm in length, 1925mm in width, and 1745mm in height, and a wheelbase of 2850mm. The Jetour X90 features a family-style front grille with LED headlights, keyless entry, power-folding mirrors, rain-sensing wipers, a power-sensing tailgate, 20-inch alloy wheels, a panoramic sunroof, and dot-matrix daytime running lights with tomahawk-style decorative elements.
11
2
Share

What should be the tire pressure for Haval H6?

Generally, the tire pressure should be between 2.2-2.5 bar; however, driving conditions should also be considered. For example, in summer, the tire pressure can be appropriately reduced by 0.1 bar, while in winter, it can be increased by 0.1-0.2 bar. Additionally, the tire pressure should be adjusted based on frequent driving conditions. Below is an introduction to the tire pressure system of Haval H6: The Haval H6 is equipped with a Tire Pressure Monitoring System (TPMS), which can monitor wheel pressure and temperature in real-time and provide an alarm when abnormalities are detected. When the tire pressure is too high/too low or the temperature is too low, the warning light on the instrument panel will illuminate, accompanied by an alarm sound. In such cases, sudden turns and emergency braking should be avoided.
18
4
Share

Can You Keep Driving When the Car Overheats?

When the engine temperature is too high, you must stop immediately to check the situation. Continuing to drive can easily damage the engine and may even require major repairs. To determine if the car is overheating, check these three indicators: 1. The temperature gauge. 2. The temperature warning light. 3. Whether there is steam coming out. The temperature warning light is particularly important because it is conspicuous and easy to notice—it will light up first before the engine overheats. Common causes of overheating include: 1. Low coolant level. This should be the first thing you check, and it’s often the only thing you can inspect yourself. If you’re on a highway or in a remote area without coolant, you can temporarily use water as a substitute. 2. A dirty radiator. The radiator has many small gaps formed by cooling fins, which can easily get clogged with debris, dust, or mud, reducing airflow and cooling efficiency.
6
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.