What are the causes of BYD's one-key start failure?

How to Write the Letter for China V?

China V is represented by the letter V. Below is an introduction to China V: 1. China V refers to the vehicle emission standard, officially known as the National Fifth Stage Emission Standard for Motor Vehicle Pollutants, or "China V Standard". 2. The emission control level of China V Standard is equivalent to the European Union's Euro 5 emission standard currently in effect. The EU has been implementing this standard since 2009, which imposes stricter limits on nitrogen oxides, hydrocarbons, carbon monoxide, and particulate matter emitted by motor vehicles. 3. In the early 1980s, China issued a series of emission standards for vehicle pollution control, including the "Idle Emission Standard for Gasoline Vehicles", "Free Acceleration Smoke Emission Standard for Diesel Vehicles", "Full-Load Smoke Emission Standard for Automotive Diesel Engines", and their measurement standards. This marked the gradual establishment of China's vehicle emission standards. On July 1, 2001, China introduced its first-stage emission standard, modeled after the European emission standards, followed by China II, China III, China IV, and China V. Each stage has stricter emission requirements than the previous one. Additional Information: The symbols for China I to China VI are: China I, China II, China III, China IV, China V, China VI.

11

4

Share

What is the principle of the crankshaft position sensor in a car?

The principle of the crankshaft position sensor is to determine the position of the crankshaft, specifically the rotation angle of the crankshaft. It typically works in conjunction with the camshaft position sensor to determine the basic ignition timing. Below is a detailed introduction to the automotive crankshaft position sensor: 1. The crankshaft position sensor is used to detect engine speed, piston top dead center, and the rotation angle of the crankshaft. These parameters are the main control parameters for calculating the air-fuel ratio of the mixture and performing ignition adjustments. 2. The crankshaft position sensor sends these parameters as signals to the engine control unit. If the crankshaft position sensor fails and the signal cannot trigger the electronic ignition (or ECU) to work, the engine will not receive an ignition command and will not inject fuel, making it impossible to start the engine. 3. The engine control unit uses the information provided by the crankshaft position sensor to generate ignition timing signals and injection pulses, which are then sent to the ignition coil and fuel injector, respectively. 4. The crankshaft position sensor is one of the most important sensors. If it is damaged and cannot output the missing tooth position signal, the engine control module (ECM) will be unable to determine the crankshaft position, causing the fuel system and main relay system to fail to operate.

16

1

Share

How long does a PDI inspection take?

When picking up a new car, the PDI inspection generally takes about 40 minutes. More information about PDI is as follows: 1. PDI is the abbreviation for Pre-delivery-Inspection. It refers to the inspection before delivery. Typically, vehicles undergo a thorough inspection before being handed over to the owner to check for any issues caused by prolonged storage or damages during transportation. 2. PDI inspection is a free inspection conducted by the 4S store for new cars about to be delivered to the owner. It is performed by relevant staff of the 4S store and is a mandatory inspection procedure that dealers must complete before delivering the new car to the consumer. The higher the grade of the car and the higher the level of electronic automation, the more PDI inspection items there usually are.

6

1

Share

Does the odoff light indicate fuel saving or fuel consumption?

When the odoff light is on, it indicates fuel saving. The light signifies that the engine auto start-stop system is active, which significantly saves fuel for the engine. Compared to the fuel consumption per 100 kilometers, it can save at least one to two liters, but the exact amount depends on the vehicle model. Introduction to the car's od key: 1. When quick overtaking is needed, pressing the od key drops the gear to 3rd, increasing engine speed and torque, allowing for faster acceleration when stepping on the throttle. 2. When driving at low speeds in congested urban areas, activating odoff limits the transmission to gears within 3rd, reducing unnecessary switching of internal shift solenoids, while keeping the vehicle in a lower gear also aids in acceleration. 3. When the vehicle is going downhill, activating odoff limits the transmission to gears within 3rd, utilizing engine braking to assist in slowing down and reducing the need to apply the brakes.

13

5

Share

What to Do When Your Car Won't Start Due to Dead Battery?

Here are the solutions for a car that won't start due to a dead battery: 1. Push-start the car manually. 2. Replace the car battery. 3. Recharge the battery. 4. Jump-start the car with jumper cables, ensuring positive to positive and negative to negative connections. 5. Use another vehicle to tow-start the car. Additional information on the effects of a depleted car battery: 1. Battery depletion shortens the battery's lifespan. 2. It prevents the car from starting and causes electrical devices in the car to malfunction. 3. Starting attempts may result in loss of data in the vehicle's control modules, leading to operational failure. 4. It causes overheating of the starter motor, reducing its lifespan. 5. Prolonged battery depletion can damage the alternator.

6

5

Share

What are the differences between high-end and standard car configurations?

The most obvious difference between high-end and standard car configurations is that, for the same displacement, the price of the high-end version is higher than that of the standard version. The high-end model has richer configurations compared to the standard model. Below is an introduction to car configurations: 1. Car configurations generally include basic configurations, safety configurations, driving assistance configurations, external configurations, internal configurations, and information and entertainment configurations. Basic configurations focus on three main components: the engine, transmission, and chassis. 2. The engine typically depends on parameters such as displacement, torque, number of cylinders, environmental standards, power, naturally aspirated or turbocharged, etc. Normally, for the same engine type, the larger the displacement, the stronger the power and torque, the better the driving quality, the more cylinders (within the engine's capacity range), the newer the environmental standards, and the better the power output. 3. Transmissions include DCT, AT, MT, and CVT. AT transmissions are relatively older but have strong reliability. Choosing AT and CVT is usually more practical. 4. The chassis is generally divided into independent suspension and non-independent suspension. Independent suspension is certainly superior to non-independent suspension, but the price will be relatively higher.

12

4

Share

What are the causes of BYD's one-key start failure?

How to Write the Letter for China V?

What is the principle of the crankshaft position sensor in a car?

How long does a PDI inspection take?

Does the odoff light indicate fuel saving or fuel consumption?

What to Do When Your Car Won't Start Due to Dead Battery?

What are the differences between high-end and standard car configurations?

What does releasing the handbrake mean?

What does 'mirror' mean on a car?

What is an In-Vehicle T-BOX?

Is the M gear for climbing hills or high speed?