What are the causes of abnormal tire noise?

1 Answers
VonEmersyn
07/30/25 9:06am
The causes of abnormal tire noise are: 1. Dirt stuck on the surface of the car tire; 2. Small stones stuck in the tread grooves of the tire; 3. A nail puncturing the car tire; 4. Worn-out brake pads; 5. Excessive tire pressure; 6. Aging of the tire surface; 7. Loose tire bolts. The solutions for abnormal tire noise are: 1. Clean the surface and tread grooves of the tire; 2. Check the tire pressure; 3. Inspect if the brake pads are too thin; 4. Ensure the tire bolts are tightened properly; 5. Replace the tire. The functions of a tire are: 1. Transmitting driving force, braking force, and steering force to operate the vehicle; 2. Supporting the vehicle load; 3. Reducing and absorbing vibrations and impacts during driving.
Was this review help?
1
3
Share
More Forum Discussions

Reasons for the Electronic Parking Brake System Warning Light to Illuminate?

The reasons for the electronic parking brake system warning light to illuminate are: 1. ABS function failure; 2. Severe brake pad wear, leading to failure; 3. Brake fluid does not meet requirements. The principle of the electronic parking brake is: When parking, after the driver operates the electronic button of the electronic parking brake system, the electronic control unit will control the motors integrated in the left and right brake calipers to act, driving the brake caliper pistons to move and generate mechanical clamping force to complete parking. The method of using the electronic parking brake is: 1. Activate the electronic parking brake by stepping on the brake pedal and pulling up the electronic parking brake switch until the indicator light on the dashboard lights up, and the handbrake switch indicator light also lights up; 2. Deactivate the electronic parking brake by pressing the electronic parking brake switch while stepping on the brake, and the indicator lights on the dashboard and switch will turn off.
17
5
Share

What Causes Transmission Whining?

Reasons for transmission whining: Excessive meshing clearance in the transmission. When the meshing clearance is too large, the driving gear impacts the driven gear during rotation, producing a knocking sound. This noise typically worsens as the transmission temperature rises. Gear noise can also result from damaged gear tooth surfaces, which creates an uneven sound. The louder the throttle, the more pronounced the noise becomes, and in severe cases, vibration in the transmission may be felt. Below is relevant information about transmission fluid: 1. Inspection method: The method for checking automatic transmission fluid differs from engine oil. Engine oil is checked when the engine is cold, whereas transmission fluid should be preheated to approximately 50°C before inspection. 2. Replacement interval: Automatic transmission fluid replacement follows a specific cycle. Due to the extremely precise internal control mechanisms and small fitting clearances in automatic transmissions, most manufacturers recommend changing the transmission fluid every two years or 40,000 to 60,000 kilometers.
8
2
Share

What are the symptoms of a faulty canister purge valve?

The symptoms of a faulty canister purge valve are as follows: 1. The fuel nozzle shuts off prematurely during refueling, or there is a gas ejection when opening the fuel tank cap; 2. Fuel vapor or dripping fuel is observed at the canister's atmospheric vent; or upon removing the canister, it is found to be filled with gasoline. 3. Poor acceleration, jerking movements, and unstable idle speed that fluctuates up and down; 4. Engine stalling and failure to start, accompanied by unusual noises while driving. 5. When disconnecting the oil tank's pipe, one can feel intermittent suction at the canister's connection port, with a frequency of about two to three times per second; if there is no suction, it indicates that the canister purge valve is stuck in the closed position. 6. Unplugging the canister purge valve's connector: if the suction stops, the valve is functioning normally; if suction persists, it means the valve is stuck in the open position.
7
3
Share

Where is the airbag control module located in a Honda CR-V?

The airbag control module in a Honda CR-V is generally located in front of the gear shift lever or underneath it. Below is some relevant information about the Honda CR-V: 1. Exterior: The new Honda CR-V adopts Honda's latest family design language, featuring a more rugged styling. The large chrome strip on the front grille is particularly eye-catching, and the sharp-looking LED headlights on both sides connect seamlessly with the grille. 2. Interior: The new Honda CR-V has become more refined with added technological elements. The cabin extensively uses soft plastic materials, and the passenger seat area is wrapped in leather, aiming to narrow the gap in material quality with mainstream competitors. 3. Powertrain: The new Honda CR-V is equipped with a 1.5T turbocharged engine, delivering a maximum power of 142kW and a maximum torque of 243N·m, paired with a CVT continuously variable transmission.
1
4
Share

Is it necessary to replace all valves if one is damaged?

It is necessary to replace all valves if one is damaged. The working principle of valves is: when the crankshaft rotates, it drives the piston to move up and down in the cylinder, which in turn drives the camshaft via a chain or belt. The cam lobes on the camshaft then push against the valves to control their opening and closing. Symptoms of dirty valves include: 1. Engine shaking at idle; 2. Insufficient power during driving; 3. Increased fuel consumption; 4. Engine stalling easily; 5. Emissions failing to meet standards. The method for cleaning valves is: 1. Open the hood and remove the intake pipe leading to the valves; 2. Turn the ignition key and press the accelerator pedal; 3. Spray cleaning agent onto a cloth and clean the inside of the valves; 4. Wipe the valves repeatedly until clean.
10
3
Share

What does it mean when the TC light is on in a Buick business vehicle?

When the TC light is on in a Buick, it indicates a fault in the vehicle's traction control system. Possible causes for the TC light being on include: 1. Solenoid valve: A malfunction in the solenoid valve; 2. Filter screen: Dirty engine oil clogging the solenoid valve's filter screen; 3. Gear and impeller: Wear in the actuator gear and impeller leading to oil pressure leakage and triggering an alarm; 4. Dirty throttle: The engine computer misjudging a TC fault. Additional relevant information is as follows: 1. Introduction: Buick is an automobile brand under General Motors, founded in 1900 in Detroit, Michigan, USA. 2. Features: Buick is known for its high horsepower, individuality, practicality, and maturity. Its models include the Excelle, Regal, LaCrosse, GL8, Highlander, Enclave, Encore, and others.
6
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.