What are the button functions of the 2021 Hyundai Tucson?

Where is the crankshaft position sensor located on the Mercedes-Benz 272 engine?

The crankshaft position sensor on the Mercedes-Benz 272 engine is located on the transmission clutch housing, at the rear left side of the engine block. Working principle of the crankshaft position sensor: It determines the position of the crankshaft, specifically the crankshaft's rotation angle. It typically works in conjunction with the camshaft position sensor to establish the basic ignition timing. The sensor detects engine speed, piston top dead center position, and crankshaft rotation angle - these parameters are crucial for calculating the air-fuel ratio of the mixture and regulating ignition timing. Functions of the crankshaft position sensor: Detects engine speed (hence also called the speed sensor); detects piston top dead center position (thus also known as the top dead center sensor), including detecting top dead center signals for each cylinder for ignition control and the first cylinder's top dead center signal for sequential fuel injection control.

9

1

Share

Differences Between Toyota A25A and A25C Engines?

The differences between Toyota Camry's A25A and A25C engines are as follows: 1. Version Differences: A25A represents Toyota's TNGA 2.5L engine, which is imported from Japan. The A25C engine, on the other hand, is the domestically produced version. 2. Assembly Differences: The A25A is imported as a complete engine assembly, fully assembled in Japan before being shipped. The A25C involves importing all necessary engine parts from Japan, which are then assembled at the GAC Group factory. 3. Performance Differences: Both the A25A and A25C engines feature new technology that allows free switching between the Otto cycle and Atkinson cycle systems, achieving a compression ratio of 13:1 for this internal combustion engine. In terms of new technology and power performance, the 2.5L engine delivers 240 nM of torque and 151 KW (205 horsepower), providing robust power for the new vehicle. The 4-2-1 exhaust manifold arrangement takes exhaust separation to a new level.

9

4

Share

What are the differences between Geely Emgrand and Vision?

Differences between Geely Emgrand and Vision: 1. Different vehicle dimensions: Emgrand: Vehicle dimensions: Length 4631mm, width 1789mm, height 1470mm, wheelbase: 2650mm. Vision: Vehicle dimensions: Length 4599mm, width 1747mm, height 1482mm, wheelbase: 2615mm. 2. Different powertrains: Emgrand: The new Geely Emgrand is equipped with a 1.3T-GeTec-DVVT turbocharged engine, featuring front-wheel drive, with a maximum power of 98kw, turbo intervention at 1800 rpm, and peak torque output of 185NM at 2000 rpm. Vision: The new Vision is powered by a 1.5L-DVVT high-efficiency and energy-saving engine. This engine utilizes DVVT intelligent continuous variable intake and exhaust timing technology, delivering a maximum power of 80kW/6000rpm and a maximum torque of 140Nm/4400rpm. It can be paired with a mature and reliable 5MT or an intelligent automatic transmission to form the powertrain.

13

2

Share

Which is More Fuel-Efficient: Automatic or Manual Transmission Cars?

Manual transmission cars are more fuel-efficient than automatic ones. The primary reason automatic transmissions consume more fuel under the same conditions is due to the hydraulic torque converter in their gearbox, which loses some energy during operation. Most manual transmission vehicles use gearbox shifting, which offers high mechanical transmission efficiency with minimal delay, resulting in very high output efficiency. Automatic transmission cars rely on transmission fluid and hydraulic torque converters for power transfer, leading to greater transmission losses. For vehicles of the same brand, model, and displacement, manual transmissions generally offer slightly better fuel economy than automatics. However, this is not an absolute rule, as many factors influence fuel consumption, such as road conditions, fuel quality, driving habits, and vehicle condition. The biggest difference between manual and automatic transmission cars is that manual transmissions allow drivers to shift gears at will, while automatic transmissions are controlled by the system. To maximize fuel efficiency in a manual transmission car, avoid high-RPM driving whether following traffic or cruising normally. Generally, maintaining around 2000 RPM is the optimal speed for fuel economy.

16

1

Share

Do vehicles require annual inspections after six years?

Private cars must undergo annual inspections after six years. Small and micro non-commercial passenger vehicles require inspection once every two years within the first six years; after six years, once per year; and after 15 years, once every six months. According to the motor vehicle inspection regulations issued in 2014, inspections were required annually after six years. However, under the new inspection rules effective October 22, 2020, non-commercial small and micro passenger vehicles aged between six and ten years now require biennial inspections instead of annual ones. For private vehicle inspections, you need to bring the vehicle's registration certificate, the owner's ID card, and the compulsory traffic insurance policy. The vehicle must be equipped with a fire extinguisher, warning triangle, and reflective vest. All lights must function properly, the exterior must be undamaged, all aftermarket modifications must be removed, and there should be no outstanding traffic violations or unresolved accidents. If the vehicle fails the inspection, the staff will inform the owner of the specific issues. The owner must then address these problems at a repair shop. The primary reason for inspection failure is usually non-compliance with exhaust emission standards.

1

3

Share

What Causes Abnormal Noise from Car Tires?

Abnormal noise from car tires can be caused by nails or debris puncturing the tire, or brake pads being too thin. Nails or debris puncturing the tire: The noise occurs once per tire rotation, resembling something tapping the ground, with the rhythm accelerating as the vehicle speed increases. If it's a stone, simply prying it off will suffice. If it's a nail, you can drive directly to a repair shop for a tire patch as long as the tire pressure remains stable in urban areas. Brake pads being too thin: Front wheel brake pads on cars generally have electronic sensors, while rear wheels typically do not, but most have mechanical warning indicators. When the brake discs become too thin, they produce a metallic grinding sound. The noise is slight when not braking but becomes louder and more piercing when the brakes are applied. In such cases, you must drive slowly to replace the brake pads. For most wheels, the thickness of the brake pads can be observed through the gaps in the rim. When the estimated thickness is less than 3 millimeters, they must be replaced.

20

5

Share

What are the button functions of the 2021 Hyundai Tucson?

Where is the crankshaft position sensor located on the Mercedes-Benz 272 engine?

Differences Between Toyota A25A and A25C Engines?

What are the differences between Geely Emgrand and Vision?

Which is More Fuel-Efficient: Automatic or Manual Transmission Cars?

Do vehicles require annual inspections after six years?

What Causes Abnormal Noise from Car Tires?

What is the difference between forged wheels and cast wheels?

Will an Automatic Transmission Car Move Without Pressing the Accelerator?

Is It Necessary to Press the Brake When Shifting Between D and N Gears?

Is the timing belt or chain used in the 2017 Besturn B50?