What are the body dimensions of the Trumpchi GE3?

What is the working principle of a torque sensor?

Working principle of torque sensor: It uses strain gauge electrical measurement technology to form a strain bridge on an elastic shaft for torque measurement. Application scope of torque sensor: 1. Detection of output torque and power of rotating power equipment such as motors, engines, and internal combustion engines; 2. Detection of torque and power of fans, water pumps, gearboxes, and torque wrenches; 3. Can be used to manufacture viscometers; 4. Can be used in process industries and flow industries. Precautions for installing torque sensors: 1. Do not operate with electricity, and never directly strike or collide with the sensor; 2. The fastening bolts of the coupling should be tightened, and a protective cover should be added outside the coupling to avoid personal injury.

4

1

Share

What Causes the Rattling Noise in a Car Door Limiter?

Door limiter rattling noise is caused by wear and tear of the limiter. Applying some oil to the limiter for lubrication can resolve the issue. Below is the related introduction: Introduction to Door Opening Limiter: Commonly referred to as the limiter, it is a device that restricts the rotation of the door when subjected to a certain force. Function of the Door Opening Limiter: It limits the extent to which the door can open. On one hand, it restricts the maximum opening of the door to prevent it from opening too wide. On the other hand, it keeps the door open when needed, such as when the car is parked on a slope or during windy conditions, preventing the door from closing automatically.

7

0

Share

How to Remove Crankshaft Bolts with Primitive Methods?

Insert two steel bars into the holes, then use a pry bar to leverage the two steel bars to loosen the bolts. Alternatively, measure the hole distance and weld an F-shaped wrench. Below is an introduction to the crankshaft: 1. Introduction: The crankshaft is the most important component in an engine. It receives the force from the connecting rod and converts it into torque, which is then output through the crankshaft to drive other engine accessories. 2. Function: The crankshaft is subjected to the combined effects of centrifugal force from rotating masses, periodically varying gas inertial forces, and reciprocating inertial forces, causing it to bear bending and torsional loads. 3. Requirements: The crankshaft must have sufficient strength and stiffness, with journal surfaces that are wear-resistant, operate uniformly, and have good balance.

19

4

Share

Does the Tesla Model X have four-wheel drive?

Tesla Model X has four-wheel drive. The 2020 Tesla Model X comes in two models: the Long Range and the Performance, both of which are four-wheel drive. The front motor of the 2020 Tesla Model X Long Range has a maximum power of 202 kW and a maximum torque of 404 Nm, while the rear motor has a maximum power of 285 kW and a maximum torque of 440 Nm. The front motor of the 2020 Tesla Model X Performance has a maximum power of 202 kW and a maximum torque of 404 Nm, and the rear motor has a maximum power of 375 kW and a maximum torque of 650 Nm.

19

4

Share

How to Reset the Maintenance Light on Dongfeng Honda Jade?

Method to reset the maintenance light on Dongfeng Honda Jade: 1. With the engine off, press and hold the short-distance trip meter reset button located below the tachometer. 2. Turn the ignition switch to the ON position, then release the trip meter reset button. The display will show the SERVICE indicator. 3. Pull out the minute button on the clock and turn it clockwise. The odometer reading will appear on the display. 4. Reset the engine maintenance reminder. 5. Turn the ignition switch to the ON position again, and the SERVICE indicator will disappear. The dimensions of the Dongfeng Honda Jade are 4660mm in length, 1775mm in width, and 1500mm in height, with a wheelbase of 2760mm.

18

4

Share

Can a Dash Cam Still Record After Being Turned Off?

When the dash cam is turned off, it cannot record. The functions and usage precautions of a dash cam are as follows: Functions of a Dash Cam: A dash cam is used to record driving and driving status information, as well as images and sounds during the journey, providing evidence in the event of traffic accidents or disputes. Precautions for Using a Dash Cam: Regular data processing is necessary to prevent inconvenience caused by data loss. Additionally, for the data already recorded by the dash cam, it is essential to copy it promptly, migrate and save the data to avoid difficulties in subsequent queries or the inability to verify the data if it is lost.

6

0

Share

What are the body dimensions of the Trumpchi GE3?

What is the working principle of a torque sensor?

What Causes the Rattling Noise in a Car Door Limiter?

How to Remove Crankshaft Bolts with Primitive Methods?

Does the Tesla Model X have four-wheel drive?

How to Reset the Maintenance Light on Dongfeng Honda Jade?

Can a Dash Cam Still Record After Being Turned Off?

How to Replace the Battery in an Audi Key?

How to Deal with Paint Peeling on a White Car?

How to adjust the time on a 2009 Peugeot 307?

Should I Top Up or Replace the Antifreeze When It's Low?