What are the body dimensions of the Toyota E'Z?

What Does It Mean When the Engine Emission System Warning Light Comes On?

When the engine emission system warning light comes on, it indicates a fault in the emission system. Here are the specific details about the engine exhaust system warning light: 1. False Alarm Handling: Start and turn off the vehicle three times in a row, or disconnect the negative terminal of the engine battery, wait for 30 seconds, and then reconnect it. After performing the above steps, check if the engine warning light on the dashboard is still on. This method only applies to false alarms in the engine system. 2. Cause of the Fault: The engine exhaust system warning light often comes on due to poor fuel quality in the country. It may be caused by a damaged oxygen sensor in the three-way catalytic system or poisoning of the catalytic converter. If the light comes on while driving, immediately reduce speed and drive to the nearest service station for inspection. 3. Solution: If the warning light comes on and the vehicle cannot start after being turned off, this is usually due to a fuel pump or ignition system failure—call for a tow truck immediately. If the vehicle can still be driven but exhibits severe shaking, loss of acceleration power, or other symptoms, take action to prevent further engine damage.

19

0

Share

What are the effects of a faulty purge pump?

The impacts of a faulty purge pump are as follows: 1. Reduced vehicle power: A damaged purge pump prevents fuel vapor from the charcoal canister from entering the cylinders, leading to a lower concentration of combustible air-fuel mixture in the engine, which results in decreased vehicle power output; 2. Increased fuel consumption: If the charcoal canister becomes saturated with fuel vapor and the purge pump fails to expel it, subsequent fuel vapor cannot be recycled, naturally causing an increase in vehicle fuel consumption; 3. Environmental pollution: The direct release of fuel vapor into the atmosphere causes air pollution. Additionally, during normal engine operation, it may inhale pure air instead of fuel vapor, leading to an overly lean air-fuel mixture.

2

Share

What are the differences between Michelin Primacy 4 and 3ST?

Here are the main differences between Michelin Primacy 4 and 3ST: 1. Drainage performance: Michelin Primacy 4 features a new tread design through Evergrip technology, increasing the drainage space by over 50% compared to the 3ST. Don't underestimate the drainage function of tires. As the saying goes, "Prepare against danger in times of safety," the drainage performance of car tires is extremely important. On rainy days, a layer of water film equivalent to a lubricant forms between the tire and the road surface, making hydroplaning more likely. Good drainage performance can significantly reduce the occurrence of such situations. 2. Rubber compound: Michelin Primacy 4 adopts a new rubber compound with excellent braking performance, resulting in naturally better wet braking distance. Official data shows that Michelin Primacy 4 outperforms the 3ST by a full 2.4m in wet braking distance. It's worth noting that even 0.1m can potentially prevent a major accident, so to some extent, it also enhances driving safety.

2

3

Share

How to reset the wrench light on Shuailing T6?

Here are the methods to reset the wrench light on Shuailing T6: 1. Use the button on the car dashboard, press and hold the reset button for 5-10 seconds to clear the wrench symbol. 2. Access the vehicle computer system and reset it through the maintenance settings. Here is some related information about the Shuailing T6 wrench light: 1. The wrench symbol on the car dashboard is a maintenance reminder light. When this light comes on, it indicates that the vehicle needs maintenance. 2. The maintenance reminder light is quite convenient for managing the vehicle's maintenance cycle. 3. After completing the vehicle maintenance, the maintenance reminder light should be reset immediately. Failure to do so may cause memory confusion and disrupt the vehicle's maintenance cycle.

5

0

Share

What is the reason for the ABS warning light to return to normal after restarting?

ABS warning light returning to normal after restarting may be due to the following reasons: 1. Front wheel slippage: When driving on icy or snowy roads, if the front and rear wheels rotate differently while braking simultaneously, the ABS light may illuminate; 2. Sensor interference: If the ABS wheel speed sensor's sensing area on the wheel is covered by contaminants such as mud or dirt, it can affect the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle speed and calculating the wheel slip rate, thereby failing to issue appropriate commands to adjust braking; 3. Brake system malfunction: If both the ABS and parking brake lights illuminate simultaneously, it indicates a potential serious issue with the vehicle's braking system. In such cases, you should not continue driving. Immediately reduce speed, pull over to the roadside, and contact a repair shop for assistance.

10

0

Share

What does a 6-speed wet dual-clutch transmission mean?

6-speed dual-clutch transmission refers to the vehicle being equipped with a six-speed dual-clutch transmission. Below is an introduction to transmissions: 1. Classification: Common types of automotive automatic transmissions include four types: hydraulic automatic transmission (AT), continuously variable transmission (CVT), automated manual transmission (AMT), and dual-clutch transmission (DSG). The most widely used is AT, which has almost become synonymous with automatic transmissions. 2. Function: The engine's output speed is very high, with maximum power and torque occurring within a certain speed range. To optimize engine performance, a transmission system is necessary to coordinate the engine's speed with the actual driving speed of the wheels. 3. Features: (1) Change the transmission ratio to expand the range of torque and speed variations of the driving wheels, adapting to frequently changing driving conditions while allowing the engine to operate under favorable conditions (higher power and lower fuel consumption); (2) Enable the vehicle to reverse while maintaining the engine's rotation direction; (3) Utilize neutral gear to interrupt power transmission, allowing the engine to start, idle, and facilitating gear shifting or power output.

2

5

Share

What are the body dimensions of the Toyota E'Z?

What Does It Mean When the Engine Emission System Warning Light Comes On?

What are the effects of a faulty purge pump?

What are the differences between Michelin Primacy 4 and 3ST?

How to reset the wrench light on Shuailing T6?

What is the reason for the ABS warning light to return to normal after restarting?

What does a 6-speed wet dual-clutch transmission mean?

What are the hidden features of Geely Emgrand?

Should You Release the Handbrake Before or After Engaging the Gear?

Where are the sunroof drainage outlets of the Geely Emgrand EC7?

How to Clean Air Conditioning Water Stains on Car Windows?