What are the body dimensions of the new Accord?

What are the methods to deal with rust spots on car paint?

After wiping off the rust spots, you can use a fine needle or toothpick to apply matching paint, or use a touch-up pen. It is recommended to go to a 4S shop for touch-up and polishing treatment. Polishing: The coarseness of the polishing wax used depends on the degree of oxidation of the car paint. If the particles of the sand wax are relatively coarse, it is suitable for grinding off deeper scratches, but it causes greater damage to the car paint. Although polishing has a relatively obvious effect, it should not be used frequently. Frequent polishing of the car will thin the car paint, directly affecting the service life of the car paint surface. Touch-up pen: Although the touch-up pen cannot remove the rust spots on the car paint, it can cover the rust spots to some extent. It can be said to treat the symptoms but not the root cause. It can be used for emergencies, but it is also necessary to clean the vehicle in time to prevent rust spots on the car paint surface.

9

3

Share

Bumper Damaged: Replace or Repair with Paint?

It needs to be replaced, but it also depends on the situation. Main reasons: If the front bumper is cracked, you can choose to repair or replace it based on the extent of the damage. If the cracked area is small, it can be welded and repaired. If it exceeds the repair standard, replacement is necessary. For metal bumpers, whether welding or repainting is required, professional tools and skilled techniques are essential. Typically, repairs need to be done at a 4S shop, as personal repairs may not meet the required standards. Introduction to bumpers: The car bumper is a safety device designed to absorb and mitigate external impacts, protecting the front and rear of the vehicle. The front and rear bumpers of a car are usually made of plastic, hence they are referred to as plastic bumpers. Generally, a car's plastic bumper consists of three parts: the outer panel, cushioning material, and crossbeam. The outer panel and cushioning material are made of plastic, while the crossbeam is formed from cold-rolled thin steel sheets pressed into a U-shaped groove. The outer panel and cushioning material are attached to the crossbeam.

18

3

Share

What are the tips for selecting reference objects when driving in a straight line?

Generally, reference objects refer to trees, lamp posts, and road edge lines on both sides of the road. As long as the selected reference objects are parallel to the road markings, they can be used. Here are some precautions for driving in a straight line: 1. Vision: Don't focus only on the near distance. To keep the vehicle moving straight ahead, you must learn to look far ahead while using peripheral vision to monitor the front of the vehicle, rearview mirrors, and surrounding vehicles. 2. Speed: It's essential to control the speed when driving straight. Driving too slowly can actually cause the vehicle to veer off course. If there is a vehicle ahead, maintain a safe distance and slow down in advance if necessary. After completing straight-line driving, brake promptly. 3. Steering wheel: If the vehicle tends to drift while driving straight, some might think not moving the steering wheel will prevent drifting. However, road conditions, unbalanced wheel alignment, and uneven suspension support can all cause the steering wheel to drift. Even without moving it, the vehicle may gradually drift, so fine adjustments are necessary.

5

3

Share

What are the standards for reverse parking?

The standards for reverse parking are as follows: Failure to follow the prescribed route sequence, disqualification; Vehicle body crossing the line, disqualification; Failure to fully enter the parking space, disqualification; Before reversing, if both front wheel contact points do not exceed the control line, disqualification; Exceeding the 210-second time limit for the task, disqualification; Stopping for more than 2 seconds mid-process, 5-point deduction per occurrence. The passing area for the Subject 2 garage is 16 meters in length and 6.83 meters in width. The garage dimensions are 5.25 meters in length and 2.31 meters in width. Students must refer to the ground markings and operate the vehicle in the prescribed route sequence to correctly enter and exit the garage from both sides of the test area. Only after both front wheel contact points exceed the control line at one end of the road can the vehicle proceed to reverse into the garage for parking; then move forward to exit the garage and proceed toward the control line on the other side of the road, stopping once both front wheel contact points exceed the control line, then reversing into the garage again for parking; finally, exit the garage and return the vehicle to the starting position, leaving the test area. Except for parking in the garage, no stopping is allowed during the process. The vehicle body must not cross the line. The task must be completed within 210 seconds. During the reverse parking operation, the driving speed should be controlled, using first gear or reverse gear at idle speed throughout, maintaining consistent speed from start to finish. After controlling the steering timing, observe carefully during the reversing process, grasp the key points of steering, and turn the wheel at the appropriate time. Additional extended information is as follows: U-turn reversing: U-turn reversing should be performed in areas where U-turns are permitted (such as highways, intersections, street entrances, etc.), and should be based on the width of the road and the density of vehicle traffic. When performing a U-turn reverse on a wider road, the position of the rear of the vehicle or the wheels on the road can be judged directly from the rearview mirror. On narrow roads, if the position of the rear and rear wheels cannot be accurately judged from the rearview mirror, open the door and observe the rear wheels while operating. If multiple forward and reverse movements are needed, step out to check the safe distance between the road and the wheels to prevent falling into a ditch. In areas with high vehicle traffic density, a person should be assigned to direct the operation. When performing a U-turn reverse at an intersection or street entrance, appropriately expand the visibility and range behind the vehicle, accurately judge the movements of passing vehicles, pedestrians, and bicycles, and reverse cautiously to prevent accidents. Garage reversing: Garage reversing is generally performed when the vehicle returns to the parking garage or enters a temporary parking lot for parking. For vehicles with good visibility (such as light buses, cars, large buses, etc.), the reversing can be judged directly by observing through the rear window. If visibility is poor and the rear cannot be seen clearly (such as fully loaded trucks, etc.), open the door and judge the position of the vehicle body in the garage from one side, while observing the other side of the vehicle body from the rearview mirror to prevent scraping the vehicle or other vehicles. Turning reversing: When performing a turning reverse, the driver should pay attention to judging the situation on the inside of the turn and behind the vehicle, observe both sides of the vehicle body from the rearview mirror, and pay attention to the timing of turning the steering wheel to prevent rear-end collisions and vehicle body scrapes. Shifting reversing: This is generally performed when entering a narrow parking space or when needing to shift left and right to avoid oncoming traffic on a narrow road. This method sometimes requires multiple reversals, so be careful about the width of the shifted position, and judge the position of the rear of the vehicle, both sides of the vehicle body, and the rear wheels to prevent collisions, scrapes, or falling into ditches. If necessary, have someone direct the operation from behind the vehicle.

13

1

Share

Location of Sagitar Windshield Washer Fluid

The location of the Sagitar windshield washer fluid is on the lower right side of the engine compartment. Below is a detailed introduction to the Sagitar: 1. Interior: The dashboard is entirely wrapped in soft materials. 2. Features: Includes cruise control, sunroof, keyless entry/start, four-way adjustable leather steering wheel, leather seats, lumbar support adjustment, cornering lights, heated mirrors, etc. The chassis feels solid, heavy, and resilient. 3. Fuel Consumption: The 1.4T model has a combined fuel consumption of around 7L per 100km, which can drop below 6.5L on highways, making it an excellent performer overall.

19

2

Share

How to Identify Genuine Burmester Car Speakers?

Burmester car speakers can be identified by their welding craftsmanship and built-in magnets. Here are the relevant details: 1. Differences: Genuine German Burmester speakers have square-shaped strong neodymium magnets at the back, with a hollow design in the center; the speaker terminals of Burmester are flat in design and feature excellent welding craftsmanship. 2. About Burmester: Burmester, founded in 1978, rapidly rose in the German High-End audio industry. It has now become one of the world's most respected manufacturers of high-quality stereo systems.

3

0

Share

What are the body dimensions of the new Accord?

What are the methods to deal with rust spots on car paint?

Bumper Damaged: Replace or Repair with Paint?

What are the tips for selecting reference objects when driving in a straight line?

What are the standards for reverse parking?

Location of Sagitar Windshield Washer Fluid

How to Identify Genuine Burmester Car Speakers?

Do Dash Cams Have Sound?

Which Cars Have Strong Climbing Power and Are Fuel-Efficient?

Is 360-Degree Panoramic View Camera Practical?

How long should the engine be turned off in traffic jams