What are the body dimensions of the Dongfeng A9?

1 Answers
Michelle
07/29/25 8:58pm
The Dongfeng A9 measures 5066 mm in length, 1858 mm in width, and 1470 mm in height, with a wheelbase of 2900 mm. The Dongfeng A9 is a mid-to-large-sized sedan. Compared to the Audi A6L, which is positioned as a luxury mid-to-large-sized sedan, although there is a certain gap in wheelbase, the body width and height are very close to the A6L, and the body length is even 51 mm longer than the A6L. Below is an introduction to the model: The Dongfeng A9 is equipped with a 1.8-liter turbocharged engine across the entire lineup. This engine has a maximum power of 150 kW, a maximum torque of 280 Nm, a maximum power speed of 5500 rpm, and a maximum torque speed ranging from 1400 to 4000 rpm. This engine features CVVT technology and direct fuel injection, and uses an aluminum alloy cylinder head and block. It is paired with a 6-speed automatic transmission. The Dongfeng A9 uses a MacPherson independent suspension at the front and a multi-link independent suspension at the rear.
Was this review help?
10
2
Share
More Forum Discussions

How to Repair a Flooded Car?

Here are the steps to repair a flooded car: 1. Remove seats, doors, and interior. Take out all vehicle seats, transmission decorative covers, carpets, etc., and clean up the water inside. 2. Repair or replace wiring. Replace the wiring harnesses of electronic components such as audio systems, air conditioning control panels, ABS modules, etc. 3. Clean the engine and transmission. First, drain the water from the engine cylinders and intake manifold. For the transmission, disassemble and clean components like the valve body and torque converter. After cleaning, assess the damage and replace the engine or transmission if severely affected. 4. Replace the onboard computer. The onboard computer includes the engine control unit, transmission control unit, airbag control unit, ABS control unit, etc. 5. Handle other aspects. This includes cleaning mud from the chassis and addressing headlight components.
7
3
Share

What does the red exclamation mark on the dashboard mean?

The red exclamation mark on the dashboard indicates a brake system malfunction. If this warning light illuminates, first check whether the handbrake is fully released. If the light remains on after releasing the handbrake, inspect whether the brake fluid level is normal or if the brake pads are excessively worn. If braking performance hasn't diminished, drive cautiously and proceed to the nearest repair shop immediately, as brake conditions directly impact driving safety. When the brake system warning light activates, you must stop and inspect the vehicle immediately regardless of circumstances. The brake system is critically important to drivers - any brake-related issues require immediate resolution.
6
4
Share

What does it mean when the prompt 'failed to smoothly shift gears as instructed' appears during Subject 3?

In Subject 3, the prompt indicating a failure to smoothly shift gears means that the clutch was not fully depressed during gear shifting. Below are the relevant operation instructions for gear shifting: 1. Upshifting operation: After starting in first gear, appropriately press the accelerator to increase speed before upshifting. When accelerating to 15~20 km/h, shift to second gear. During gear shifting, release the accelerator pedal, depress the clutch pedal, move the gear lever to the neutral position, then release the clutch pedal. After releasing, depress the clutch pedal again, push the gear lever into second gear, and then slowly release the clutch while gradually pressing the accelerator pedal to smoothly increase speed. The same method applies to other upshifting operations. 2. Downshifting operation: When downshifting is needed, release the accelerator pedal, depress the clutch pedal, push the gear lever into neutral, then release the clutch pedal. Lightly press the accelerator to increase engine speed (a light press is sufficient, do not exceed 3000 rpm), then depress the clutch pedal again, push the gear lever into a lower gear, and slowly release the clutch until the left foot completely releases the clutch. Then, press the accelerator to control the car's speed in the new gear. During downshifting, you can skip one gear but must not skip two gears. Downshifting can be used when descending long slopes and needing to slow down using engine idle speed.
15
1
Share

Can I Get the First Maintenance Before Reaching 5,000 Kilometers?

It is possible to get the first maintenance before reaching 5,000 kilometers. Below is an extended introduction about the first maintenance: 1. Meaning: The first maintenance of a car refers to the initial service after the new car has been driven. The timing of the first maintenance varies by vehicle, typically performed after driving 3,000-5,000 kilometers. Many brand 4S shops, aiming to shorten customers' maintenance cycles, have adjusted to remind customers to perform maintenance at 5,000 kilometers or 3 months. 2. Items: Replace engine oil, oil filter, gasoline filter, and air filter. Check whether the level of the car's coolant meets the specified requirements, the levels of brake and clutch fluid, whether the oil level in the power steering fluid reservoir meets the specified requirements, check for oil leaks at all oil pipe interfaces in the system, the levels of battery fluid and windshield washer fluid reservoir, the tension and aging of the belts of the generator, air conditioner, water pump, and power steering pump, whether the front and rear lights of the car are complete (including: headlights, marker lights, turn signals, brake lights, reverse lights, and fog lights), the tire pressure and wear of the car tires, tighten the tire bolts to the specified torque, supplement the tire pressure to within the specified value for the model, perform tire rotation based on wear conditions, and whether the car's exhaust emissions meet standards, etc.
7
0
Share

How to Use Car Cruise Control?

To activate and use cruise control, follow these steps: 1. Press the CRUSE button to activate the cruise module. 2. When the dashboard displays CRUSE, the vehicle must reach a speed of at least 40 km/h to enable cruise control. Once above 40 km/h, press the SET button to activate cruise control. 3. Speed adjustments can be made using the '+' and '-' buttons. Push the lever upward to increase speed and downward to decrease speed. Holding the lever will rapidly increase or decrease the speed. 4. Pressing the accelerator or pushing the lever downward will temporarily cancel the function. Releasing the accelerator or pushing the lever inward will automatically restore the function. The CANCEL button is used to deactivate cruise control.
16
5
Share

Is it possible to overtake on highway curves?

Overtaking on highway curves is possible. Below are specific guidelines for overtaking on highways: 1. Observe road conditions: Before overtaking, assess the road ahead and choose a flat, straight section if possible. Simultaneously, check the adjacent lane by looking at the left rearview mirror to ensure no vehicle is approaching from behind. Wait until any overtaking vehicle has passed before proceeding. Additionally, observe whether the vehicle ahead also intends to overtake. 2. Activate turn signals: Once conditions permit, turn on the left turn signal, then flash headlights and sound the horn to alert the vehicle ahead. If the vehicle ahead signals to yield, steer left to overtake. 3. Return to original lane: If already in the adjacent lane, downshift and press the accelerator firmly to increase engine speed and boost power. After accelerating past the vehicle ahead and maintaining a safe distance, activate the right turn signal, check the right rearview mirror for safety, and then return to the original lane.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.