What are the body dimensions of the Changan CS75?

What are the precautions after replacing brake pads?

Here are the precautions to take after replacing brake pads: 1. Observation: The thickness of a new brake pad (excluding the steel backing plate) is generally around 10mm. When the visible thickness of the brake pad is reduced to about 1/3 of its original thickness (approximately 3mm), the owner should increase the frequency of self-inspection and be prepared to replace them. Typically, when the thickness is less than about 1mm, immediate replacement is required. Each brake pad has a raised indicator on both sides, with a thickness of about 2-3mm, which is the minimum replacement limit for the brake disc. If the brake pad thickness is level with this indicator, experienced drivers advise replacing them immediately. 2. Listen for sounds: If a metallic scraping sound (like iron rubbing against iron) is heard when lightly applying the brakes, it is recommended to replace the brake pads immediately. This indicates that the limit indicators on both sides of the brake pads are directly rubbing against the brake disc, showing that the pads have exceeded their limit. In such cases, while replacing the brake pads, it is also necessary to inspect the brake discs. Often, by the time this sound occurs, the brake discs may already be damaged. Even after replacing the brake pads, the noise may persist, and in severe cases, the brake discs may need to be replaced as well. 3. Feel the braking force: As brake pads wear thin, the braking performance is affected. You may need to press the brake pedal deeper to achieve the same braking effect that was previously achieved with a lighter press. The initial braking effect may noticeably weaken. If you feel that your brakes have become softer or less effective, it's time to check if the brake pads need replacement.

14

2

Share

What is the maximum age limit for obtaining a driver's license?

The maximum age limit for obtaining a driver's license is 70 years old. Below are some important considerations for taking the driver's license test: 1. Don't forget to release the handbrake when starting: When first learning to drive, always follow the correct sequence when starting the car. Regardless of whether the handbrake was engaged when parking, always check and release the handbrake before starting. 2. Always fasten your seatbelt: Good habits start with wearing a seatbelt. Although seatbelts may feel uncomfortable, in the event of a high-speed collision, this small belt can save your life. 3. Don't forget to engage the handbrake when parking: This issue is similar to wearing a seatbelt. During practice sessions, the training area is usually flat, and since students take turns driving, instructors may not emphasize this. However, failing to overcome this bad habit can lead to serious problems during actual driving. A moment of carelessness can result in the car rolling, causing damage to your vehicle and potentially harming others' property or even lives. The mistake may seem small, but the consequences can be severe. 4. Position your right foot correctly: Driving school cars often have a higher idle speed. Instructors usually discourage students from pressing the accelerator during initial lessons, and many even disconnect the throttle cable. Since the car moves at idle speed, it's very slow, and sometimes pressing the clutch can stop the car immediately. Over time, many students develop the habit of leaving their right foot idle. This habit can lead to panic in emergencies when driving a manual transmission car, causing delays in finding the brake pedal and potentially leading to accidents where the accelerator is mistakenly pressed instead of the brake. 5. Don't forget to shift to neutral when exiting the car: Forgetting to shift back to neutral or Park after stopping can cause the engine to stall. If you also forget to engage the handbrake, the car might lurch forward, causing damage to yourself or others.

12

3

Share

What is the recommended tire pressure for Audi Q5?

Audi Q5's normal tire pressure range is 2.4-2.5bar. Due to seasonal factors, the tire pressure can be appropriately increased by 0.2bar in winter and decreased by 0.1bar in summer. This data is based on the international GBT2978-2008 standard. How to check tire pressure in Audi Q5: Start the car and enter the interior; locate the central display screen inside the car and touch the 'cae' button on the left; enter the vehicle settings menu, select the tire settings option in the vehicle settings; in the tire settings, click on tire monitoring to view the tire pressure. Generally, a tire pressure above 2.8bar is considered too high, and below 2.0bar is considered too low. Hazards of over-inflated tires: Reduced friction and adhesion of the tires, affecting braking performance; causes steering wheel vibration and deviation, reducing driving comfort; accelerates wear on the central tread of the tire, shortening tire lifespan; increases vehicle vibration, indirectly affecting the lifespan of other components; overextends the tire cords, reducing elasticity and increasing the load on the car during driving. Hazards of under-inflated tires: Increases friction coefficient with the road, leading to higher fuel consumption; makes the steering wheel heavy and prone to deviation, compromising driving safety; increases movement of tire parts, causing abnormal heat due to excessive rolling; reduces the functionality of cords and rubber, leading to delamination or cord breakage and excessive friction with the rim, damaging the tire bead area and causing abnormal wear; multiplies friction with the ground, rapidly increasing tire temperature, softening the tire, and drastically reducing its strength. High-speed driving may lead to tire blowouts. If the tire pressure monitoring indicator lights up (a yellow symbol, an irregular circle with no seal on top, four small spikes below, and an exclamation mark inside), there are generally three possible reasons: Abnormal tire pressure: Usually alerts when below 1.8bar or above 3.0bar. In this case, tire inspection and pressure adjustment are required. Tire pressure monitoring not reset: After inflating the tires, the tire pressure was not reset in time, causing the system to still record the previous data, thus lighting the indicator. Simply perform a tire pressure reset. Damaged tire pressure sensor: The sensor, which monitors tire pressure and is installed inside the tire connected to the inflation valve, may be damaged if the tire is hit while driving, causing the tire pressure warning light to turn on. For sensor damage, only a complete replacement is possible.

20

1

Share

Is it necessary to file for a car spoiler installation?

Filing is required. Below is the relevant information about installing a car spoiler: 1. Reason: Installing a car spoiler is considered an alteration of the car's appearance, and the owner must file for registration with the vehicle management office in advance. If the car spoiler is installed privately without filing, the public security traffic management department will detain the vehicle, confiscate the illegal device, order restoration to the original state, and impose a fine according to the law. After the modification is completed, the vehicle license must be re-photographed and replaced to ensure that the photo on the license matches the modified vehicle, ensuring that the car can pass annual inspections and routine safety checks after modification. The requirement for installing a spoiler is that after installation, the spoiler should not exceed the overall dimensions of the vehicle. 2. Main function of a car spoiler: The main function of a car spoiler is to provide sufficient downforce, reduce the lift at the rear of the vehicle, and ensure that the car remains firmly on the road, maintaining sufficient stability during driving.

3

0

Share

How to Identify a Faulty Oxygen Sensor?

Cars with damaged oxygen sensors may experience reduced power performance, significantly increased fuel consumption, rapid deterioration of the three-way catalytic converter, and a greatly shortened lifespan of the catalytic converter. Below is relevant information about oxygen sensors: 1. Introduction: The oxygen sensor is an essential component for reducing exhaust pollution in engines. Once the air-fuel ratio of the mixture deviates from the theoretical value, the oxygen sensor detects the oxygen concentration in the exhaust and sends feedback to the ECU. This feedback controls the fuel injection amount of the injector, thereby maintaining the air-fuel ratio of the mixture within the normal range. The oxygen sensor calculates oxygen concentration through chemical equilibrium to monitor the air-fuel ratio of the mixture. Therefore, if the oxygen sensor is damaged, it cannot monitor the vehicle's exhaust emission values. 2. Core Component: The core component of the oxygen sensor is a porous ZrO2 ceramic tube. At certain temperatures, high-concentration oxygen molecules inside the tube can be adsorbed to form electrons, creating a potential difference.

20

4

Share

How to Adjust the Seats in the Borgward BX5?

The rear seats of the Borgward BX5 cannot be adjusted. For the front seats, there is a handle located directly beneath the seat that can be pulled forward or backward to adjust the seat position, and the backrest can also be reclined. Below is a detailed guide on adjusting the Borgward BX5 seats: 1. Backrest Angle: After sitting in the car, move your hips backward to adopt a standard sitting posture and first adjust the backrest angle. The backrest should not be reclined too far, as this can increase driving hazards and reduce reaction time in emergencies. The correct angle is slightly more than 90 degrees between the backrest and seat cushion, with the body leaning slightly backward to aid relaxation. For long-distance driving, it's advisable to place a cushion to fill the gap between the lower back and the seatback, alleviating back pain and enhancing comfort. 2. Seat Height: Adjust the seat height to ensure the steering wheel does not obstruct your view. Ideally, raise the seat as high as possible for a broader field of vision, improving driving safety. However, maintain a distance of at least one and a half fists (or at least one fist) between your head and the roof to prevent head bumps on rough roads. 3. Seat Position (Front/Back): Experienced drivers often prefer to move the seat backward. However, the optimal position is determined by whether you can easily press the pedals fully. This ensures comfortable driving and allows the airbag to deploy effectively in case of an accident. 4. Headrest: Position the headrest at the back of your head for maximum safety. This prevents neck strain while driving and protects the vulnerable neck area from injury.

11

0

Share

What are the body dimensions of the Changan CS75?

What are the precautions after replacing brake pads?

What is the maximum age limit for obtaining a driver's license?

What is the recommended tire pressure for Audi Q5?

Is it necessary to file for a car spoiler installation?

How to Identify a Faulty Oxygen Sensor?

How to Adjust the Seats in the Borgward BX5?

Which Factory Produces Lincoln Vehicles

Is it necessary to carry a fire extinguisher in a car?

What is the Normal Temperature Range for Car Air Conditioning?

What do the gear letters in an automatic car represent?