What are the benefits of independent throttle bodies?

1 Answers
SanXavier
07/30/25 12:39am
Automobiles benefit from using independent throttle bodies in the following ways: 1. Independent throttle bodies can increase the engine's air intake efficiency, allowing the engine to achieve higher maximum RPM, thereby providing better power output for the vehicle. 2. Independent throttle bodies are less prone to carbon buildup, which helps extend the engine's lifespan. 3. The throttle body is the first channel for air to enter the cylinder and an important component for regulating the vehicle's power output. Engines with independent throttle bodies do not require air to pass through the intake manifold during intake. Each throttle body is responsible for a single cylinder, significantly improving intake efficiency, resulting in faster throttle response and stronger power for the vehicle.
Was this review help?
8
4
Share
More Forum Discussions

How to align the timing belt of the je4d25q5a engine?

There are timing alignment marks on the engine's timing gear, the front end of the crankshaft, and the flywheel. Rotate the engine crankshaft to position the first cylinder piston at the top dead center. Align the timing mark on the camshaft gear with the timing mark on the chain and secure it. Install the crankshaft drive sprocket and ensure that the timing mark on the chain aligns with the mark on the sprocket. Finally, make sure that the three timing marks on the timing chain correspond with the two timing marks on the camshaft sprocket and the one timing mark on the crankshaft sprocket.
10
2
Share

What is the appropriate cross-sectional area for car battery jumper cables?

Car battery jumper cables are generally 16 square millimeters or 25 square millimeters. Here are the selection criteria for specific situations: 1. Vehicle type: For small cars, the national standard pure copper cable starts at 16 square millimeters. However, for large engineering vehicles, the national standard pure copper cable of 25 square millimeters is recommended. If the value is lower than the recommended standard, it will be difficult to jump-start the engine. 2. Current impact: With constant power and voltage, the thicker the cable, the lower the resistance, resulting in more current being transmitted to the motor. It is advisable to use thicker cables or bundle two thinner cables together. Unless otherwise specified, the standard is usually 16 square millimeters of copper wire, while special cases require 25 square millimeters of copper wire.
1
3
Share

Which country is the production location of Audi cars?

Audi cars are produced in Germany. It is a German luxury car brand, symbolized by four interlocking rings, and is currently a subsidiary of Volkswagen Group. Its headquarters is located in Ingolstadt, Germany, with branches in many countries including China. Audi's main models include the A1, A3, A4, A5, A6, A7, A8, Q1, Q2, Q3, Q5, Q7, Q8, TT, R8, as well as the S and RS performance series. Taking the A3 as an example, the car has a length of 4292mm, a width of 1765mm, a height of 1423mm, and a wheelbase of 2578mm. The optional WiFi hotspot in the car can access the internet via a mobile phone SIM card, enabling real-time updates on flight information and fuel prices.
9
1
Share

How to Deal with Dust in Paint?

First, use 3M 2000# sandpaper, typically folded in half, then separate it from the fold line, and use the soft side of the sanding block to evenly sand the dust spots on the paint. Apply 3M 05973# medium-coarse wax to the sanded area of the paint (i.e., the flawed area) until there is no resistance when touching the paint. Then, use a polishing machine at a speed of 2000 to 3000 RPM to polish the paint until it regains its gloss. Visit the brand service station of the vehicle to have the paint redone, and you can also point out any noticeable flaws for further treatment.
17
0
Share

How to Remove a C-Clip?

There are two types of removal methods for retaining rings. One is the expansion type, and the other is the contraction type. Depending on the shape of the retaining ring or its installation position, select the appropriate tool for removing or installing the ring. For example, retaining ring pliers, which come in two types: for holes and for shafts. Place a retaining ring plier in the gap at the end of the ring and hold the other end of the ring with your hand. Open the pliers and remove or install the ring in place. Place a flat-head screwdriver in the gap at each end of the ring, using two flat-head screwdrivers in total, then gently tap the screwdrivers to install the ring in place.
9
4
Share

Can a licensed car change its license plate?

A licensed car can change its license plate. Generally, there are two situations where a license plate can be changed: 1. Change of vehicle ownership; 2. The car license plate is cloned. After the above situations occur, you can apply for re-licensing at the vehicle management office. The specific methods are as follows: 1. Apply to the traffic management department to cancel the original license plate. After the traffic management department reviews the violations of the driving license and license plate, they will agree to cancel it; 2. Publish a license plate cancellation statement in local newspapers or have the traffic management department issue a cancellation announcement; 3. After 30 days, bring your ID card and the original vehicle purchase invoice to the local traffic management department to complete the new licensing procedures.
6
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.