What are the benefits of crystal coating on car surfaces?

1 Answers
VonEdward
08/29/25 6:16am
There are several benefits to crystal coating on car surfaces: 1. Crystal coating can protect the vehicle from minor daily scratches. Even when external force exceeds the elastic protection range of the coating, it usually only leaves scratches on the coating without damaging the paint. 2. Crystal coating isolates the paint from the external environment, effectively preventing oxidation and resisting corrosion from bird droppings, insect fluids, acid rain, etc. 3. Crystal coating makes the car paint shine like a mirror, making the body easy to clean and maintain. A simple rinse with water can make it look as good as new, saving a lot on car washing costs. 4. Crystal coating can enhance the brightness of the car surface, making the paint look crystal clear and radiant, with a brightness level of over 95% (new cars typically have around 70%). 5. Crystal coating is cost-effective: it not only reduces car washing and waxing expenses but also provides better protection for the original paint. In terms of car maintenance and beauty, crystal coating is quite expensive, but the actual benefits are also very significant.
Was this review help?
13
4
Share
More Forum Discussions

How many kilometers should the PCV valve be replaced?

Replace the PCV valve at 120,000 kilometers. Main function: It directs the gases from the crankcase into the intake manifold through the PCV valve, with a small amount of air entering the intake manifold directly from the air filter via the PCV valve. This prevents phenomena such as icing at the throttle, incomplete combustion, and worsened emissions. Symptoms of a faulty PCV valve in the engine: 1. Engine shaking, unstable idle, and a large amount of white smoke from the exhaust pipe. 2. It may cause oil to remain in the crankcase, leading to corrosion, accelerated wear, and shortened engine life. 3. It can also cause difficulties in starting the engine, idle shaking, lack of power during acceleration, and excessive oil consumption. 4. It is prone to sludge deposits and clogging, which increases the pressure inside the crankcase, causing oil vapors and exhaust gases to flow back into the air filter and contaminate the air filter element.
19
3
Share

How often should the coupling oil be changed?

Coupling oil should be changed every three years. Here are the precautions for coupling oil filling: 1. Oil type: Usually, non-flammable hydraulic oils such as No. 8 hydraulic oil or No. 32 hydraulic oil are used, and gear oil must not be added. Oil filling is strictly prohibited in hydraulic couplings (except for adjustable-speed hydraulic couplings), as it may cause explosions or fires. 2. Oil filling amount: The filling amount should be 70%-80%. For ordinary torque-limiting hydraulic couplings, the filling amount corresponds to 80% of the rated power. Tilt the oil filler at a 45° angle from the vertical direction, and fill until the oil just starts to flow out. Typically, the filling range for YOX-type couplings is 40%~80%.
17
5
Share

What does the turning dotted line mean?

Turning dotted line means turning guide line. The following is the specific introduction of road markings: 1. White solid and broken line: When the broken line is in the middle of the road section, its function is to separate the traffic flow in the same direction or as a line for identifying safe driving distance. When at an intersection, its function is to guide the vehicle forward; When the solid line is in the middle of the road section, its function is to separate motor vehicles and non-motor vehicles traveling in the same direction, or to indicate the edge of the lane. When at an intersection, its function is as a guide lane line or stop line. 2. Double white solid and broken line: When the broken line is in the middle of the road section, its function is as a variable lane line whose driving direction changes over time. When at an intersection, its function is as a yield line. The function of the solid line at an intersection is as a stop line.
16
0
Share

Why does the turn signal not automatically reset?

Turn signals not automatically resetting is due to damaged positioning pins. Here is additional information: 1. Turn signals: Turn signals are the primary devices indicating a vehicle's dynamic information, installed at the front and rear of the car body. They are activated when the car turns, providing safety for driving. Proper use of turn signals allows drivers to anticipate the car's movements in advance and make correct judgments. 2. Turn signal tubes: Turn signal tubes use xenon tubes with a microcontroller-controlled circuit, enabling alternating left-right flashing without interruption. Turn signals employ flashers to achieve light blinking, mainly categorized into resistance wire type, capacitor type, and electronic type.
2
4
Share

What Causes a Scooter to Stall When Accelerating After Starting?

Here are the reasons why a scooter stalls when accelerating after starting: 1. Idle speed too low: This causes the air-fuel mixture to become too lean when accelerating due to a sudden increase in air intake, making it unable to ignite and resulting in stalling. In this case, you can adjust the idle speed appropriately. If your motorcycle's idle speed is normal, this reason can almost be ruled out. 2. The choke switch is not closed before cold starting: Accelerating under this condition can also cause the engine to stall. If your motorcycle's choke switch is not open, this situation can also be ruled out. 3. Carburetor fuel supply issues: Such as a clogged fuel filter or a damaged float chamber switch causing poor fuel supply. When accelerating, the fuel level in the carburetor float chamber drops, but the subsequent fuel supply cannot keep up, leading to stalling. This type of fault usually results in a brief increase in RPM when accelerating, followed by stalling.
7
1
Share

Does Using Third-Party Chargers Affect Tesla?

Tesla may sometimes fail to charge when using third-party chargers. Here is an introduction to relevant Tesla content: 1. Electric Vehicles: Electric vehicles refer to vehicles that use on-board power as their energy source, drive wheels with electric motors, and comply with all road traffic and safety regulations. Due to their relatively smaller environmental impact compared to traditional vehicles, their prospects are widely optimistic, although current technology is not yet mature. 2. Pure Electric Vehicles: Compared to fuel-powered vehicles, the main differences lie in four major components: the drive motor, speed controller, power battery, and on-board charger. Instead of gas stations, they rely on public ultra-fast charging stations. The quality of pure electric vehicles depends on these four components, and their value is also determined by the quality of these parts. The application of pure electric vehicles is directly related to the selection and configuration of these four components.
19
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.