What are the acceptance standards for engine overhaul completion?

1 Answers
IsabelleLee
07/30/25 12:16am
Automobile engine overhaul completion acceptance standards: 1. Good power performance, stable idle operation, reasonable fuel consumption, normal lubrication of components, and proper functioning of accessories. 2. No water leakage, oil leakage, air leakage, or electrical leakage is allowed. 3. The engine should be able to start within 5 seconds at normal temperature, with stable operation at low, medium, and high speeds. Water temperature should not exceed 90 degrees Celsius, with good acceleration performance. 4. There should be no misfiring, carburetor backfiring, or exhaust pipe popping. After stable engine operation, there should be no abnormal noises, but slight and uniform timing gear, engine oil pump transmission gear noise, and valve tappet sounds are allowed. 5. Cylinder pressure must meet specified limits. 6. Engine oil pressure must meet specified limits. 7. Engine emissions must comply with regulations, and minimum fuel consumption must meet specified limits. 8. Painting must be done according to specifications. 9. After passing inspection, the engine must be installed with a speed limiter.
Was this review help?
7
5
Share
More Forum Discussions

What is the failure rate of Audi?

Audi's failure rate is 63 percent. Introduction to automotive failure rate: The automotive failure rate refers to the probability of a vehicle experiencing a failure within a unit of mileage at a certain driving distance, also known as the failure probability or failure degree. It is an important parameter for measuring the reliability of a vehicle, reflecting the degree of loss of working capability during use. Measures to reduce automotive failure rate: To ensure the good technical condition of a vehicle, it is necessary to perform careful maintenance as specified by the manufacturer during use. This includes tightening connections, lubricating lubrication points, readjusting adjustment points, and seasonal maintenance of coolant. To reduce natural degradation, adding protective agents (additives) to the lubrication system, cooling system, fuel system, manual transmission, or automatic transmission can reduce wear and corrosion, effectively extending the service life and preventing failures.
20
4
Share

What brand is catchpower tires?

catchpower is an economical tire under the Windforce Wantuchi Group. The parent company of Wantuchi tires is Qingdao Fengchi Tire Co., Ltd. Fengchi tires are mainly for export, while Wantuchi is a brand created by Fengchi Tire for the Chinese sales market. The Wantuchi catchpower series tires have good wear resistance and comfort. At the same time, the four drainage channels provide excellent driving stability and water drainage for the vehicle. Tires, together with the car's suspension system, cushion the impact forces during driving, providing good ride comfort and smoothness while ensuring excellent adhesion between the wheels and the road. Tires bear the weight of the car, making them one of the most important components of a vehicle. Tire characteristics: The tread of car tires features patterns that enhance performance, along with increased section width and lower internal pressure for better cushioning. Car tires can be structurally categorized into radial tires and bias-ply tires. Tips for choosing tires: Choose new tires of the same size as the original ones. For those who enjoy aggressive driving, tires wear out faster, so opt for more durable ones. For national highways or expressway driving: To ensure maximum safety during high-speed braking, choose tires that offer the shortest braking distances on both dry and wet roads. For comfort during long trips, select tires that provide a comfortable ride (with minimal bumps and noise). For performance, lean towards high-performance tires. For city driving: To handle various urban hazards (like pedestrians crossing the road), choose tires with the shortest braking distances on dry and wet surfaces. For long mileage life, select tires that resist deformation and sliding of tread blocks under engine power or braking forces, which wear down the rubber. Opt for tires with longer mileage life. For fuel economy, tires with lower rolling resistance can significantly reduce fuel consumption. When using catchpower tires daily, pay attention to the following: Regularly check the tire surface for cracks, deformations, or other defects. As tires wear down, the tread grooves gradually become shallow. Worn-out treads lose their water drainage and anti-skid functions, greatly reducing the car's performance. Small cracks can pose a risk of blowouts at high speeds. Also, promptly remove pebbles stuck in the grooves. Park on level ground whenever possible. Avoid parking on roads with thick, sharp, or pointed stones. Do not park near or in contact with petroleum products, acids, or other materials that degrade rubber. After parking, avoid turning the steering wheel, as this accelerates tire wear. Do not splash water to cool overheated tires. In hot weather or during high-speed driving, tires can overheat, increasing air pressure. In such cases, stop to let the tires cool naturally. Never release air to reduce pressure or splash water to cool them, as this can cause abnormal aging of the tread rubber. Avoid sudden braking. Minimize frequent and hard braking to prevent accelerated tread wear from dragging on the road.
16
0
Share

What is the displacement of the BMW x320i?

The BMW x320i has a 2-liter displacement. Factors affecting car displacement: The displacement of a car is determined by the engine. Generally, a larger displacement means the engine releases more energy per unit time (converting chemical energy from fuel into mechanical energy), resulting in better "power performance." Displacement can be considered one of the most important parameters of an engine, as it directly relates to many technical indicators. Ways to reduce car displacement: Drive smoothly and avoid sudden movements. In heavy traffic, maintain a safe distance from the vehicle ahead to prevent panic-induced dangers and avoid emergency braking. Many experienced drivers may not realize this, but emergency braking not only damages the vehicle but also increases fuel consumption. Therefore, avoiding emergency braking offers numerous benefits.
6
1
Share

What is the fuel consumption of the Audi A7?

The fuel consumption of the Audi A7 is 6.5 liters per 100 kilometers. Factors affecting fuel consumption: Incorrect driving habits have the greatest impact on fuel consumption. During driving, especially in heavy traffic, at red lights, or when changing lanes, sudden acceleration and hard braking are the most common issues. Experts have conducted fuel consumption tests during acceleration and found that fuel consumption increases by 2 to 3 times compared to driving at a constant speed. Tips to reduce fuel consumption: If you want to save fuel, avoid frequent lane changes, overtaking, and merging. Besides increasing fuel consumption, these actions also raise the probability of accidents, and each gear shift consumes additional fuel. Even in traffic jams, try to queue in order. Cutting in line will only result in higher fuel consumption.
13
0
Share

What Causes the Noise When Rolling Up/Down BMW 3 Series Windows?

The noise when rolling up/down BMW 3 Series windows may be caused by hardened window seals losing their soft elasticity after prolonged use. During window operation, the hardened seals create friction and squeezing noises against the glass. This issue tends to be more noticeable in summer as aged seals expand more severely under sun exposure, increasing friction and consequently making the noise worse. Solution: In such cases, the seals should be replaced at a repair shop. Another possible cause is excessive dirt in the gap between the glass and seals, where particulate matter in the dust can create noise when rubbing against the glass. Solution: In this situation, using window lubricant for maintenance would be appropriate.
1
5
Share

What causes the Nissan Sunny to jerk at around 40 mph?

There are many possible reasons for the Nissan Sunny to jerk at around 40 mph. The specific causes are as follows: Transmission jerking or impact is often not due to internal valve body damage, but rather the accumulation of stubborn dirt and impurities inside, especially when these contaminants gather in the valve body, forming blockages that prevent effective regulation of oil pressure, leading to jerking, impact, or slippage issues. Solution: The traditional approach is to replace the transmission fluid, which may help but cannot completely resolve the issue. Disassembling and repairing the transmission is not something non-professionals should attempt. However, with advancements in technology, transmission jerking problems can now be addressed through disassembly and repair. Solution: Take the vehicle to a repair shop for professional servicing.
9
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.