···
Log in / Register

What are some car maintenance tips?

1 Answers
CarsonFitz
07/30/25 2:41am

The car maintenance tips are as follows: 1. Spare engine oil: If the car experiences poor acceleration, blue smoke from the exhaust, and the engine oil warning light on the dashboard comes on, it may indicate oil burning. In this case, you can stop the car, open the hood, and check the oil level with the dipstick. If the oil level has decreased, this confirms the issue. If you have spare oil, you can add it and then proceed to the nearest repair shop. If not, it is advisable to call for emergency repair and avoid driving further, as this can cause significant damage to the engine. 2. Jack and portable tire pressure gauge: If you accidentally run over a nail and the tire becomes unusable, first use the tire pressure gauge to measure the pressure. If the pressure hasn't changed much, you can continue driving. If there is a significant drop in pressure, use the jack from the trunk to replace the spare tire. When using the jack, make sure to place it on the lower side rail, which is the sturdy metal body of the car beneath the door between the two tires. Be very careful with this, as improper placement can cause the car to deform under its weight or even slip suddenly during the tire change, leading to irreversible accidents. 3. Dual-purpose wrench and screwdriver: These are tools with two usable ends, making them very versatile. Most screws on headlights and batteries can be loosened with this wrench. The dual-purpose screwdriver has one flat end and one Phillips end, suitable for common screws. 4. Jumper cables: If your car battery dies, you can stop another car for help and use jumper cables to connect the batteries of both cars to start your vehicle immediately. 5. Always carry pure water: Pure water is not just for drinking. If the windshield washer runs out of water or the radiator leaks, you can use it as an emergency solution. When you reach a repair shop, replace the water in the radiator with specialized antifreeze or coolant. 6. Tow rope: A tow rope has many uses and doesn't take up much space in the car. In case of an accident where the car cannot be moved out of danger, having a tow rope allows you to seek help from another vehicle to tow your car to safety if a tow truck is not immediately available.

Was this review help?
18
2
Share
More Forum Discussions

How to solve the problem of BMW X1 air conditioner not cooling?

First, drive with the windows open for a while to equalize the indoor and outdoor temperatures, then close the windows, turn on the air conditioner's internal circulation mode, and set it to the coldest mode with the highest fan speed. If the car air conditioner can still cool, go to a 4S shop to check if there is a lack of refrigerant (Freon). If it is lacking, Freon can be added. It is best to replace the air filter during seasonal changes and perform a cleaning of the air conditioning ducts. For air conditioning circuit issues, check whether the AC switch on the control panel is malfunctioning, whether the main unit's temperature control circuit is normal, and whether the compressor's electromagnetic coil is engaging properly.
16
5
Share

How to Match the Remote Key for Besturn B70?

Park the car and ensure all four doors are closed. Then, open and close the left front door (the main driver's side door) three times. Within three seconds, insert the key and turn it on and off five times consecutively (without starting the engine). Remove the key and press the unlock and lock buttons on the remote. You should hear a response from the remote. After the remote responds, press the unlock and lock buttons on the new remote. The car may experience remote control confusion at this point, requiring a re-matching process. Ensure all four doors are locked, insert the key, and turn it on and off five times within five seconds. Remove the key and press the unlock and lock buttons on the remote twice to complete the process.
18
2
Share

How to Reset the Maintenance Wrench Light on Buick Encore?

Turn off the ignition switch to cut off the power supply to the car. Press and hold the buttons on the dashboard simultaneously, keeping both trip reset buttons pressed for more than 5 seconds. Turn the key to the second position (accessory mode) without starting the engine, and wait until all dashboard lights illuminate. This process typically takes about 10 seconds. Wait for the wrench light to go off. Once it's off, release both trip reset buttons. Turn off the ignition switch and then turn it back on to complete the maintenance reset.
17
1
Share

How to Fix Abnormal Power Window Operation in Honda Vezel?

Open the door where the switch needs to be replaced. For most models, the power window switch area is made of plastic. Carefully examine the seam between the trim panel and door panel to locate the notch. Insert a pry tool or flat tool into the notch to lift the trim panel, then slowly remove the panel along the gap. Disconnect the power window switch connector. Flip the trim panel over, and you should see the switch secured by several cross-head screws. Remove these screws to detach the power window switch. Install the new power window switch, tighten the screws, and reconnect the connector. Test the window operation first to confirm the switch functions properly before reinstalling the trim panel.
8
2
Share

How to remove the fuel pump of Honda CRV?

Remove the rear seat of the Honda Fit vehicle, and use a flat-head screwdriver to pry open the cover plate of the Honda CRV fuel pump. Take off the cover plate of the Honda CRV fuel pump and unplug the connector of the Honda CRV fuel pump. Disconnect the fuel inlet pipe of the Honda Fit, then remove the entire fuel pump of the Honda CRV. Be extremely careful to avoid any open flames or sparks during the process. During installation, note that there are two very small oil drain holes on both sides of the fuel pump base, and no oil should drip from them. Since the fuel pump is immersed in gasoline for a long time, the sealing ring is prone to aging. When installing the fuel pump, check whether the sealing rings on the inlet and outlet pipes are aged or worn.
2
1
Share

How to Replace the Wiper Switch Assembly on a Buick Excelle?

During disassembly, first push the wiper towards the base of the wiper arm. Once it is completely detached from the wiper arm interface, pull it out in the opposite direction. Before pulling it out, rotate the movable wiper blade slightly; otherwise, it may encounter resistance during removal. Installation follows the reverse order of disassembly. First, insert the wiper interface into the wiper arm. During this step, the wiper arm clip must pass through the wiper frame. Then, pull the U-shaped connector upwards into the U-shaped clip. If you hear a crisp "click" sound, it indicates that the installation is properly seated. After installing the new motor, it is advisable to first plug in the power connector to test whether it operates normally.
2
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.