What are Peugeot's convertible models?

1 Answers
LincolnDella
07/30/25 4:38am
Peugeot's convertible models include the imported version of the Peugeot 307, which is a compact car under the Peugeot brand. This vehicle has a wheelbase of 2708 mm, with dimensions of 4428 mm in length, 1762 mm in width, and 1580 mm in height. The 307 is a hardtop convertible sports car. Hardtop convertibles offer better sound insulation performance, but the weight of the hardtop convertible mechanism is relatively high, which can have some impact on the car's handling. This model is equipped with a 2.0-liter naturally aspirated engine across all variants, delivering 140 horsepower and a maximum torque of 200 Nm. The engine reaches its peak torque at 4000 rpm and its maximum power at 6000 rpm. It features multi-point fuel injection technology and uses an aluminum alloy cylinder head and block.
Was this review help?
6
2
Share
More Forum Discussions

What is the real fuel consumption of the 2011 Teana 2.0?

The real fuel consumption of the 2011 Teana 2.0 is 8.3 liters per 100 kilometers. The fuel consumption per 100 kilometers refers to the fuel consumption of a vehicle traveling at a certain speed on the road for 100 kilometers, which is a theoretical indicator of the vehicle. The fuel consumption per 100 kilometers is a value measured by the manufacturer in an objective environment using a dynamometer installed on the vehicle chassis, converted into speed parameters, and then calculated by specifying the speed to obtain the theoretical experimental fuel consumption data per 100 kilometers for the model. The 2011 Teana 2.0 is a mid-size sedan under the Nissan brand. The corners of the headlights are exceptionally sharp, and the arc of the integrated body bumper rises from both sides to the outer edge of the headlights, then naturally extends from the outermost edge of the headlights to form a smooth waistline running from the front to the rear, complemented by a rounded arc roof, making it natural, smooth, dynamic, and stylish.
8
1
Share

Can a 48V motor be used with a 72V battery?

It cannot be used with a 72V battery because the voltage is too high and will burn out the motor. Here is an introduction about motors: "1. Introduction: A motor (English: Electric-machinery, commonly known as 'motor') refers to an electromagnetic device that realizes the conversion or transmission of electrical energy according to the law of electromagnetic induction. In a circuit, the motor is represented by the letter M (old standard uses D), and its main function is to generate driving torque as a power source for electrical appliances or various machinery. A generator is represented by the letter G in a circuit, and its main function is to convert mechanical energy into electrical energy. 2. Protector: The function of a motor protector is to provide comprehensive protection for the motor. It is a device that gives an alarm or protection when the motor experiences overload, phase loss, locked rotor, short circuit, overvoltage, undervoltage, leakage, three-phase imbalance, overheating, bearing wear, or stator-rotor eccentricity."
20
1
Share

What is the diameter of an 825r20 tire in centimeters?

20 inches. Below is an introduction about tires: 1. Introduction: A tire is a circular elastic rubber product assembled on various vehicles or machinery to roll on the ground. It is usually mounted on a metal rim, supporting the vehicle body, cushioning external impacts, achieving contact with the road surface, and ensuring the vehicle's driving performance. 2. Performance: Tires are often used under complex and harsh conditions, enduring various deformations, loads, forces, and high and low temperatures during operation. Therefore, they must have high load-bearing performance, traction performance, and cushioning performance. At the same time, they are also required to have high wear resistance and flex resistance, as well as low rolling resistance and heat generation.
17
0
Share

What is the wading depth of the xrv?

xrv has a wading depth of 25cm. When wading, pay attention to the following: 1. It is best to turn off the air conditioning: Turning on the air conditioning will cause the electronic fan at the front of the vehicle to run continuously. During wading, the rotating fan blades may stir up water, potentially causing water to enter the engine. Therefore, it is advisable to turn off the air conditioning while wading and wait for the electronic fan to stop before entering the wading section, which is better for the vehicle. 2. Accelerate appropriately when encountering oncoming traffic while wading: If there is oncoming traffic while wading, be sure to observe the height of the water waves in front of the other vehicle. If the waves are too high, you should accelerate appropriately.
5
4
Share

Are the car doors replaced at 4S stores original factory parts?

The car doors replaced at 4S stores are original factory parts, as many 4S stores do not allow the use of sub-factory components for vehicle repairs. It is not recommended to use sub-factory parts when replacing doors, as sub-factory parts differ from the original stamping molds in terms of precision and are relatively cheaper. The processing precision and manufacturing materials of original factory doors are the same as those of the original parts, and their quality meets automotive manufacturing standards. The only difference lies in the painting process: original factory doors are painted along with the entire vehicle, while replacement original factory doors are unpainted and are painted separately later. As long as the installation process is professional, there will be no significant difference in quality and completeness between original factory and original parts. Note that since car doors are not considered wear-and-tear parts, any replacement is a strong reason to suspect that the vehicle has been involved in a collision accident, which could classify the car as an accident vehicle and lead to depreciation. Therefore, it is advisable to avoid replacing the door if it is damaged in an accident, unless absolutely necessary. If safe and reliable, dent repair should be prioritized over replacement.
16
1
Share

What are the specifications of Grade 80 chain?

Here is an introduction to Grade 80 lifting chains: 1. Introduction: Grade 80 lifting chains are essential lifting devices for heavy object hoisting. They are produced using Germany's advanced assembly line equipment and high-quality alloy steel materials (such as manganese steel), with strict quality control throughout the entire process to ensure the chains meet the international Grade 80 standard. 2. Related standards: Lifting chain surface treatments: polishing, blackening, painting, plastic coating, and electroplating. Lifting chain manufacturing standards: ISO3077, EN818-2, AS2321. Lifting chain safety assurance: 4 times safety factor, 4 times test load.
17
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.