Under what circumstances does the right exhaust of the BMW X5 open?

1 Answers
OElisa
07/28/25 5:13pm
The right exhaust of the BMW X5 automatically opens when the engine speed is high. Function of the exhaust system: It mainly ensures that the water and exhaust gases produced after fuel combustion can be discharged, providing favorable conditions for the next combustion. The BMW X5's exhaust system uses a variable valve, so when the engine speed is relatively low, the valve closes, allowing the airflow to pass through a smaller pipe diameter and be discharged through a single pipe. Introduction to the exhaust pipe valve: The car's exhaust system cannot blindly pursue smoothness because backpressure is related to the engine's low-speed torque, which is the torque range most commonly used in daily driving. Therefore, the exhaust system must have corresponding devices to ensure backpressure at low speeds, and this is where the backpressure muffler comes into play.
Was this review help?
7
5
Share
More Forum Discussions

When will the China VI standard be implemented?

The China VI standard has been officially implemented since July 1, 2020. Here is relevant information about the China VI standard: 1. The China VI standard has been implemented since July 1, 2020. The China VI standard officially replaces the China V standard, but before July 1, 2025, the "in-use compliance inspection" for Phase 5 light-duty vehicles will still follow the relevant requirements of GB-18352.5-2013. 2. Compared to the currently nationwide unified "China V" standard, the China VI emission standard is more stringent, significantly reducing vehicle pollutant emissions. Taking light-duty vehicles as an example, carbon monoxide, total hydrocarbons, and non-methane hydrocarbons are reduced by 50%, and nitrogen oxides are reduced by 42%, making it more environmentally friendly.
5
0
Share

What Happens When a Car Igniter Fails?

When a car igniter fails, it can lead to difficulties in starting the car and unstable idle speed during startup. The igniter is a device capable of providing sufficient energy in an instant to ignite coal dust or oil fuel and stabilize the flame. It is a system in the vehicle that starts the engine, functioning to connect or disconnect the primary circuit of the ignition system based on the ignition signals input from the signal generator, thereby generating the ignition high voltage in the secondary winding of the ignition coil. The car igniter mainly consists of the power source, ignition coil, distributor, ignition switch, spark plug, additional resistor and its short-circuiting device, as well as high and low voltage wires.
14
5
Share

What is the pulling force of a 9500-pound winch?

9500-pound winch pulling force is 43091N. The following is a related introduction about winches: 1. Introduction: A winch is a mechanical device with a vertically mounted drum that can wind but not store ropes under power drive. It also refers to a windlass with a rotation axis perpendicular to the deck. It serves as a self-protection and traction device for vehicles and boats, enabling self-rescue and rescue operations in harsh environments such as snow, swamps, deserts, beaches, and muddy mountain roads. Under other conditions, it can be used for clearing obstacles, towing items, and installing facilities. It is an indispensable safety device for military and police, petroleum, hydrology, environmental protection, forestry, transportation, public security, border defense, firefighting, and other outdoor activities. It is mainly used for off-road vehicles, agricultural vehicles, ATV all-terrain vehicles, yachts, fire rescue vehicles, road wreckers, and other specialized and special vehicles. 2. Principle: The internal working mechanism of a winch is as follows: The electricity from the vehicle first drives the motor, which then drives the drum to rotate. The drum drives the main shaft, which in turn drives the planetary gears, generating powerful torque. The torque is then transmitted back to the drum, which drives the winch. There is a clutch between the motor and the reducer that can be switched on and off via a handle. The braking unit is inside the drum, which automatically locks when the cable is tightened.
17
5
Share

How to Maximize Fuel Efficiency in Manual Transmission Cars?

There are several methods to improve fuel efficiency in manual transmission cars: 1. Start gently by lightly pressing the accelerator and shifting up quickly. 2. Decelerate early to avoid sudden acceleration and hard braking. 3. Use appropriate gears: Match the gear to the vehicle's RPM and speed. 4. Avoid coasting in neutral, as it not only wastes fuel but is also unsafe. 5. Coordinate the clutch and accelerator when starting: Ensure a smooth start to prevent stalling and fuel wastage. 6. Minimize braking while driving: Avoid frequent braking to slow down by staying aware of road conditions and maintaining a safe distance from the vehicle ahead. When needing to stop for a red light or other situations, use low-frequency braking to coast slowly, avoiding rapid and frequent braking. This approach saves fuel while ensuring driving safety.
12
5
Share

Can You Change Lanes in a Variable Lane?

Variable lanes allow lane changes. Definition of Variable Lanes: Variable lanes are primarily set up for sections where traffic is concentrated during peak hours but has fewer lanes, or where there is a significant difference in traffic flow between morning and evening peak hours. These lanes can change the direction of travel. Purpose of Variable Lanes: The purpose of setting up variable lanes is to address the vehicle flow at intersections severely affected by tidal phenomena. In simpler terms, during morning peak hours at an intersection, the flow of straight-moving traffic is heavier, while during evening peak hours, the flow of left-turning traffic is heavier. This difference in traffic flow between morning and evening peak hours is known as the tidal phenomenon.
4
5
Share

Should You Press the Clutch or Brake First When Starting on a Slope?

When starting on a slope, press the clutch first. Below is a related introduction to starting on a slope: Concept: Starting on a slope is a field test in the second subject of the driver's license examination, which involves starting a vehicle parked on a steep slope. After positioning the vehicle correctly, pull the handbrake firmly and then pull it two more times to ensure it is tightly secured. Technique: Shift to first gear, release the handbrake, gently release the clutch, and once the vehicle is stable, proceed up the slope. Try to stay within 30 centimeters of the edge line and control the clutch as much as possible to keep the vehicle speed as slow as possible. For precise parking, use reference points aligned with the markers to ensure the front of the vehicle is aligned with the marker, thus achieving accurate positioning.
14
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.