The Harm of Rain Repellent to Glass?

2 Answers
McTanner
07/28/25 11:59pm
No harm. Here is the relevant introduction: The function of rain repellent is to form a nano-film on the glass, which has specific water-repellent properties and can effectively prevent the formation of a water film that causes blurred vision. Generally, there are no side effects. Rain repellent has the following advantages: 1. Protective performance: It not only provides 100% anti-fog effect on car glass but also prevents aging and oxidation. 2. Environmental performance: Its material is an eco-friendly product, non-toxic, odorless, non-corrosive, and highly concentrated, requiring only 2 milliliters per square meter. 3. Cleaning performance: It can clean stains on the glass surface, making the glass more transparent and brighter. 4. Anti-freezing performance: It can significantly lower the freezing point of liquids, thereby providing an anti-freezing effect and quickly dissolving frost.
Was this review help?
17
5
Share
OJoseph
08/12/25 4:16am
As someone who frequently deals with car detailing, I'd like to discuss the potential drawbacks of rain repellents. While they allow rainwater to slide off quickly, if the product contains impure ingredients or is improperly applied, the glass surface may become corroded, developing fine scratches or a hazy layer that affects nighttime visibility. Over time, the glass's transparency diminishes, and wiper operation may leave annoying streaks. What concerns me more is that some cheap rain repellents contain acidic substances that can erode the glass's outer protective coating, especially accelerating aging under high temperatures or intense sunlight. I recommend regularly cleaning the glass and choosing high-quality products, such as silicone- or fluorine-based rain repellents, to minimize these risks.
Was this review help?
8
5
Share
Expand All
More Forum Discussions

How to Check if the Windshield Washer Fluid is Sufficient?

Check if the windshield washer fluid is sufficient by following these methods: 1. If the windshield washer fluid is low, a warning light will appear on the car's dashboard. 2. During normal use, if no washer fluid sprays when using the wipers, it indicates the fluid is low. If there is no warning light, you can open the engine hood to check. Relevant information is as follows: 1. Automotive windshield washer fluid is mainly composed of water, alcohol, ethylene glycol, corrosion inhibitors, and various surface-active agents. Note that if the car lacks windshield washer fluid, tap water should not be used as a substitute. 2. Windshield washer fluid serves a cleaning function. Its surface-active agents have cleaning and penetrating effects. Long-term use can improve the transparency of the glass and maintain its cleanliness.
11
2
Share

How to Fix a Door Check Strap with No Resistance?

If the door check strap has no resistance, it is recommended to go to a repair shop for replacement as soon as possible. Here is some information about the door check strap: 1. The main function of the door check strap is to limit the degree to which the door opens. On one hand, it can limit the maximum opening of the door to prevent accidents caused by the door opening too wide; on the other hand, it can keep the door in an open state, so even on uphill roads or in windy conditions, the door will not close automatically. 2. The door check strap mainly consists of an installation bracket, a limiting arm, a limiting box, and a rubber buffer block. The installation bracket and the limiting arm are riveted and can rotate smoothly and freely.
13
0
Share

Are Rearview Mirrors Convex or Concave?

Rearview mirrors are convex mirrors. A rearview mirror is a tool that allows the driver, while seated in the driver's seat, to directly obtain external information about the rear, sides, and lower areas of the vehicle. For the convenience of the driver, to prevent traffic safety accidents, and to ensure personal safety, it is mandatory for vehicles to be equipped with rearview mirrors, and all rearview mirrors must be adjustable in direction. The installation positions of rearview mirrors are as follows: 1. The interior rearview mirror is designed to allow the driver to confirm the rear view without significantly altering the forward line of sight while driving. 2. Exterior rearview mirrors: Passenger vehicles typically have exterior rearview mirrors installed on the doors. 3. Undercarriage mirrors: These enable the driver to see areas beyond the front and rear wheels beneath the vehicle body in the mirror directly ahead of the driver's seat. This helps in spotting people or obstacles near the wheels or beside the vehicle when reversing or starting forward, thereby avoiding injuries, damage to objects or the vehicle, and providing convenience and safety to the driver.
12
2
Share

How to Deal with Sunroof Noise While Driving?

Handling sunroof noise while driving: Check the sunroof sliding rails and add a bit of lubricating oil if necessary. Inspect the sunroof's fixation, as noise is often caused by looseness. Below are some relevant details: 1. The sunroof sealing strip, long exposed to rain or intense sunlight, is prone to aging. Rubber conditioner can temporarily restore its performance. The solution is to open the sunroof fully and spray rubber conditioner onto the sealing strip. Regular vehicle maintenance is essential. If the noise persists, try adjusting the sunroof screws to eliminate the noise. 2. After 2 to 3 months of use, clean the sunroof, focusing on removing dust and particles from the gaps. Neglecting this can damage sunroof components. Use a cloth to wipe dust off the sealing strip first, then apply grease for lubrication. 3. Even if the car is parked and unused for a long time, regular cleaning is necessary. Use fine talcum powder to clean the sealing ring and other sunroof components, which can effectively extend their service life.
9
3
Share

How to remove the bumper of Honda XR-V?

The method for removing the bumper of Honda XR-V is as follows: 1. Remove the screws at the bottom of the front bumper. 2. Open the front hood and first check the installation screws of the headlights, then remove the two headlight screws. 3. Remove several screws on the frame to safely take off the bumper. Below is more information about car bumpers: 1. The car bumper is a safety device designed to absorb and mitigate external impacts, protecting the front and rear parts of the vehicle. Generally, a plastic car bumper consists of three parts: the outer panel, cushioning material, and crossbeam. The outer panel and cushioning material are made of plastic, while the crossbeam is formed by stamping cold-rolled thin plates into a U-shaped channel; the outer panel and cushioning material are attached to the crossbeam. 2. The car bumper (anti-collision beam) is located in most areas of the front and rear of the vehicle. It is designed to prevent damage to the vehicle's safety system caused by external impacts and has the ability to reduce injuries to passengers in high-speed collisions.
5
0
Share

What is Electronic Stability Control System?

Automotive Electronic Stability Control System is a new type of active safety system for vehicles. It is an extension of the functions of the Anti-lock Braking System (ABS) and Traction Control System (TCS). On this basis, it adds a yaw rate sensor, lateral acceleration sensor, and steering wheel angle sensor when the vehicle is turning. The ECU controls the driving and braking forces of the front, rear, left, and right wheels to ensure the lateral stability of the vehicle during driving. The following is a detailed explanation of the Electronic Stability Control System: 1. The system consists of three main components: sensors, an Electronic Control Unit (ECU), and actuators. The ECU monitors the vehicle's operating status and intervenes in the control of the vehicle's engine and braking system. 2. A typical automotive Electronic Stability Control System mainly includes four wheel speed sensors, a steering wheel angle sensor, a lateral acceleration sensor, a yaw rate sensor, and a brake master cylinder pressure sensor in the sensor part. The actuator part includes the traditional braking system (vacuum booster, pipelines, and brakes) and hydraulic regulators. The Electronic Control Unit works in conjunction with the engine management system, allowing intervention and adjustment of the engine's power output.
15
4
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.