Starting and Parking Sequence for the Tiguan L?

1 Answers
LeCorey
07/29/25 8:22pm
The Tiguan L is equipped with an electronic parking brake, which only requires pressing the electronic parking brake button during starting and parking. A detailed introduction to the starting and parking sequence for the Tiguan L is as follows: 1. Starting the Tiguan L: Turn on the ignition without starting the engine (wait for the self-check to complete), shift to N gear, start the ignition, and release the electronic parking brake. When starting the Tiguan L, first turn the ignition key to the second position (power mode) to allow the car's computer system to begin self-checking for at least 6 seconds. Then, press the foot brake, shift the gear from P to N, release the foot brake, turn the ignition key to the starting position to ignite the engine, press the foot brake again, release the handbrake, shift the gear from N to D, and slowly release the foot brake to successfully start the car. 2. Parking the Tiguan L: Shift the car to N gear, wait until the car is completely stationary, engage the electronic parking brake, turn off the engine in N gear, and finally shift to P gear. To park the Tiguan L, first press the foot brake to stop the car, then shift the gear from D to N, engage the handbrake, turn off the engine, release the foot brake (but do not turn off the power), confirm that the car is completely stationary under the handbrake's effect, press the foot brake again, shift the gear from N to P, finally release the foot brake, turn back the key, turn off the power, and pull out the key to successfully park the car.
Was this review help?
5
1
Share
More Forum Discussions

What to Do If Vehicle License or Driver's License Is Lost?

If the motor vehicle license is lost, the owner of the motor vehicle should apply for a replacement at the vehicle management office of the registration location. The required materials for the application are as follows: 1. Application form: 'Motor Vehicle License Plate and Certificate Application Form'. 2. ID: Original and photocopy of the owner's identity proof. 3. Lost part: For replacement or reissuance of license plates or vehicle licenses, the undamaged, lost, or damaged parts must be returned. 4. Proxy proof: If an agent handles the application, a power of attorney and the agent's identity proof must also be submitted. 5. Other proofs: Other proofs and certificates required by laws and administrative regulations when applying for replacement registration certificates, replacement or reissuance of license plates, or vehicle licenses.
14
3
Share

Why Does the BMW N20 Engine's High-Pressure Fuel Pump Make Noise When Starting?

BMW N20 engine's high-pressure fuel pump making noise when starting is mainly caused by overfilling the fuel tank, insufficient fuel storage, or fuel pump damage. Overfilling the Fuel Tank: When refueling the car, it is advisable not to fill the tank completely at once, as this may cause the fuel float and sensor to malfunction, distort the fuel gauge, and increase fuel consumption. It is recommended to refuel when the fuel level is low. Insufficient Fuel Storage: When refueling the car, do not wait until the fuel warning light comes on. Having too little fuel or running out of fuel may burn out the fuel pump and reduce its service life. Fuel Pump Damage: Improper refueling behavior may damage the high-pressure fuel pump.
4
1
Share

What is a car DSP?

The following is relevant information about DSP amplifiers: 1. Introduction to DSP amplifiers: A DSP amplifier refers to an amplifier that utilizes a DSP chip to optimize and manage audio parameters through digital signal processing algorithms. It is a technology that converts two-channel stereo signals into multi-channel surround sound signals. 2. Characteristics of DSP amplifiers: Can complete one multiplication and one addition within a single instruction cycle; separates program and data spaces, allowing simultaneous access to instructions and data; contains fast RAM on-chip, typically accessible via independent data buses in two blocks simultaneously; provides hardware support for low-overhead or no-overhead loops and jumps; offers fast interrupt handling and hardware I/O support; features multiple hardware address generators that operate within a single cycle; enables parallel execution of multiple operations; supports pipeline operations, allowing overlapping execution of operations such as fetching, decoding, and executing.
3
0
Share

How to Start the Audi A3?

The method to start the Audi A3 is as follows: 1. Press the clutch pedal all the way down; 2. Push the gear lever to engage the 1st gear; 3. Gently press the turn signal lever downward to activate the left turn signal, alerting vehicles in front and behind; 4. Press the horn button to alert pedestrians in front of the vehicle that you are about to start; 5. Release the vehicle's handbrake; 6. Lift the left foot slowly until the clutch reaches the half-clutch position, and the vehicle begins to vibrate slightly; 7. As the vehicle starts to move, release the clutch and gently press the accelerator. Taking the 2021 Audi A3 as an example, it is equipped with a 1.4L naturally aspirated engine, delivering a maximum horsepower of 150 PS, a maximum power of 110 kW, and a maximum torque of 150 Nm, paired with a 7-speed dual-clutch transmission.
15
0
Share

What Causes Newly Replaced Brake Pads to Overheat and Emit a Burning Smell?

Newly replaced brake pads overheating and emitting a burning smell are typically caused by insufficient clearance between the brake pads and brake discs or a stuck brake caliper. Below are some precautions for brake pad usage: 1. Service Life: Under normal driving conditions, the lifespan of front brake pads is generally 30,000–50,000 kilometers, while rear brake pads last 120,000–150,000 kilometers. The replacement interval should be determined based on actual wear. Different vehicle models may have varying manufacturer-recommended mileage. 2. Replacement: When replacing brake pads, always choose products from reputable manufacturers. Genuine manufacturers' brake pads usually feature clear packaging with information such as license numbers, specified friction coefficients, and compliance standards. The packaging should also include a certificate of conformity, production batch number, and manufacturing date. It is advisable to have new brake pads installed by professionals at certified repair shops to avoid errors that could lead to potential safety hazards. 3. Inspection: During brake pad inspections, it is also essential to examine the wear on brake discs or drums to ensure sufficient contact area with the pads for optimal braking performance.
12
2
Share

What is the engine displacement of the Bugatti Veyron?

The engine displacement of the Bugatti Veyron is 8 liters. Parameters of the Bugatti Veyron engine: 8.0-liter W16 cylinder with 4 turbochargers, 1200 horsepower and 1250 Nm of torque, capable of accelerating from 0 to 100 km/h in 2.5 seconds; to 200 km/h in 7.3 seconds; and reaching 300 km/h in 16.7 seconds. Introduction to the Bugatti Veyron engine: It uses a W16 engine, where 'W' represents the arrangement of the engine cylinders. The W-type configuration allows the engine to be made shorter, with a shorter crankshaft, thus saving space occupied by the engine. This results in a lower vehicle height and a superior drag coefficient. Additionally, the weight is reduced, but the width is increased, making the engine compartment more compact.
11
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.