Solutions for Oil Burning in the Tiguan

1 Answers
GenesisFitz
07/29/25 4:15pm
Tiguan oil burning requires cleaning the oil filter. Early prevention can be achieved through the following measures: 1. Use high-quality engine oil. Engine oil is highly susceptible to corrosion and aging under prolonged high temperatures, causing the oil film to thin and more likely to enter the combustion chamber to participate in combustion. Therefore, using high-quality engine oil can significantly delay this phenomenon. 2. Pay attention to the cleanliness of the fuel system. Fuel combustion produces carbon deposits, which are the root cause of some car problems, such as aging of the valve oil seal and increased piston cylinder wall clearance. These issues are directly or indirectly related to carbon deposits. Therefore, maintaining the cleanliness of the fuel system is very helpful in preventing oil burning, and this can be achieved with the help of high-quality fuel additives.
Was this review help?
10
1
Share
More Forum Discussions

How to Remove the Battery from a Passat?

After parking the car, engage the handbrake. Open the hood and locate the battery, which is generally positioned on the driver's side within the engine compartment. On the outer casing, there are clear positive and negative terminal markings, usually color-coded with the red terminal as the 【+】 positive and the black terminal as the 【-】 negative. Use a wrench to loosen the terminal nuts, starting with the 【-】 negative terminal. Avoid contact with metal during the removal process. Following the previous step, carefully remove the 【+】 positive terminal. After removing both terminals, there is usually a frame securing the battery in place. Release the securing rod to remove the battery.
18
2
Share

What is the simple solution for exhaust pipe gasket leakage?

You can first try replacing the gasket, as the leakage may be caused by gasket aging. During repair, you can use the method of wrapping copper wire around the joint. Cut a section of copper wire from an old cable and wrap it tightly around the gasket in loops, one loop tightly after another.
14
1
Share

What Causes the Engine Malfunction Light to Illuminate and the Vehicle to Fail to Start?

Engine malfunction light illumination and failure to start can be caused by: 1. Poor quality or substandard gasoline; 2. Oxygen sensor failure; 3. Air flow sensor malfunction; 4. Spark plug carbon buildup; 5. Engine knocking; 6. Coolant temperature sensor damage; 7. Engine misfiring. Solutions for engine malfunction light illumination and failure to start include: 1. Switching to higher-octane gasoline; 2. Replacing the oxygen sensor; 3. Replacing the air flow sensor; 4. Cleaning the spark plugs; 5. Replacing the engine; 6. Replacing the coolant temperature sensor. To reset the engine malfunction light: Turn the vehicle on and off three times consecutively.
18
4
Share

What Causes the Squeaking Sound When Braking in a New Car?

The reasons for the squeaking sound when braking in a new car are: 1. Rust on the brake pads during storage; 2. New brake pads not yet worn in; 3. Improper installation of brake pads during assembly; 4. Use of low-quality or overly hard brake pads; 5. Presence of sand or foreign objects between the brake pads and brake discs. Precautions when braking include: 1. Release the brake once before the vehicle comes to a complete stop, then gently apply the brake until the vehicle stops moving; 2. Reduce speed adequately by braking before entering a curve; 3. Pay attention to controlling speed in rainy conditions, use emergency brakes cautiously to avoid skidding and rollover due to slippery roads.
1
1
Share

How to Bleed Car Brakes?

The method for bleeding car brakes is: 1. Locate the bleeder screw on the brake caliper and remove the dust cap from the bleeder valve; 2. Connect the bleeder port to a drain bottle using a rubber tube; 3. Depress the brake pedal and loosen the bleeder screw on the brake caliper, repeating this operation as needed. The brake is located below the driver's seat and the console. Braking, also known as stopping, refers to the action of halting or reducing the speed of moving locomotives, vehicles, other transportation tools, or machinery. The working principle of brakes is: a wheel or disc is fixed on the high-speed shaft of the machine, and a corresponding brake shoe, band, or disc is installed on the machine base to generate braking torque under external force.
7
1
Share

What is the Chinese meaning of 'scan'?

The Chinese meaning of 'scan' is to search or scan, referring to the function of searching for radio stations and stopping once a station is found, which is commonly displayed on the electronic screens in cars. When this button is pressed in CD playback mode, the display will show the word 'scan', and the music will start scanning from the next track of the currently playing song, playing each track for a few seconds before moving to the next one in a loop. When the user hears a track they like, pressing this button again will make the player start playing from that track. Other car function introductions: 1. VOL volume adjustment; 2. MUTE mute; 3. MODE selection: such as choosing the audio source between CD, MP3 from a USB drive, or radio; 4. RDM random playback.
3
3
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.