Should You Turn Off the Engine Before Shifting to P Gear or Shift to P Gear Before Turning Off the Engine?

1 Answers
Lola
07/28/25 10:29pm
It is best to turn off the engine before shifting to P gear. Engine shutdown method: Normally, when parking the car, first bring the car to a complete stop, then shift the gear to N gear, engage the handbrake, turn off the engine, and then shift to P gear. This is the correct way to turn off the engine. The correct steps for starting an automatic transmission car are: Press the brake, engage the handbrake, start the engine (do not directly shift to D gear; shift to N gear first and then start the engine, then shift from N gear to D gear), release the handbrake, release the foot brake, and release the handbrake (for electronic handbrakes, simply press the button briefly). You can choose to warm up the car in place, and the time can be determined based on the environment. Press the accelerator and start moving. Depending on the road conditions, press the accelerator smoothly to accelerate and drive safely.
Was this review help?
13
2
Share
More Forum Discussions

What to Do When Brakes Fail While Driving?

Emergency measures for brake failure while driving are as follows: 1. Develop the good habit of lightly tapping the brake when going downhill during normal driving to test if the brakes are functioning. If the speed is not too fast, try using the handbrake first to see if it can reduce the speed. When pulling the handbrake, be sure not to pull it too quickly or too firmly. If the handbrake is pulled too hard, the steel cable may snap due to the speed and inertia. 2. If the handbrake doesn't work, try downshifting to see if you can shift from a higher gear to a lower one. 3. Carefully observe the road conditions to see if there are any hillsides on either side to rely on. If there are, it's best to approach the hillside on the right (as the right side is relatively less harmful to you and can protect you to the greatest extent). Slowly steer the car toward the roadside, firmly grip the steering wheel with both hands, and gently scrape against the hillside.
1
2
Share

How to use the cruise control on the Geely Emgrand?

Geely Emgrand cruise control usage method: 1. Activate cruise control: Press the control switch to activate cruise control standby. 2. Set cruise speed: After accelerating, push the control lever downward to set the cruise speed. 3. Cancel cruise control: You can lift the control lever upward, turn off the main cruise control switch, press the accelerator pedal, or lightly tap the brake. More information about the Geely Emgrand is as follows: 1. Geely Emgrand (referred to as Emgrand) is a sub-brand built under the Geely parent brand. 2. The Geely Emgrand is equipped with a 1.3T GeTec DVVT turbocharged engine, with a maximum power of 98kw, turbo intervention at 1800 rpm, and peak torque output of 185NM at 2000 rpm.
18
0
Share

What brand is Rebel?

Rebel is a motorcycle produced by Honda Motor Company of Japan. Here is an introduction to the Rebel motorcycle: The first-generation Rebel was released in 1985. A compact body houses a 233cc air-cooled 4-stroke SOHC twin-cylinder engine, providing excellent power, handling, and impressive acceleration, which has earned it support from many female riders. In the 1986 version, dual carburetors were added to enhance performance. The fuel tank was redesigned, and decorative panels with gold accents were introduced. The 1988 version featured sport-style handlebars, replacing the traditional wide curved handlebars. This design marks the origin of the current Rebel series handlebars. The 1990 version underwent a complete redesign of the engine appearance and side covers, though the overall look remained largely unchanged. In the 1994 version, the sport-style handlebars were removed, and the traditional wide curved handlebars made a comeback. The bike exuded a heavy metal aesthetic, and the exhaust was changed to a single-sided dual-exit configuration. The 2017 version showcased a design that epitomized technological advancement, featuring large tires, a square radiator, black matte exhaust, and a muscular body. The Honda 2022 Rebel250 went on sale in Japan starting January 20, 2022. Key technical specifications are as follows: Engine Type: Single-cylinder, liquid-cooled, 4-stroke, DOHC, 4-valve; Displacement: 249mL; Bore × Stroke: 76.0mm × 55.0mm; Compression Ratio: 10.7:1; Maximum Power: 19kW (9500r/min); Maximum Torque: 22N•m (7750r/min); Wheelbase: 1490mm; Ground Clearance: 150mm; Fuel Delivery System: Electronic Fuel Injection (PGM-FI); Starting System: Electric Start; Ignition System: CDI; Clutch Type: Wet Multi-Plate; Transmission Type: 6-speed; Braking System: Front and Rear Disc Brakes; Dimensions (L × W × H): 2205mm × 820mm × 1090mm; Seat Height: 690mm; Curb Weight: Rebel250 170kg, Rebel250SEdition 171kg; Fuel Tank Capacity: 11L; Tire Specifications: (Front) 130/90-16M/C 67H, (Rear) 150/80-16M/C 71H.
18
4
Share

Is Changan Automobile Fuel-Consuming?

Changan Automobile's fuel consumption is average, and it varies depending on the car's engine. Additionally, a driver's habits significantly impact gasoline consumption. Engine displacement is one of the factors affecting fuel consumption. Common displacement fuel consumption figures are as follows: 1.0L displacement: Manual models consume around 4L per 100km, automatic models 4.5-5L; 1.5L displacement: Manual models around 5L, automatic models 6-7L; 1.6L displacement: Manual models around 5.5L, automatic models 6-7L; 1.8L displacement: Manual models around 7L, automatic models 8-9L; 2.0L displacement: Manual models 7-8L, automatic models 9-10L; 2.4L displacement: Manual models around 9L, automatic models 11-12L; 3.0L displacement: Manual models around 12L, automatic models 13-15L. Naturally, turbocharged (T) models consume relatively more fuel than naturally aspirated (non-T) ones. Due to different mechanical designs, reaching an optimal state takes time, similar to warming up before intense exercise. Rapid acceleration and braking during driving may showcase the driver's skills and car performance, but this driving style can cause fuel consumption to skyrocket, 2-3 times higher than normal driving! The optimal driving speed is preferably maintained at 60-80 km/h, with road conditions observed in advance to control speed using the throttle. Route selection, though not directly related to driving, is a crucial aspect of fuel saving. Sometimes, longer routes may not necessarily have worse conditions. Therefore, when choosing a route, opt for less congested and shorter paths to save more fuel. If the vehicle carries heavy loads, fuel consumption will be about 2% higher than normal. While this might seem insignificant, small amounts accumulate over time, making it a significant expense. Avoid keeping unnecessary items in your car that could be stored at home. Some drivers might think that in hot summer weather, tires expand and contract, making them slightly loose. This is not the case. Proper tire pressure is crucial for fuel efficiency and tire lifespan. A tire with 40 kPa less air pressure will reduce tire life by 10,000 km and increase fuel consumption by 3%. A 30% decrease in tire pressure at 40 km/h can increase fuel consumption by 5%-10%. Therefore, maintaining correct tire pressure is essential for fuel economy.
5
5
Share

What Causes Front Axle Noise in Cars?

Possible causes of front axle noise in cars include: 1. Improper adjustment of the backlash or poor meshing contact area between the driving and driven spiral bevel gears, damage to the tooth surfaces of these gears, or broken gear teeth. 2. Improper adjustment of the main reducer bearing clearance. Excessive wear of the differential planet gear washers or side gear washers, damage to the differential gears or cross shaft, excessive clearance or seizure of the wheel hub bearings, broken teeth of the wheel hub planet gears or sun gears. 3. Damage to the wheel hub ring gear and its support. Loose wheel hub retaining nuts, insufficient lubrication in the main reducer or wheel hub reducer, lack of lubrication or bearing failure in the front driveshaft intermediate support.
16
0
Share

Which Side is the Brake in an Automatic Transmission?

In automatic transmission models, the left side is the brake, and the right side is the accelerator. Precautions for automatic transmission cars are as follows: 1. The accelerator and brake in an automatic transmission car are relatively simple, with only two pedals located below the driver's seat and the console. From left to right, they are the brake pedal and the accelerator pedal, both controlled solely by the right foot. The gear shift is positioned in front of the center armrest on the right side, easily visible upon entering the car. 2. The main reason for this design is that the accelerator is used more frequently. Placing it on the outer side of the right foot provides a more comfortable posture for the driver. The brake is set on the inner side of the right foot, and the brake pedal is slightly higher than the accelerator pedal.
12
2
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.