Should You Release the Accelerator When Upshifting with Paddle Shifters?

What to Do If the Duplicate of the Driver's License Is Lost?

If the duplicate of the driver's license is lost, it is necessary to promptly apply for a replacement at the vehicle management office. The original copy records the basic information of the vehicle, while the duplicate copy records the inspection status of the vehicle. Driving is not allowed if the driver's license is lost. According to the Road Traffic Safety Law of the People's Republic of China, motor vehicle drivers are not allowed to drive if their driver's license is lost, damaged, expired, detained or temporarily confiscated by law, or if their score reaches 12 points. To apply for a replacement of the driver's license, the applicant must personally go to the vehicle management office with their original ID card and a copy. Non-local residents also need to bring their original residence permit and a copy. At the vehicle management office, fill out the motor vehicle license and certificate application form, then submit the documents and the completed form to the office staff and pay the service fee.

12

0

Share

What to Do If the Car Won't Start?

Solutions for a car that won't start are as follows: 1. Check if the fuel level is insufficient and refuel promptly. 2. Inspect the condition of the car's timing belt. 3. Replace the spark plugs. 4. Check if the engine's intake pipe is clogged or has water ingress. 5. Inspect the fuel system for any faults. Reasons why the car won't start: 1. Fuse blown, high-voltage coil open circuit, or low-voltage circuit open. 2. Central ignition coil detached. 3. Distributor rotor leaking electricity. 4. Spark plugs damaged. 5. Central computer control board damaged. 6. Fuel pump failure, fuel line blockage, fuel filter clogged, spark plug carbon buildup, or injector damage.

16

5

Share

How to set the lock beep for BMW X1?

This vehicle cannot be set because the car does not provide the lock beep function. This model supports automatic folding of the rearview mirrors when locked. After completing the lock, you can observe whether the rearview mirrors are folded to determine if the vehicle has been locked. Once locked, you can leave the vehicle. Here are some relevant details: The BMW X1 has a body length of 4565 mm, a width of 1821 mm, a height of 1620 mm, and a wheelbase of 2780 mm. It is a five-door, five-seater SUV with a fuel tank capacity of 61 liters and a trunk capacity ranging from 505 liters to 1650 liters. The vehicle is positioned as a compact SUV.

16

0

Share

What does it mean when the ABS light is on?

When the ABS light is displayed on a vehicle, it indicates a malfunction in the Anti-lock Braking System. During emergency braking, if the wheels lock up, the vehicle may lose control and skid, making it difficult for the driver to slow down or adjust the vehicle's trajectory, posing significant safety risks. There are several conditions under which the ABS light may illuminate, each with different causes and solutions, as detailed below: Condition 1: ABS warning light stays on continuously (most common). Cause 1: The ABS speed sensor's sensing area is covered by dirt, mud, or other contaminants, affecting the sensor's ability to detect the corresponding speed signal. This prevents the ABS computer from determining the vehicle's speed and the wheel's slip rate, thus failing to issue appropriate commands to adjust braking. Solution: Clean the dirt off the speed sensor and adjust the gap between the speed sensor and the signal ring to restore normal function. Cause 2: Poor signal due to loose connections in the system wiring or poor contact in the ABS relay, leading to system failure. Solution: Check the wiring connections and reconnect any loose parts. Condition 2: ABS warning light intermittently illuminates but turns off when accelerating. Cause: When multiple vehicle electrical devices are in use, the battery voltage drops below 10.5V. As the engine speed increases, the voltage rises, causing the ABS light to turn off. This may also be due to insufficient power supply voltage to the ABS system, such as poor terminal contact or grounding issues. Solution: Check the battery's specific gravity; inspect the charging system; examine the power supply (e.g., voltage relay or poor power contact). Condition 3: ABS warning light stays on after engine start and only turns off when the engine is turned off (IGFF). Cause: Poor grounding contact in the ABS hydraulic valve body; poor contact in the ABS hydraulic valve body wiring connector; ABS computer malfunction. Solution: Loosen the grounding screw on the hydraulic valve body, then retighten it, cleaning the contact surface if necessary; check if the connector gap has widened; replace the ABS or ABS/ASR computer. Condition 4: ABS warning light illuminates during high-speed driving. Cause: At high speeds, the ABS computer detects a significant discrepancy between the rear and front wheel speed signals; incorrect tire or wheel rim specifications. Solution: Refer to the vehicle's tire and wheel rim specifications, as indicated on the sticker near the fuel tank cap. Condition 5: ABS warning light intermittently illuminates. Cause: Improper adjustment of the brake light switch; poor internal contact in the brake light. Solution: With the engine running, press the brake pedal, push the brake switch linkage down fully with your finger, then release the brake pedal to complete the self-setting position; replace the brake light switch if necessary.

11

1

Share

What Causes Body Shaking When Starting in First Gear?

Body shaking when starting in first gear is generally caused by excessive wear of the clutch pressure plate. The manual transmission primarily transfers power through the clutch, and the clutch pressure plate is mainly responsible for transmitting kinetic energy. The clutch pressure plate has a service life, and prolonged operation in a semi-engaged state or excessive engine load can accelerate its wear. Below is an introduction to the clutch pressure plate: The front end of the transmission shaft is supported by a bearing in the center hole of the flywheel, while the rear end is supported by a bearing on the transmission housing. The clutch disc hub is connected to the transmission shaft via sliding splines. The pressure plate spring presses the pressure plate and clutch disc tightly against the flywheel, keeping the clutch in a normally engaged state.

18

2

Share

What Causes the Car Battery Warning Light to Illuminate?

Reasons for the car battery warning light to illuminate: 1. Battery malfunction, such as depleted charge or battery failure. Use a multimeter to check the battery voltage. If the voltage is low, recharge it; if the battery has failed, replace it. 2. Loose or oxidized battery terminals causing poor contact can also trigger the battery light. Clean and tighten the battery connections. 3. A loose generator belt or tensioner causing the charging system to malfunction will illuminate the battery light. Replace the belt or adjust the tension. 4. Faulty generator voltage regulator or excitation circuit issues causing abnormal operation will light the battery warning light. Troubleshoot the generator.

15

0

Share

Should You Release the Accelerator When Upshifting with Paddle Shifters?

What to Do If the Duplicate of the Driver's License Is Lost?

What to Do If the Car Won't Start?

How to set the lock beep for BMW X1?

What does it mean when the ABS light is on?

What Causes Body Shaking When Starting in First Gear?

What Causes the Car Battery Warning Light to Illuminate?

Where is the engine of the Venucia Star produced?

Where is the fuse box located in a BMW X5?

What to Do If You Forget to Bring Your Driver's License and Get Checked by Traffic Police?

How to Open the Hood of a Buick Excelle?