Should You Engage the Handbrake or Start the Engine First in Subject Two?

1 Answers
Gavin
07/30/25 7:28am
First press the clutch, then press the ignition switch. Here are the relevant instructions: 1. Subject Two Test: In the Subject Two test, the correct method to start is to pull up the parking brake, press the clutch pedal all the way down, confirm the gear is in neutral, press the ignition switch for 2 to 3 seconds. Shift to first gear, turn on the left turn signal, observe the left and right rearview mirrors, release the parking brake, gently press the accelerator, slowly release the clutch, and start smoothly. 2. Key Points: Master the basic driving operation essentials and have the basic ability to control the vehicle; proficiently master the basic methods of driving on the site and on the road within the site, have the ability to reasonably use vehicle control components and correctly control the spatial position of the vehicle, and be able to accurately control the vehicle's driving position, speed, and route.
Was this review help?
16
5
Share
More Forum Discussions

What to Do If the First Car Maintenance Card Is Lost?

If the first car maintenance card is lost, the solution is to contact the 4S store for a replacement. The first maintenance refers to the preventive work of regularly inspecting, cleaning, supplying, lubricating, adjusting, or replacing certain parts of the car. Its purpose is to maintain the car's appearance, ensure normal technical conditions, eliminate hidden dangers, prevent failures, slow down the deterioration process, and extend the service life. The first maintenance items include: 1. Replace engine oil, oil filter, brake fluid, clutch fluid, power steering fluid, spark plugs, transmission fluid, fuel filter, air filter, and cabin air filter; 2. Check the battery and battery water; 3. Refill windshield washer fluid; 4. Check the tension of the engine belt.
5
3
Share

What should be noted for safe driving in extremely cold weather conditions?

Here are the key points to note for safe driving in extremely cold weather conditions: 1. Pay attention to the warm-up procedure: First depress the clutch, then start the car. This allows the car to lubricate in advance, thus avoiding damage to the vehicle. 2. Always check the car's tires before driving: In winter, tires may freeze, so if such a situation is observed, clean them promptly to ensure safe driving. 3. Winter driving: It is essential to be more focused and avoid distractions, as roads in winter may inevitably have some ice and snow. 4. Avoid speeding in snowy conditions: On snowy winter days, it's best not to drive on highways and certainly avoid speeding.
6
0
Share

Is the Toyota Sienna 4WD a Full-Time Four-Wheel Drive?

Toyota Sienna 4WD is a full-time four-wheel drive, which means that at all times, the vehicle is propelled by four wheels independently. The Toyota Sienna is a 5-door, 8-seater MPV with body dimensions of 5175 mm in length, 1995 mm in width, and 1775 mm in height, a wheelbase of 3060 mm, and a fuel tank capacity of 68 liters. The Toyota Sienna is equipped with a 2.5L naturally aspirated engine, delivering a maximum power of 141 kW at 6000 rpm, paired with an electronic continuously variable transmission. The front suspension uses a MacPherson strut independent suspension, and the rear suspension employs a multi-link independent suspension.
9
5
Share

What is the fuel consumption of the new Ford Edge?

The new Ford Edge has a total of 6 models on sale, including the 2020 EcoBoost245 two-wheel-drive Enjoy version, the 2020 EcoBoost245 two-wheel-drive Shine version, and other 6 models equipped with a 248 horsepower engine. The NEDC fuel consumption per 100 kilometers is 7.3L. The fuel tank capacity of different models of the new Ford Edge varies. The distance that can be covered with a full tank of fuel is as follows: Models equipped with a 248 horsepower engine have a fuel tank capacity of 63L, and the distance that can be covered with a full tank of fuel is 63/7.3*100=863KM. The fuel consumption of a car is directly related to five major factors, namely driving habits, the car itself, road conditions, natural wind, and environmental temperature. The specific factors that increase car fuel consumption are as follows: Driving habits: Rough driving, such as sudden acceleration, frequent overtaking, and not releasing the throttle in advance when encountering a red light, will increase fuel consumption. The car itself: Cars with larger displacement consume more fuel than those with smaller displacement because larger displacement generally means greater power, requiring more gasoline to burn and do work. Cars with greater self-weight will have higher fuel consumption because greater self-weight requires larger driving torque. Road conditions: Dirt roads, muddy roads, soft roads, mountain roads, etc. Driving on these roads increases resistance and fuel consumption. Natural wind: Driving against the wind or on windy days increases car resistance and fuel consumption. Low environmental temperature: When the engine block temperature is low, the gasoline injected during cold starts is not easy to atomize, requiring more gasoline to be injected for combustion, thus increasing fuel consumption. At the same time, when the temperature is low, the engine computer will control the car to use higher RPM to warm up, which will also increase fuel consumption.
9
0
Share

What is the oil specification for the Buick Excelle?

The oil specification for the Buick Excelle is 5w30. The meanings represented in the oil specification are: 1. The number before the w indicates the low-temperature flow performance of the oil; 2. 5w means the oil can flow normally at minus 30 degrees Celsius; 3. 0w means the oil can flow normally at minus 35 degrees Celsius; 4. The number after the w indicates the high-temperature viscosity of the oil, with higher numbers representing higher viscosity. The Buick Excelle is a 4-door, 5-seater compact sedan with body dimensions of: length 4609 mm, width 1798 mm, height 1486 mm, a wheelbase of 2640 mm, and a fuel tank capacity of 44 liters.
7
1
Share

How to Deal with Corroded Car Battery Terminals?

Solutions for corroded car battery terminals include: 1. Rinsing with boiling water at 100 degrees Celsius; 2. After cleaning off the corrosion, apply petroleum jelly. A car battery, also known as a storage battery, is a type of battery categorized into standard batteries, dry-charged batteries, and maintenance-free batteries. Its working principle involves converting chemical energy into electrical energy. Methods for maintaining a car battery include: 1. Regularly clean the dust and grease from the battery terminals and apply specialized grease to protect the wiring harness; 2. Periodically inspect the battery's components and connecting circuits; 3. Minimize the use of in-car electrical devices after turning off the engine; 4. Check the battery through the inspection window and replace it periodically; 5. Start the car regularly if it is not used for an extended period.
15
0
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.