Should Turn Signals Be Used When Exiting the Garage in Subject 2?

1 Answers
MaddoxLee
07/29/25 4:36pm
When performing reverse parking or exiting the garage in Subject 2 of the driving test, turn signals are not required. There are a total of 6 instances in Subject 2 where turn signals must be used, which are: 1. Turn on the left turn signal when starting the vehicle; 2. Turn on the left turn signal when starting on a slope; 3. Use the right turn signal when passing the parallel parking spot and preparing to park within 30 cm of the side line before reversing; 4. Turn on the left turn signal before shifting into reverse gear during parallel parking, as the steering wheel will be turned fully to the right, causing the front of the car to shift left during reversing; 5. Shift into drive gear and turn on the left turn signal before exiting the parallel parking spot, and turn it off promptly after exiting; 6. Turn on the left turn signal when entering the sharp turn area and turn it off promptly after completing the turn. Penalties for incorrect use of turn signals are as follows: - Failing to use or incorrectly using turn signals before starting, turning, changing lanes, overtaking, or parking results in a deduction of 10 points. - Turning the steering wheel within less than 3 seconds of activating the turn signal before starting, turning, changing lanes, overtaking, or parking results in a deduction of 10 points. Subject 2 has a total score of 100 points, with evaluation criteria for failing, deducting 20 points, deducting 10 points, or deducting 5 points. The test is considered passed under the following conditions: ① For large passenger vehicles, tractors, city buses, medium passenger vehicles, and large trucks, a score of 90 or above is required; ② For other vehicle types, a score of 80 or above is required. The test items for small vehicles (C1, C2) include reverse parking, parallel parking, slope parking and starting (canceled for C2), sharp turns, and S-curves (commonly known as the "S-bend")—five mandatory items (some regions include a sixth item: highway toll card collection). The test items for large vehicles (A1, A2, A3, B1, B2) include pole parking, slope parking and starting, parallel parking, single-plank bridge crossing, S-curves, sharp turns, narrow gate passing, continuous obstacle passing, bumpy road driving, narrow road U-turns, as well as simulated highway driving, continuous sharp mountain turns, tunnels, rain (fog) conditions, slippery roads, and emergency handling.
Was this review help?
13
2
Share
More Forum Discussions

What Causes Valve Noise?

Valve noise is caused by: 1. Gap formation or severe wear in hydraulic lifters; 2. Too high or too low oil level in the crankcase; 3. Dirty lifters; 4. Worn valve spring seats with grooves, and wear between valve stems and guides; 5. Oil being too thin—replace with oil of appropriate viscosity; 6. Oil pressure being too low or too high. The methods to address valve noise are: 1. Remove the cylinder head; 2. Grind the valves, check the spring tension of the valve springs, and readjust the valve clearance. The function of valves is to specifically input air into the engine and expel exhaust gases after combustion. Based on engine structure, they are divided into: intake valves and exhaust valves.
20
3
Share

How to Drive an Automatic Transmission Car Down a Long Slope?

To drive an automatic transmission car down a long slope, follow these steps: 1. Brake and slow down in advance at the top of the slope; 2. Shift into L mode to assist with braking and control speed throughout the descent; 3. Upon reaching the bottom of the slope, shift back to D mode and accelerate directly. The gears of an automatic transmission car are: 1. P gear is the parking gear and starting gear; 2. R gear is the reverse gear; 3. N gear is the neutral gear; 4. D gear is the forward gear, also known as the drive gear; 5. S gear is the sport mode; 6. L gear is the low-speed gear. The characteristics of an automatic transmission are: it uses planetary gear mechanisms for shifting, automatically adjusting based on the degree of the accelerator pedal and changes in speed, allowing the driver to control the speed simply by operating the accelerator pedal.
12
1
Share

How many liters of coolant are needed for a BMW replacement?

BMW requires 6.5 liters of coolant for a single replacement. Coolant is a special additive-containing liquid primarily used in liquid-cooled engine cooling systems. It offers excellent performance features such as preventing freezing in winter, boiling in summer, and inhibiting scale and corrosion year-round. Can different coolants be mixed? Only use the same brand of coolant. Different brands may have varying production formulas, and mixing them could trigger chemical reactions between additives, rendering them ineffective. How to check for low coolant levels: Monitor the coolant warning light on the dashboard. If illuminated, it likely indicates low coolant, though it could also signal excessively high cylinder temperatures. Inspect the coolant reservoir. If the level falls below the minimum mark (MIN), do not continue driving and promptly add coolant. Check the level indicators on the coolant overflow tank. Normal coolant levels should be between the MAX and MIN marks. If the level drops below MIN, it indicates insufficient coolant.
18
3
Share

Why Does the Chassis Make a Rattling Noise on Rough Roads?

This issue is mostly caused by the aging of rubber components in the chassis. Rubber parts in the chassis effectively absorb vibrations generated by the suspension during operation. Therefore, if these rubber components are damaged or aged, the vibrations cannot be mitigated, and the noise from the suspension will directly transmit into the cabin, giving the impression of a very loose chassis. During regular maintenance, it's advisable to check the condition of the chassis rubber components. If any cracks are found, they should be replaced as soon as possible. Here are some methods to restore a loose chassis in older vehicles: 1. Replace the shock absorbers. In older vehicles, the lubricating oil inside the shock absorbers is likely depleted, significantly affecting their rebound and compression functions. Replacing the shock absorbers can effectively improve the driving experience. 2. Replace the lower control arm. The ball joint of the lower control arm is the most prone to wear. When the ball joint lacks lubrication for an extended period, the wear becomes severe, leading to excessive play in the lower control arm. 3. Replace the rubber bushings. There are many vibration-damping rubber bushings in the vehicle chassis. If these bushings age or crack, various abnormal noises from the chassis will occur during driving.
10
4
Share

What are the differences between China-spec and US-spec vehicles?

1. Different target markets: China-spec vehicles: Vehicles sold to the Chinese market are called China-spec. US-spec vehicles: Vehicles sold to the US market that comply with US traffic regulations are called US-spec. 2. Different language displays: China-spec vehicles: The dashboard and central control display show information in Chinese. US-spec vehicles: US-spec vehicles display information in English, though many agencies in China offer services to convert the display from English to Chinese. 3. Differences in after-sales service and maintenance: US-spec vehicles: There is a yellow reflective strip on the side of the headlights, which is a mandatory requirement for all vehicles in the US. The engine's power output curve may also be adjusted. China-spec vehicles: China-spec vehicles do not have this reflective strip on the side of the headlights. China-spec models are specially tuned to better suit Chinese road conditions and fuel quality, mainly in terms of the chassis suspension system.
17
4
Share

What Causes a Motorcycle to Frequently Stall While Riding?

Here are the reasons why a motorcycle frequently stalls while riding: 1. Fuel supply system: The first component to check for this issue is the carburetor, although often the problem is not directly related to it. 2. Ignition system: Poor contact in the ignition system or damage to ignition components can cause irregular stalling during operation. 3. Mechanical failure: Aging valves, excessively tight valve clearances, or excessive wear on the camshaft can lead to frequent stalling while the motorcycle is in motion. Additional information: 1. When troubleshooting this issue, diagnosis should be based on the symptoms. Generally, the ignition system is more likely to be the culprit, with the trigger coil and poor contact being the most common causes. Therefore, the focus should be on inspecting the ignition system. 2. First, check the wiring connections. If unsure, replace the trigger coil without hesitation—this resolves over 80% of such issues. The remaining 20% are usually related to the valve train, so inspecting the valve train will completely eliminate the problem.
18
5
Share
Cookie
Cookie Settings
© 2025 Servanan International Pte. Ltd.